Removal of the Dome Module Bracket & the Dome with sealing ________________________ 10 5.2.2 Removal of the dome sealing ____________________________________________________ 12 5.2.3 Mask Gore filters. _____________________________________________________________ 12 Repaint instruction for P551X series _______________________________________ 13 Repainting of the Chassis __________________________________________________ 13 6.1.1 Removal of the Chassis Hook and Lid _____________________________________________ 14 6.1.2 Removal of the Screws Bayonett _________________________________________________ 14 6.1.3...
Any aftermarket modifications, which are not approved by Axis Communications AB, made on Axis Network Dome cameras will void the Product warranty. Therefore, please note that any deviation from the re-paint instructions described in this document will void the Product warranty.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 4(23) 5 Repaint instruction for P551X-E series To repaint the P551X-E series Dome Network Camera, the camera will have to be divided into thee parts: Weather Shield, Chassis and Dome Module.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 5(23) 5.1.2 Removal of the Dome Module Ass Step 1 Remove the four Antiloss screws that hold the Dome module ass. Remove the Dome module ass.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 6(23) 5.1.3 Removal of the Push-pull Connector Housing Step 1 Remove the two screws that hold the Push-pull connector housing and remove the housing.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 7(23) 5.1.4 Removal of the Chassis Hook Step 1 Remove the three screws that hold the Chassis hook. Tool: Screwdriver Torx20 Torque (when refitting): 2,4Nm...
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 8(23) 5.1.6 Create a masking box for the Chassis and position the unit Cut a circular hole with diameter 147 mm in the middle of the 190x190 mm side of the box.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 9(23) 5.1.7 Masking of the Chassis In order to maintain the fit and function of the camera, some parts of it need to be masked before painting.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 10(23) Mask, 90mm in diameter 5.2 Repainting of the Dome Module Ass When repainting the Dome Module ass, the Cover is the part to repaint. Please follow each step described below.
Page 11
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 11(23) Dome Module bracket) Screws (8x) Dome with Sealing Built-in washer on Dome Module Bracket (4x) When refitting, Please note: 1) Please note the maximum torque of 0,25Nm.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 12(23) 5.2.2 Removal of the dome sealing The dome sealing ring is easilly removed by hand from the cover. Dome sealing ring Cover 5.2.3 Mask Gore filters.
6 Repaint instruction for P551X series To repaint the P551X series Dome Network Camera, the camera will have to be divided into three parts: Chassis, Ass Lid and Dome Module. Please refer to chapter 7.2 for an assembly overview. Each part is then stripped from components to enable the repainting.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 14(23) 6.1.1 Removal of the Chassis Hook and Lid Step 1 Remove the three screws that hold the Chassis hook. Tool: Screwdriver Torx20...
Page 15
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 15(23) Screw Bayonett (3x) When refitting, Please note: Please note the maximum torque of 1,8Nm. - 15 -...
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 16(23) 6.1.3 Create a masking box for the Chassis and position the unit Cut a circular hole with diameter 147 mm in the middle of the 190x190 mm side of the box.
Page 17
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 17(23) Step 1 Mask all the 16 threaded screwholes and the connector together with the corresponding slot on the top surface of the chassis.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 18(23) 6.2 Repainting of the Dome Module Ass When repainting the Dome Module ass, the Cover is the part to repaint. Please follow each step described below.
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 19(23) 6.2.2 Removal of the dome sealing The dome sealing ring is easilly removed by hand from the cover. Dome sealing ring Cover...
AXIS 66583 REV: 2 COMMUNICATIONS AB MANUAL RE-PAINT INST AXIS P551X/-E DATE: 2016-04-07 Author: Sven Svensson PAGE: 23(23) 8 Revision History REVISION DATE AUTHOR DESCRIPTION April 7, 2016 Sven Svensson First Revision April 7, 2016 Sven Svensson Updated Table of content...