Table of Contents
Advertisement
WARNING:
!
For your own safety, turn off power at fuse box or circuit breaker before trouble shooting your fan.
Some suggested remedies require the attention of a licensed electrician.
T
R
O
U
B
L
E
1. Fan will not start.
2. Fan sounds noisy.
3. Fan wobbles
excessively.
Trouble Shooting
P
R
O
B
A
B
L
E
1. Fuse or circuit breaker blown.
2. Loose power line connections to the fan,
or loose switch wire connections in the
switch housing.
3. Reversing switch in neutral position.
1. Blades not attached to fan.
2. Loose screws in motor housing.
3. Screws securing fan blade flanges to
m
t o
r o
h
u
b
a
e r
o l
o
s
. e
4. Wire connectors inside switch housing
a r
t t
n i l
. g
5. Screws holding blades to flanges
are loose.
1. Setscrew in motor coupling is loose.
2. Setscrew in hanger ball/downrod
a
s s
e
m
b
y l
s i
o l
o
s
. e
3. Screws securing fan blade flanges to
m
t o
r o
a
e r
o l
o
s
. e
4. Fan blade flanges not seated properly.
5. Hanger bracket and/or ceiling bracket
s i
n
t o
s
e
c
u
e r
y l
a f
s
e t
n
e
. d
6. Fan blades out of balance.
C
A
U
S
E
1. Check main and branch circuit fuses or circuit
breakers.
2. Check line wire connections to fan and switch
wire connections in the switch housing.
WARNING: Make sure main power is
!
turned OFF.
3. Make sure reversing switch position is all the
way to one side.
1. Attach blades to fan before operating.
2. Check to make sure all screws in motor housing
are snug (not over-tight).
3. Check to make sure the screws which attach
h t
e
4. Check to make sure wire connectors in switch
h
o
u
against the interior wall of the switch housing.
WARNING: Make sure main power is
!
turned OFF.
5. Tighten screws securely.
1. Tighten both setscrews securely in the motor
coupling.
2. Tighten the setscrew in the hanger ball/
d
o
w
3. Check to be sure screws which attach the fan
b
a l
d
4. Check to be sure the fan blade flanges seat
firmly and uniformly to the surface of the motor.
If flanges are seated incorrectly, loosen the
flange screws and retighten according to the
procedure in the section on "Assembly
Instructions".
5. Tighten the hanger bracket screws to the
c
i e
n i l
6. Interchanging an adjacent (side-by-side) blade
pair can redistribute the weight and result in
smoother operation.
9
S
U
G
G
E
S
T
E
D
R
E
M
a f
n
f
a l
n
g
e
s
o t
h t
e
m
t o
r o
h
u
s
n i
g
a
e r
n
t o
a r
t t
n i l
g
a
g
a
n i
t s
n
o r
d
a
s s
e
m
b
. y l
e
f
a l
n
g
e
s
o t
h t
e
m
t o
r o
a
e r
g
o j
s i
. t
E
D
Y
b
a
e r
t
g i
h
. t
e
a
c
h
o
h t
r e
r o
t
g i
h
. t
Model No.: ACF765
Advertisement
Table of Contents
