Related Manuals for Zodiac Z300 M4
Summary of Contents for Zodiac Z300 M4
- Page 1 Z300 PM30 EverFirst Instructi ons for installati on and use English More documents on: www.zodiac-poolcare.com H0548600.B - 2016-05...
- Page 2 WARNINGS • Failure to respect the warnings may cause serious damage to the pool equipment or cause serious injury, even death. • The appliance is intended for a specifi c pool use and must not be used for any use other than that for which it was designed.
-
Page 3: Table Of Contents
It is prohibited to distribute or modify this document in any way without authorisati on from • Zodiac®. Zodiac® is constantly developing its products to improve their quality; therefore, the • informati on contained in this document may be modifi ed without noti ce. -
Page 4: ❶ Installati On
❶ Installati on 1.1 I Selecti ng the locati on • The device must be installed at a minimum distance from the pool's surrounding edge. This distance is determined by the electrical standards which apply in the installati on country. •... -
Page 5: I Hydraulic Connecti Ons
1.2 I Hydraulic connecti ons • The device will be connected with a Ø50 PVC pipe, using the half union connectors supplied (see § “5.1 I Descripti on”), to the pool's fi ltrati on circuit, aft er the fi lter and before the water treatment. •... -
Page 6: I Electricity Supply Connecti Ons
1.3 I Electricity supply connecti ons • Incorrectly ti ghtened terminals may cause the terminal unit to heat up and invalidate the warranty. • Before any work inside the device, you must cut the electricity supply as there is a risk of electric shock which may cause material damage, serious injury or even death. -
Page 7: I Opti On Connecti Ons
1.4 I Opti on connecti ons Connecti ng the "Heati ng priority", "On/off command" and "Alarm" opti ons: • Any incorrect connecti on to terminals 1 to 8 may damage the device and cancel its warranty. • Under no circumstances should the fi ltrati on pump motor be supplied via terminals 1-2. •... - Page 8 1.4.4 Remote "on/off " control opti on • This opti on enables the "on/off " butt on functi on to be transferred via a switch or home automati on system installed by remote. • For the connecti on, remove the shunt between terminals 7-8 and connect the switch cable in place (potenti al free contact, no polarity, 220-240V ~ 50Hz).
-
Page 9: ❷ Use
❷ Use 2.1 I Operati ng principle Your heat pump uses the calories (heat) in the air to heat up your pool's water. The process to heat your pool's water to the temperature you want may take a few days as it depends on the weather conditi ons, your heat pump's power and the diff... -
Page 10: I Operati Ng
2.3 I Operati ng • Check that there are no tools or other foreign objects in the machine. • The panel that provides access to the technical secti on must be put in place. • Set the valves as follows: valve B wide open, valves A, C, D and E closed : water entry valve : by-pass valve : water exit valve... -
Page 11: I Presentati On Of The Menu
2.5 I Presentati on of the menu To access the menu, press To browse the menus and modify the values, press To validate a selecti on, press To exit the menu, press Select the language for the interface (2 languages available: French and English) Opti onal Select the device's operati ng mode:... -
Page 12: ❸ Maintenance
❸ Maintenance 3.1 I Wintering • Wintering is vital to prevent the condenser breaking due to freezing. This is not covered by the warranty. • To avoid damaging the equipment with condensati on, do not fully cover it; a wintering cover is provided. -
Page 13: ❹ Troubleshooti Ng
❹ Troubleshooti ng • Before you contact your reseller, please carry out these few simple checks using the following tables if a problem occurs. • If the problem conti nues contact your reseller. • : Acti ons reserved for a qualifi ed technician 4.1 I Device behaviour •... -
Page 14: I Error Code Display
4.2 I Error code display Display Possible causes Soluti ons Resetti ng ST4 sensor temperature Wait unti l the exterior temperature Automati c too low rises Exchanger protecti on in cool mode Automati c if ST3 sensor temperature Clean the evaporator, if problem ST3 sensor over 60°C or evaporator persists, call an approved technician... -
Page 15: I Additi Onal Menus
Display Possible causes Soluti ons Resetti ng By electricity supply Sensor is faulty or offl ine (J7-A1 disconnecti on or Reconnect or change the sensor ST5 sensor error connector) automati c if the compressor discharge fault disappears sensor Check the J8, J9, J7 and J4- Bad connecti on between the A1 By electricity J5 connectors on the link cable... -
Page 16: I Wiring Diagrams
4.4 I Wiring diagrams 4.4.1 Z300 M4-M5-M7 - PM3041-PM3051-PM3061 - EverFirst 8M-11M-13M 4.4.2 Z300 T5 - PM3053 - EverFirst 11T H0548600.B - EN - 2016-05... - Page 17 4.4.3 Z300 MD5 - PM3052 - EverFirst 11MD 4.4.4 Z300 MD8 - PM3072 - EverFirst 15MD H0548600.B - EN - 2016-05...
- Page 18 4.4.5 Z300 TD5-TD8 - PM3056-PM3076 - EverFirst 11TD-15TD REV VALVE 4-channel valve coil Water regulati on sensor Electronic regulati on board Anti -freeze sensor Electronic display board Defrost sensor Electronic release board Fluid line sensor Low pressure switch Compressor backfl ow sensor Venti lator condenser Varistor Compressor condenser...
-
Page 19: ❺ Specifi Cati Ons
❺ Specifi cati ons 5.1 I Descripti on *In a bag in the technical compartment Z300 PM30 EverFirst Ø50 connector to be glued (x2) Gland Anti -vibrati on studs (x5) Wintering cap (x2) Wintering cover Heati ng priority Remote control Plant room kit Condensate pan PAC NET... -
Page 20: I Technical Specifi Cati Ons
5.2 I Technical specifi cati ons Reversible Standards Z300 PM30 PM3041 PM3051 PM3053 PM3061 PM3052 PM3056 PM3072 PM3076 EverFirst 11MD 11TD 15MD 15TD 5 to 38 °C -8 to 38 °C Operati ng temperature range water 10 to 32 °C Defrosti ng by forced air circulati on Defrosti ng by cycle inversion... - Page 22 Votre revendeur Your retailer Modèle appareil Appliance model Numéro de série Serial number Trouvez plus d’informations et enregistrez votre produit sur More informations and register you product on www.zodiac-poolcare.com ZODIAC® is a registered trademark of Zodiac International, S.A.S.U., used under license.