Erasing One Of The Remote Control Button Settings; Resetting The Remote Control Presets; Confirming Preset Codes - Pioneer 7.1 VSX-AX2AV-S Operating Instructions Manual

Controlling the rest of your system
11
4 Point the two remote controls towards each other
then press the button that will be doing the learning on
this receiver's remote control.
PRES KEY starts flashing to indicate the remote is ready
to accept a signal.
• The remote controls should be 3–5 cm apart.
5 Press the corresponding button on the other remote
control that is sending (teaching) the signal to this
receiver's remote control.
For example, if you want to learn the playback control
signal, press and hold
show OK if the operation has been learned.
If for some reasons the operation hasn't been learned the
LCD will display ERROR briefly and then display PRES
KEY again. If this happens, keep pressing the (teaching)
button as you vary the distance between the two remotes,
until the LCD display shows OK.
Certain buttons represent operations that cannot be
learned from other remote controls.
available are shown below (with the exception of the TV
controls, a combination of SHIFT and these buttons can
also be learned):
RECEIVER INPUT
SELECT
CD TV
DVD SAT
DVR2 CD-R
DVR1 i Pod
SLEEP
SR+
D.ACCESS
+10
AV PARAMETER
TOP MENU ì
TUNE
ST
SETUP SETUP
TUNE
PTY SEARCH
GUIDE
TV CONTROL
6 To program additional signals for the current
component repeat steps 4 and 5.
To program signals for another component, exit and
repeat steps 1 through 5.
Note
1 Note that interference from TVs or other devices will sometimes result in the remote control learning the wrong signal.
2 • Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.
• If the remote LCD shows FULL, it means the memory is full. See Erasing one of the remote control button settings below to erase a programmed button
you're not using to free up more memory (note that some signals may take more memory than others).
3 Note that the number key decimal button (+10/D.ACCESS) may not be learned with some components.
68
En
3 – 5 cm
briefly. The LCD display will
2
3
The buttons
SYSTEM OFF
SOURCE
VIDEO 2
VIDEO 1 TV CONT
MULTI IN ROOM2/3
TUNER RECEIVER
VIDEO ANALOG
SEL ATT
DIMMER
TV CONTROL
INPUT
TV VOL TV CH
SELECT
CLASS
DISC
ENTER
REC
CH LEVEL A
MENU
MPX EON REC STOP
B C D
ST T.EDIT
ENTER
RETURN RETURN
AUDIO SUBTITLE HDD
DISP CH
BAND
STATUS SIGNAL SEL SBch STEREO
7 Press and hold the RECEIVER button for a couple of
seconds to exit and store the operation(s).
Erasing one of the remote control
button settings
This erases one of the buttons you have programmed and
restores the button to the factory default.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
The LCD on the remote prompts you for the component
corresponding to the button setting to be erased.
1
3 Press the input source button corresponding to the
command to be erased then press ENTER .
The LCD display flashes PRES KEY.
4 Press and hold the button to be erased for two
seconds.
The LCD display shows OK or NO CODE to confirm the
button has been erased.
5 Repeat step 4 to erase other buttons.
6 Press and hold the RECEIVER button for a couple of
seconds when you're done.

Resetting the remote control presets

This will erase all preset remote control preset codes and
programmed buttons.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
RESET flashes in the LCD display.
3 Press and hold ENTER for about two seconds .
The LCD shows OK to confirm the remote presets have
VOL
been erased.
MUTE
E

Confirming preset codes

DVD
CH
Use this feature to check which preset code is assigned
to an input source button.
1 While pressing the RECEIVER button, press SETUP .
The remote LCD display shows SETUP.
2 Use
The LCD on the remote prompts you for the input source
button you want to check.
to select ERASE then press ENTER .
to select RESET then press ENTER .
to select READ ID then press ENTER .