Related Manuals for Digisol DG-SC3610W
Summary of Contents for Digisol DG-SC3610W
- Page 1 DG-SC3610W Wireless IP Surveillance Pan/Tilt Camera Quick In stallation Guide V1.1 2011-05-09...
-
Page 2: Package Contents
No part of this document can be copied or reproduced in any form without written consent from the company. Trademarks: DIGISOL is a trademark of Smartlink Network Systems Ltd. All other trademarks are the property of the respective manufacturers. Package Contents... -
Page 3: Product Overview
Product Overview Thank you for purchasing DIGISOL DG-SC3610W Wireless IP Surveillance Pan/Tilt Camera. DG-SC3610W is a Megapixel IP Camera with H.264 compression, IR LED and microphone. The Pan/Tilt function allows the camera to monitor a much larger and wider area. Day/Night function with the IR LEDs allows the camera to operate effectively in low light environment. -
Page 4: Front View
Front View DG-SC3610W has one 10/100Mbps RJ-45 port which can be connected to LAN or PC for viewing the camera. Product Overview After installing the IP surveillance camera, you can verify its status from the LED indicators on the front panel as shown below. - Page 5 Rear View Interface Description Interface Description Power Connects to power source Setup secure Wireless using WPS SD HC SD High Capacity card holder Audio Out Connects to external speakers Connects to local network...
- Page 6 Camera installation - Hardware Connect the Ethernet cable to your local area network, and the other end to the LAN port of DG-SC3610W. Plug the power adapter to power outlet, and connect the power connector to the to the power jack located at the back Panel of the IP camera.
-
Page 7: Rear View
Rear View Connect the antennas to the antenna base (located at the back panel of the camera) Place the IP camera at a secure place, and point the camera to the place you wish to monitor. If you wish to mount the camera on the ceiling or wall, please use the tripod connector (located at the bottom of the camera, as shown below) to mount the camera. - Page 8 Camera installation - Software Insert the Setup CD into your CD-ROM drive of notebook/desktop computer. The “Autorun.exe” program should be executed automatically. If not, run “Autorun.exe” manually from “Autorun” folder in the CD. The Installation Wizard show’s four selection, select the program you want to install or click “Exit” to install the program later.
- Page 9 When clicked on ''Install Administrator Utility'' the following window appears, click 'Next' to continue with the installation. You can specify the destination folder of software installation else you can just use the default folder option which appears, click 'Next' to continue with installation..
- Page 10 If you need installation program to create a desktop icon or a quick launch icon then select the check box for “Create a desktop icon” and “Create a Quick Launch icon” then click 'Next' to continue with the installation. Following screen lists the summary of all options chosen up till now, if everything is correct then click 'Install' to start the installation process, or click 'Back' to go back to previous step to modify installation settings.
- Page 11 The installation process will take some time, please be patient. When you see the following screen, it means the software installation process is complete. Please click 'Finish' to finish the procedure (SKYROS Camera Admin software will start after you click 'Finish' button, if you wish to start it later, uncheck 'Launch SKYROS Camera Admin Software' box).
- Page 12 The following screen appears when the “SKYROS Camera Admin Software” is launched. Click on the search button located at the left bottom corner of the screen. When the search is complete, the cameras found in the network are listed. Choose the one you wish to configure and click “Setup Wizard”...
- Page 13 Please enter the default password “1234” and click “OK” to login to the IP setup page of the camera. IP Camera works through the network using TCP/IP Protocol. The IP address setting must be correct for accessing the camera. The wizard program will detect the IP address status of your network automatically and suggest a free IP address for the Camera.
- Page 14 Or select ''DHCP'' to obtain an auto IP setting from DHCP server and click ''OK'' to apply the configuration. Now the setting will be saved. Congratulations! Your Camera configuration is now complete. Web Management of the Camera To access the web configuration of the camera, assign a static IP address to your notebook/desktop computer in the subnet 192.168.2.X with the subnet mask 255.255.255.0 and gateway as 192.168.2.1.
- Page 15 After login, you should see the following messages appear at the top of Internet Explorer (highlighted using RED color). Right-click on the message, and click 'Install ActiveX Control' as shown in the following screen shot. When you see the following message, click 'Install' to install required ActiveX control.
- Page 16 You should be able to see the images captured by the camera now. Congratulations! Now you can start advanced configuration.
- Page 17 If you're trying to connect to the IP camera from Internet, please make sure the port that IP camera uses is not blocked by firewall or other software / hardware. Contact DIGISOL helpdesk, if above solutions do not work. 2. Image refreshes very slowly.
- Page 18 1800-209-3444 (Toll Free) helpdesk@digisol.com sales@digisol.com www.digisol.com...