Download
Share
Print this page
Flashforge Guider II Quick Start Manual
  1. Manuals
  2. Brands
  3. Flashforge Manuals
  4. 3D Printers
  5. Guider II
  6. Quick start manual

Flashforge Guider II Quick Start Manual

Hide thumbs Also See for Guider II:

Advertisement

Quick Links

Download this manual See also: User Manual
Quick Start Guide
GUIDER II
SZ11-EN-A02
1. Hot! Avoid touching the heating nozzle in operation.
WARNING
2. Moving parts in printer may cause injury. Do not wear gloves
or other sources of entanglement in operation.
USERGUIDE
The User Guide is in the USB stick.
This guide is only applicable to FLASHFORGE Guider II 3D printer

Advertisement

loading
Need help?

Need help?

Do you have a question about the Guider II and is the answer not in the manual?

Questions and answers

Related Manuals for Flashforge Guider II

Summary of Contents for Flashforge Guider II

  • Page 1 WARNING 2. Moving parts in printer may cause injury. Do not wear gloves or other sources of entanglement in operation. USERGUIDE The User Guide is in the USB stick. This guide is only applicable to FLASHFORGE Guider II 3D printer...

  • Page 2: Kit Contents

    Kit Contents Filament Spool 3D Printer Quick Start Guide After-sales Service Card Power Cable USB Cable USB Stick Spool Holder Filament Guide Tube Screwdriver Allen Wrench GREASE Grease Unclogging Pin Tool Wrench Solid Glue...
  • Page 3 Getting to Know Your Guider II 1. Z-Axis Guide Rod 2. Filament Inlet 3. Y-Axis Guide Rod 4. X-Axis Guide Rod 8. Leveling Knob 5. Touch Screen 6. Touch Screen Button 7. Build Plate 11. Nozzle 9. Servo 10. Turbo Fan 12.
  • Page 4 Unpacking 1. Open the box and remove both top foam 2. Take your Guider II out of the box and remove sheets. the bubble wrap. 3. The bottom PE foam should contain: filament, 4. Remove bubble wrap. spool holder, solid glue, USB cable, grease and accessories bag.
  • Page 5 About 9. Press the touch screen button and tap [Tools] .10. Tap [Manual]. X: 87.00 Y: 70.50 Z: 140.00 11. Tap [Z-] to partially elevate the build plate. 12. Remove both bottom foam pieces. Congratulations! You've unpacked your Guider II.

  • Page 6: Hardware Assembly

    Hardware Assembly 1. Locate the spool holders.Install the spool 2. Turn down the spool holder to make the holder holders in the two quadrangular openings on bottom cleave to the printer back. the back.To install a spool holder, level it and insert the end into one of the openings.
  • Page 7 Leveling Build Platform How to change language HOME Filament Level Home Manual Print Preheat Tools Setting Status About Language English 简体中文 English Resume Print 日本語 WiFi WLan hotspot 繁體中文 How to use the leveling knobs Rotate the knob clockwise Raise the build plate to reduce the distance between the nozzle and build plate. Rotate the knob Anticlockwise Lower the build plate to increase the distance between the nozzle and build plate.
  • Page 8 [OK] button. 1. Tap [Tools]-[Level] on your Guider II's touch screen. Please wait while the extruder and platform complete initial movements. Then, rotate all three knobs under the platform anticlockwise until you can't tighten them anymore.

  • Page 9: Loading / Changing Filament

    Loading / Changing Filament HOME Filament Level Home Manual Build Preheat Tools Setting Status About 1. Tap [Tools] and then tap [Filament] and [Load] to load filament. I’m heating up... 100% 220℃ / 220℃ Extruder Load Unload Cancel 2. The extruder will automatically heat up. Once heated, filament will be drawn through the extruder.

  • Page 10: First Print

    Ensure that the filament has been loaded in an appropriate approach. Load the filament for a while to extrude all the melted filament you printed last time out of the extruder. Do not leave the Guider II unattended during operation.
  • Page 11 Scan QR to Get More After-Sales Support After-Sales Service: support@ff3dp.com Tel: +86 579 82273989 Web: www.flashforge.com Add: 2/F, No.518, Xianyuan Road, Jinhua, Zhejiang, China...