Tektronix WFM6120 Security Instructions
Waveform monitors
Hide thumbs
Also See for WFM6120:
- Technical reference (152 pages) ,
- Service manual (95 pages) ,
- Release notes (9 pages)
Advertisement
Quick Links
Download this manual
See also:
Service Manual
Advertisement
Related Manuals for Tektronix WFM6120
Summary of Contents for Tektronix WFM6120
- Page 1 WFM6120, WFM7020, and WFM7120 Waveform Monitors Declassification and Security Instructions www.tektronix.com 071-2295-00...
- Page 2 Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or suppliers, and are protected by national copyright laws and international treaty provisions. Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supersedes that in all previously published material.
-
Page 3: Table Of Contents
Table of Contents Preface ......................Clear and Sanitize Procedures..................Memory Devices....................Data Export Devices................... Troubleshooting..................... How to Clear or Sanitize a Non-Functional Instrument ........... How to Recover from Clearing or Removing the Instrument’s Memory ........ WFM6120, WFM7020, and WFM7120 Declassification and Security... - Page 4 Table of Contents WFM6120, WFM7020, and WFM7120 Declassification and Security...
-
Page 5: Preface
Products The following Tektronix products are covered by this document: WFM6120 (Options CPS, EYE, PHY, AD, BAS, PER, ALY, AVD, DAT) WFM7020 (Options HD, CPS, AD, DL, BAS, PER, ALY) WFM7120 (Options HD, CPS, EYE, PHY, AD, DDE, DL, SIM, BAS, PER,... - Page 6 Scrub. This is equivalent to sanitize. User-modifiable. The user can write to the memory device during normal instrument operation, using the instrument interface or remote control. Volatile memory. Data is lost when the instrument is powered off. WFM6120, WFM7020, and WFM7120 Declassification and Security...
-
Page 7: Clear And Sanitize Procedures
20 seconds SDRAM 16 M X 16 Rasterizer User can U651, U661 on Main None Remove the power SDRAM initiate board source from the capture to this instrument for at memory least 20 seconds WFM6120, WFM7020, and WFM7120 Declassification and Security... - Page 8 U445 on Main board See Clear Diagnostic None Main board Pix software during Log Procedure. Mon calibration, calibration and Recalibrate Pix mon and factory only diagnostics to overwrite existing Looping diagnostic values. mode control WFM6120, WFM7020, and WFM7120 Declassification and Security...
- Page 9 “000.000.000.000” for the IP address. 4. Repeat Step 3 for the Subnet Mask, Gateway Address, and SNMP Trap Address 1 through SNMP Trap Address 4. 5. Press the CONFIG button to exit the configuration menu. WFM6120, WFM7020, and WFM7120 Declassification and Security...
-
Page 10: Data Export Devices
5. Press the CONFIG button to exit the configuration menu. Enable Ethernet and SNMP To enable Ethernet and SNMP access, use the same procedures you would use to disable these devices, but select On to enable each device. Access Procedure WFM6120, WFM7020, and WFM7120 Declassification and Security... -
Page 11: Troubleshooting
How to Clear or Sanitize a Non-Functional Instrument To sanitize a non-functional instrument, remove the Main board and return the instrument to Tektronix for installation of a new Main board. This procedure does not clear calibration constants stored on the Audio, Eye and Composite boards.
Need help?
Do you have a question about the WFM6120 and is the answer not in the manual?
Questions and answers