Erasing One Of The Remote Control Button Settings; Clearing All The Remote Control Settings; Direct Function - Pioneer VSX-D710S Operating Instructions Manual

Controlling the Rest of Your System
Erasing One of the Remote
Control Button Settings
This erases one of the buttons you have programmed
and restores the factory installed preset to that button
VSX-D710S/D810S
Press SETUP and hold for three seconds
The LED on the remote control will light for two
seconds
Press the MULTI CONTROL button relating
to the function of the button to be cleared
The remote control will return to the previous mode
after thirty seconds of inactivity
Press the RECEIVER c> button twice within
three seconds to start erase mode
The LED blinks
Press the button to be cleared for three
seconds
The LED lights steadily for three seconds and then
goes off
Repeat steps 4 to erase other codes
Press and hold the SETUP button for one
second to exit the erase mode
VSX-D850S
1 Press SETUP and hold for three seconds
The LED on the remote control will light for two
seconds and the display shows SETUP
2 Use the 4
D
buttons to select the Erase mode
The LCD display shows ERASE
3 Press the MULTI CONTROL button relating
to the function of the button to be cleared
4 Press the button you want to clear
5 Repeat steps 3-4 to erase other codes
Clearing All the Remote
Control Settings
Clears all presets, all learned functions and restores the
factory presets
1 Press SETUP and hold for three seconds
For the VSX-D710S and VSX-D810S the LED on the
remote control lights for two seconds For the VSX-
D850S the SETUP icon lights
If you want to cancel the Clearing mode, press
SErUP
The remote control will also return to the previous
mode after thirty seconds of inactivity
2 Use the number buttons to enter 0123
The LED light for half a second for each digit input
On the VSX-D710S and VSX-D810S the LED lights
for two seconds to indicate that the setings have been
restored to the factory presets (If the LED blinks
three times, then you made a mistake with the
code-try re-entering it ) On the VSX-D850S the
LCD displays 0123 and then "OK" for two seconds if
the four digit code has been accepted If any error has
occurred display will blink three times
Direct Function
The direct function is a useful feature which allows you
keep the receiver in one function (for example, CD)
while putting the remote control in a different function
This could let you, for example, use the remote control
to set up and listen to a CD on the receiver and then use
the remote control to rewind a tape in your VCR while
you continue to listen to your CD player
When the DIRECT function is ON any MULTI
CONTROL button you press will change the function of
both the receiver and the remote control When you
turn the DIRECT function OFF, you can operate the
remote control without affecting the receiver Thus you
could switch the remote control the VCR and operate
that component while the receiver plays a different
component
To set a MULTI CONTROL button to DIRECT ON or
DIRECT OFF
Press SETUP and hold for three seconds
On the VSX-D7 1 OS and VSX-D8 10s the LED on the
remote control will light for two seconds On the
VSX-D850S the LCD display SETUP icon will light
If you want to cancel the Direct Function mode, press
SETUP
The remote control will also return to the previous
mode after thirty seconds of inactivity
Press the MULTI CONTROL button that you
want to set up
Use the number buttons to enter 9990
(DIRECT ON) or 9995 (DIRECT OFF)
The LED will light for half a second on each digit
input Then, on the VSX-D710S and VSX-D810S the
LED will light for two seconds to indicate that it's
been correctly set (If the LED blinks three times,
then you made a mistake with the code-try re-
entering it ) On the VSX-D850S, the LCD will display
"OK" to show the four digit code has been accepted
If it hasn't been accepted the display will blink three
times
MEMO:
l
TV CONT doesn't have this feature and thus can't use
the DIRECT FUNCTION
39
En