Related Manuals for Blizzard Lighting switchblade
Summary of Contents for Blizzard Lighting switchblade
-
Page 1: Switchblade™ Led
Blizzard Lighting, LLC www.blizzardlighting.com Waukesha, WI USA Copyright (c) 2014... -
Page 2: Table Of Contents
Features DMX Quick Reference The SwitchBlade™ Pin-up Picture 3. Setup Fuse Replacement Connecting A Bunch Of SwitchBlade™ Moving Heads Data/DMX Cables Cable Connectors 3-Pin??? 5-Pin??? Huh? Take It To The Next Level: Setting up DMX Control Fixture Linking (Master/Slave Mode) Mounting/Rigging 4. -
Page 3: Getting Started
Since we like a challenge, we introduce to you The SwitchBlade™. You now own a one of a kind Moving Head with one of the sharpest beams in the industry. Now that you’ve got your SwitchBlade™, you should carefully unpack the box and check the contents to ensure that all parts are present and in good condition. -
Page 4: Safety Instructions (Don't Stick Your Head In The Oven!)
• Never disconnect the power cord by pulling or tugging on the cord. • Avoid direct eye exposure to the light source while it is on. • Carrying a SwitchBlade™ under your jacket may be viewed as a concealed weapon by law enforcement. -
Page 5: Meet The Switchblade™ Led
2. MEET THE SWITCHBLADE™ LED MOVING HEAD CONTROL FEATURES • 1x CREE XLamp MC-E 4-IN-1 10W LED • 50,000 hours lifespan and low power consumption • Narrow 2 degree beam angle • Outstanding beam effects • High effi ciency LED shutter •... -
Page 6: The Switchblade™ Pin-Up Picture
Figure 1: The SwitchBlade™ Pin-Up Picture Super Fast Single Arm High Power OSRAM 4-in-1 Rotating Yoke Quad Color RGBW LED Super Sharp 2 Degree Beam Ergonomically Correct Handles 4 Button Controls and LCD Display Figure 2: Behind The Beam DMX Out... -
Page 7: Setup
Insert the fuse holder back in its place and reconnect power. Connecting A Bunch of SwitchBlade™ Fixtures You will need a serial data link to run light shows using a DMX-512 controller or to run shows on two or more fi xtures set to sync in mas- ter/slave operating mode. -
Page 8: Cable Connectors
Step 3: Connect other fi xtures in the chain from output to input as above. Place a DMX terminator on the output of the fi nal fi xture to ensure best communication. Page 8 SwitchBlade™ Manual Rev. A © 2014 Blizzard Lighting, LLC... -
Page 9: Fixture Linking (Master/Slave Mode)
• Safety cables MUST ALWAYS be used. • Never mount in places where the fi xture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation. Page 9 SwitchBlade™ Manual Rev. A © 2014 Blizzard Lighting, LLC... -
Page 10: Operating Adjustments
4. OPERATING ADJUSTMENTS The Control Panel All the goodies and different modes possible with the SwitchBlade™ LED are accessed by using the control panel on the front of the fi xture. There are 4 control buttons below the LED display which allow you to navigate through the various control panel menus. -
Page 11: Control Panel Menu Structure
(for Auto Mode) then hit <ENTER>. At this time you will be given the chance to select one of the 8 pre-programmed macros. Use the <UP/DOWN> buttons to select the pro- grammed sequence you would like to run, then hit <ENTER> to confi rm. Page 11 SwitchBlade™ Manual Rev. A © 2014 Blizzard Lighting, LLC... -
Page 12: Dmx Channel Values In-Depth
160 <--> 179 Internal Program 4 180 <--> 199 Internal Program 5 200 <--> 219 Internal Program 6 220 <--> 239 Internal Program 7 240 <--> 255 Internal Program 8 Page 12 SwitchBlade™ Manual Rev. A © 2014 Blizzard Lighting, LLC... -
Page 13: Troubleshooting
Verify proper mode of operation. Is the fi xture in “Auto” mode? On Its Own If your problem persists or isn’t listed contact support@blizzardlighting.com. If your problem isn’t listed, or if problems persist, please contact support: sup- port@blizzardlighting.com. Page 13 SwitchBlade™ Manual Rev. A © 2014 Blizzard Lighting, LLC... -
Page 14: Appendix
Keeping Your SwitchBlade™ As Good As New The fi xture you’ve received is a rugged, tough piece of pro lighting equip- ment, and as long as you take care of it, it will take care of you. That said, like anything, you’ll need to take care of it if you want it to operate as designed. -
Page 15: Tech Specs
Output 3-pin XLR Female Other Operating Modes Standalone, Master/Slave, Sound Active, Auto Other Information When opening a SwitchBlade, never put your hand over the blade 2-year limited warranty, does not cover mal- Warranty function caused by damage to LED’s. Page 15 SwitchBlade™... - Page 16 Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting...