Wireless Key Predefined Default Templates - ADEMCO VISTA-10P Programming Manual

This prompt appears only for hard-wired zones 01-06 (zone 02 is used as an example in display).
02 Response Time
Enter the desired response time for this zone:
0 = 10mSec; 1 = 350mSec; 2 = 700mSec; 3 = 1.2 seconds
1
[∗] to continue
This prompt is skipped for zones 1-6.
10 INPUT TYPE
Select the desired input type for the transmitter zone being programmed (some transmitters have more than
RF TRANS 3 one input loop, each requiring its own zone; e.g., a 5804's four inputs requires four zones).
3 = RF (supervised RF transmitter; sends fault, restore, and low-battery signals, and sends periodic check-
4 = UR (unsupervised RF transmitter; sends fault, restore, and low-battery signals, but does not send
5 = BR (unsupervised button type RF transmitter; sends fault and low battery signals when activated, does
[∗] to continue
NOTES:
• For the built-in basic wired zones, the Input Device type is automatically displayed as HW and cannot be
For wireless transmitters, enroll the serial number and loop number.
10 INPUT S/N: L
1. a. Transmit two open/close sequences. If using a button-type transmitter, press and release the button
A 0 2 2 - 4 0 6 4 1
2. Press [∗] to continue. The system now checks for a duplicate serial/loop number combination.
If the serial/loop number combination is not a duplicate in the system, a display showing the serial number
10 INPUT S/N L
and loop number entry appears.
A 0 2 2 - 4 0 6 4 1
[∗] to continue
This prompt will only appear if you answered "Yes" at the "SET TO CONFIRM" prompt.
XMIT TO CONFIRM
The system now enters a confirmation mode so that the operation of the actual programmed input can be
PRESS TO SKIP confirmed.
Activate the loop input or button that corresponds to this zone.
[∗] to continue
If the serial number transmitted does not match the serial number entered, a display similar to the one
E n t d A 0 2 2 - 4 0 6 3 1
shown appears. If the loop number does not match, it will also be displayed.
R c v d A 0 2 2 - 4 0 6 4 1
If so, activate the loop input or button on the transmitter once again. If a match is not obtained (i.e., summary
display does not appear), press the [#] key twice and then enter (or transmit) the correct serial number.
[∗] to continue
If the serial number transmitted matches the serial number entered, the keypad will beep 3 times
Zn ZT RC In: L
and a summary display will appear, showing that zone's programming. Note that an "s" indicates
10 03 10 RF: 1s that a transmitter's serial number has been enrolled.
[∗] to accept the zone information and continue
If you want to program descriptors for the zone now, enter 1 (yes) and refer to the *82 Descriptor
PROGRAM ALPHA?
Programming section for procedures.
0 = NO 1 = YES 0 To program descriptors later, enter 0 (no).
[∗] to continue
If 0 (No) was entered at the Program Alpha prompt, the system will return you to the ZONE NUMBER
E N TE R Z N N U M.
prompt. Repeat these steps for each zone in the system.
When all zones have been programmed, enter 00 as the zone number to quit.
( 0 0 = Q U I T) 1 1
[∗] to continue

Wireless Key Predefined Default Templates

For 5804
Loop
TEMPLATE 1 1
2
3
4
TEMPLATE 2 1
2
3
4
TEMPLATE 3 1
2
3
4
in signals; transmitter must stay within receiver's range)
periodic check-in signals; transmitter may be carried off-premises)
not send restore or check-in signals; transmitter may be carried off-premises)
edited.
twice, but wait about 4 seconds before pressing the button the second time.
OR
b. Manually enter the 7-digit serial number printed on the label of the transmitter.
Press the [∗] key to move to the "L" position, then enter the loop number (see Loop Identification chart
on back cover).
If desired, you can press the [C] key to copy the previously enrolled serial number (used when
programming a transmitter with several input loops). The cursor moves to the loop number position.
c. To delete an existing serial number, enter 0 in the loop number field. The serial number will change to
0's. If 0 was entered in error, simply re-enter the loop number or press [#], and the serial number will
return to the display.
Function Zone Type
No Response 23
Disarm 22
Arm Away 21
No Response 23
No Response 23
Disarm 22
Arm Away 21
Arm Stay 20
24-hour audible 7
Disarm 22
Arm Away 21
Arm Stay 20
For 5804BD
Loop
TEMPLATE 4 1
2
3
4
TEMPLATE 5 1
2
3
4
TEMPLATE 6 1
2
3
4
– 8 –
Function Zone Type
No Response 23
No Response 23
Arm Away 21
Disarm 22
No Response 23
Arm Stay 20
Arm Away 21
Disarm 22
24-hour audible 7
Arm Stay 20
Arm Away 21
Disarm 22