Subscribe to Our Youtube Channel
Related Manuals for AMS CCS811
Summary of Contents for AMS CCS811
- Page 1 Eval Kit Manual DN[Document ID] CCS811 Standard Board CCS811-LG_EK_ST ams Eval Kit Manual Page 1 [v1-01] 2017-Jan-16 Document Feedback...
-
Page 2: Table Of Contents
Introduction .......................... 3 General Description ......................3 USB to I C Board (ENS-USB-I2CIO) ................... 3 CCS811 Sensor Board (ENS-CCS811-SB) ................. 4 Software Installation ......................5 Board Interface and Test Points ..................6 Board Interface ........................6 Test Points ........................... 6 Schematic, PCB Layout and Bill of Materials .............. -
Page 3: Introduction
C board refer to as ENS-USB-I2CIO, as shown in Figure 1, allows control and measurement of the CCS811 sensor board using the ENS Dashboard. By default the USB to I board provides a 3.3 V supply to the CCS811 sensor board. -
Page 4: Ccs811 Sensor Board (Ens-Ccs811-Sb)
CCS811 Standard Board CCS811 Sensor Board (ENS-CCS811-SB) The CCS811 sensor board refer to as ENS-CCS811-SB, as shown in Figure 2, is an evaluation platform for the CCS811 device. It contains a CCS811 digital VOC gas sensor with an ENS210 relative humidity and temperature sensor and has I... -
Page 5: Software Installation
ENS-CCS811-SB Relative humidity and temperature data from ENS210 can be read on the I C bus and this information can be written to CCS811 to compensate for temperature and humidity changes for indoor air quality monitoring. Software Installation Quick steps: ... -
Page 6: Board Interface And Test Points
Optional reset pin. Active low Ground Test Points There are 3 test points for I C address, GND and PWM as shown below on the CCS811 sensor board (ENS-CCS811-SB). Figure 6 CCS811 Sensor Board Test Points Ground Address ams Eval Kit Manual... -
Page 7: Schematic, Pcb Layout And Bill Of Materials
CCS811 Standard Board Schematic, PCB Layout and Bill of Materials The schematic design, PCB layout and bill of materials (BOM) for CCS811-LG_EK_ST is documented in the following sections. Schematic Design The schematic design for USB to I C board (ENS-USB-I2CIO) and the CCS811 sensor board (ENS- CCS811-SB) is documented at the end of the document. -
Page 8: Summary
100kΩ NTC Thermistor 0402-N R2(8-4) NCP15WF104F03RC Murata Summary This document describes the CCS811 evaluation kit about what it is and how to use it from the user point of view. ams Eval Kit Manual Page 8 [v1-01] 2017-Jan-16 Document Feedback... -
Page 9: Ordering & Contact Information
CCS811 Standard Board Ordering & Contact Information Ordering Code Description CCS811-LG_EK_ST CCS811 Eval Kit Standard Board Technical Support is available at: www.ams.com/Technical-Support Provide feedback about this document at: www.ams.com/Document-Feedback For further information and requests, e-mail us at: ams_sales@ams.com For sales offices, distributors and representatives, please visit: www.ams/com/contact... -
Page 10: Copyrights & Disclaimer
AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. -
Page 11: Revision Information
CCS811 Standard Board Revision Information Changes from previous version to current revision 1-01 (2017-Jan-16) Page Minor updates only Note: Page numbers for the previous version may differ from page numbers in the current revision. Correction of typographical errors is not explicitly mentioned. - Page 12 SENSE NINT I2C_SCL X1-3 NRESET X1-2 ADDR X1-1 ADDR 22-23-2071 CCS811 ADDR ADDR PGND 100k 4.7uF NRESET NTC (100k) Relative Humidity + Temperature Sensor I2C_SDA I2C_SCL 100n ENS-CCS811-SB - V1 Design Date: 26 / 10 / 2016 Copyright AMS 2016...
- Page 15 X1-4 NINT X1-5 USB_5V NRESET VBUS X1-6 LED1 GPIO0 X1-7 LED2 CP2112 GPIO1 NWAKE GPIO2 NINT GPIO3 NRESET GPIO4 GPIO5 GPIO6 DUT_VDD -RESET GPIO7 DUT_VDD SUSPEND -SUSPEND ENS-USB-I2CIO LED1 LED2 Design Date: 26 / 10 / 2016 Copyright AMS 2016...
Need help?
Do you have a question about the CCS811 and is the answer not in the manual?
Questions and answers