Commissioning; Adjustments - Festool KAPEXKS 88 E Original Operating Manual

Laser-specifi c safety information
• Never direct the laser beam at people. It may
cause accidents as a result of the glare.
• Never look into the direct or refl ecting laser
beam. However, if you make direct contact with
the laser beam, close your eyes immediately
and move your head from the beam. Direct eye
contact with the laser beam can cause damage
to the eye.
• Do not make any modifi cations to the laser. A
modifi ed laser can generate additional risks.
Only for AS/NZS: The tool shall always be supplied
via residual current device with a rated residual
current of 30 mA or less.
5.3 Emission levels
Levels determined in accordance with EN 61029
are typically:
Sound pressure level
Noise level
Measuring uncertainty allowance
Wear ear protection.
Measured acceleration
The specifi ed emissions values (vibration, noise)
– are used to compare machines.
– They are also used for making preliminary
estimates regarding vibration and noise loads
during operation.
– They represent the primary applications of the
power tool.
Increase possible for other applications, with
other insertion tools or if not maintained adequat-
ely. Take note of idling and downtimes of machine!
6

Commissioning

Warning
• Observe the mains voltage: The voltage and
frequency of the power source must comply with
the specifi cations on the machine's identifi ca-
tion plate.
• In North America, only Festool machines with
the voltage specifi cations 120 V/60 Hz may be
used.
Prior to initial operation:
– Remove the transport safety device (4.4) from
the guide rod.
On/Off switch
– Press the on/off switch (1.2) as far as possible
to unlock the saw unit and the pivot guard.
– Press the switch-on lock (1.3).
– Press the on/off switch (1.2) all the way in to
start the machine.
– Release the on/off switch again to switch off the
machine.
7
KS 120 EB only: Replace the laser warning sticker
(3.1) with the relevant accompanying warning
sticker in your language.
7.1
Securing the machine (transport position)
– Press the on/off switch (4.1).
– Swivel the saw unit downwards until it reaches
the fence.
– Press the lock (4.2). The saw unit now remains
in the lower position.
88 dB(A)
– Tighten the rotary knob (4.3) to secure the saw
101 dB(A)
unit in the rear position.
K = 3 dB
– Wind up the mains cable into the cable holder
(5.5) before transporting.
– Stow away the Allen key (5.4) and the bevel (5.3)
< 2.5 m/s²
(KS 120 EB only) in the holders provided.
Carry the machine by the edge of the saw table
(5.2) and the handle (5.5) in the cable holder.
Unlocking the machine (working position)
– Push the saw unit down slightly and remove the
transport safety device (4.2).
– Swivel the saw unit upwards.
– Unscrew the rotary knob (4.3).
7.2
Before using the machine, set up on a level, stable
work surface (e.g. the underframe UG-KAPEX, the
multifunction table MFT or a worktop).
The following assembly options are available:
Fastening: Secure the machine on the work sur-
face using four screws. Use the holes (6.1) on the
four support points on the saw table.
Clamps: Secure the machine on the work surface
using four clamps. The fl at surfaces (6.2) on the
four saw table support points are used as clamp-
ing surfaces.
Clamping set (for MFT): Secure the machine on
the Festool multifunction table MFT using the
clamping set (6.4, 494693). Use the two screw
holes (6.3).

Adjustments

Always pull the plug out of the socket
before performing any type of work on
the machine.
Transport
Never carry or lift the machine by the
movable pivot guard (5.1).
Mounting the machine
Always pull the plug out of the socket
before performing any type of work on
the machine.
17