Checking The I.link Inputs; About I.link - Pioneer 7.1 VSX-AX2AV-S Operating Instructions Manual

Other connections
1 Use an i.LINK cable to connect one of the i.LINK
connectors on this receiver to an i.LINK connector on
your i.LINK component.
MULTI-ROOM
&SOURCE
/REC SEL
OUT1
FM UNBAL 75Ω
ROOM3(ZONE3)
MULTI-ROOM & SOURCE
ROOM2(ZONE2)
IN OUT
OUT2
S400
IR
USB
AUDIO
12 V TRIGGER
IN
(AUDIO)
1 2
IN1
(DC OUT 12V TOTAL 50mA MAX)
(SAT)
ROOM2 MULTI-ROOM
S400
& SOURCE
MONITOR
IN2 (ZONE2) OUT
(DVR/
OUT
HDMI IN1
VCR 1)
IN1(DVD/LD)
IN1
Y Y
IN2(TV)
IN3
1–2
(DVR/
ASSIGNABLE
VCR 2)
IN4 P P
B B
(CD-R)
1–4
IN2
ASSIGNA-
BLE
P P
R R
1–2
IN1
(DVD/
IN2 IN3 IN3
LD)
Y Y
OUT
IN2
(CD)
P P
B B
P P
R R
S - VIDEO
1–3
ASSIGNABLE
DIGITAL COMPONENT VIDEO
S400
(AUDIO)
i.LINK-equipped component
• The arrow on the cable connector body should be
lined up with the arrow (to the left of the connector)
on the receiver for correct alignment. The i.LINK
cable should be inserted straight into the connector
so that it snaps easily into place. If not connected
properly the receiver will not be able to recognize any
connected components. Note that the i.LINK cable is
fragile and can be broken easily if too much force is
used when connecting.
2 Assign the i.LINK component to the input you want,
then make any necessary output settings on the
component.
See The Input Setup menu on page 60 to assign the
component to an input function on this receiver. Follow
the operating instructions that came with the component
to make any necessary output settings.
• You can connect several components together using
i.LINK. See Creating an i.LINK network below.
AUDIO PRE OUT
ANTENNA
R L
PHONO
F
AM LOOP
IN
MONITOR MULTI-ROOM & SOURCE
OUT
R ROOM2(ZONE2) L SUB W. C
CD
OUT IN
DVD/
LD
IN1
IN
OUT
TV
IN2 IN
CD-R/
R L
TAPE
SAT
IN
IN
R L
FR FL iPod
VIDEO1/
GAME1
IN
IN
SUB W. CENTER
OUT
SUR-
DVR/
ROUND
VCR 1
IN
R L
OUT
DVR/
R L
SURROUND RS-232C
VCR 2
BACK
IN
MULTI CH
IN
OUT IN
R L
VIDEO
CONTROL
VIDEO AUDIO
VSX-AX4AVi

Checking the i.LINK inputs

If you have several i.LINK-equipped components and
have assigned them to input functions in The Input Setup
menu on page 60, you can confirm the settings you made
below.
1 Select 'i.LINK Check' from the Other Setup menu
and press ENTER.
See The Other Setup menu on page 61 for more on
navigating this menu screen.
• If no i.LINK-equipped components are connected
i.LINK Check cannot be selected.
7.Other Setup
a.Multi Room Setup
b.SR+ Setup
c.OSD Adjustment
d.i.LINK Check
:Return
2 Scroll through the list to confirm your settings.
When a number of i.LINK-equipped components are
connected to your receiver, the i.LINK-equipped
component you are looking for might be listed on
additional display screens.
• i.LINK is displayed after unassigned device names
(e.g. DV-989AVi [i.LINK]).
• If a connected devices cannot output (playback) a
source using the i.LINK connection, [- - - -] is
displayed after the input device name (e.g. DV-
989AVi [- - - -]). Non-compatible devices cannot be
assigned to inputs.
• When the cables for an assigned input device
become loose or the power is cut to the device, an
asterisk (*) appears before the device name (e.g.
*DV-989AVi [CD]).
3 When you're finished, press RETURN .
You will return to the Other Setup menu.

About i.LINK

i.LINK is a trademark name for IEEE1394, a high-speed
interface for digital audio, video and other data found on
personal computers, digital camcorders, and other kinds
of audio and audio/visual equipment. A single i.LINK
connector can both send and receive data at the same
time, so only one cable is required to connect compo-
nents for two-way communication.
"i.LINK" and the "i.LINK" logo are trademarks of Sony
Corporation.
7d.i.LINK Check (1/2)
( End )
* DVD-Audio5 : TV
1 DVD-Audio1 : DVD
2 DVD-Audio2 : DVR
3 DVD-Audio3 : i.LINK
4 DVD-Audio4 : i.LINK
5 DVD-Video1 : ----
( Next )
:Return
08
49
En