Related Manuals for Digisol DG-SC3800P
Summary of Contents for Digisol DG-SC3800P
- Page 1 SKYROS SERIES 3 Megapixel Pan Tilt POE IP Camera DG-SC3800P V2.0 2013-07-06...
- Page 3 Thank You for purchasing this high-resolution 3 Megapixel Pan/Tilt IP Camera! DG-SC3800P IP Camera provides 3 Megapixel high-resolution video quality. With the advanced megapixel lens, you can view images remotely in more...
- Page 4 Ultra-high resolution 3 Mega pixel CMOS image sensor. Full Pan / Tilt Control. Digital input / output interface lets you connect peripherals such as external alarm, sensor, etc. Audio output interface/ inbuilt mike, lets you listen to voices from remote places as well as speak to people in remote places.
- Page 5 After installing the IP camera, you can verify its status from the LED indicators on the front panel as shown below. Item No. Item Description Light sensor Detects light level of the place where this IP camera is installed. IR LEDs Lights up when it’s too dark.
- Page 6 LED indicators There are 2 LED’s inside to indicate the operation of this IP camera: Left: Network activity LED On: Ethernet cable connected Off: Ethernet cable disconnected Flash: Network Connectivity Right: Power LED On: IP camera is switched on Off: IP camera is switched off...
- Page 7 Item No. Item Description Audio out Connects to external audio amplifier to output voice. Use 3.5mm audio cable. DC 12V Connects to DC power adapter output. RESET When the IP camera is not functioning properly, you can use a pen or similar object to press this reset button to reset the IP camera.
-
Page 8: Di/Do Pin Assignment
ETHERNET Connects to your local area network by Ethernet (PoE support) cable. Getting power from this Ethernet port if this device connects to PoE switch. SD card slot Insert SD card for video recording. Maximum 32GB of SDHC card supported. DI/DO PIN ASSIGNMENT Item Description... - Page 9 Camera Installation – Hardware 1. Fix the wall mounting metal plate ‘A’ on the wall, secure it by 4 screws at the screw holes indicated by black arrows. You can fix it upside-down when required. ...
- Page 10 2. Insert wall mounting metal plate ‘B’ into the slot at the bottom of this IP camera by the direction indicated by black arrow. 3. Fix wall mounting metal plate ‘B’ by 2 screws. ...
- Page 11 4. Insert the IP camera (with wall mounting metal plate ‘B’ installed) into wall mounting metal plate ‘A’, which is already fixed on the wall. 5. Fix the IP camera on the wall by screwing wall mounting metal plate ‘A’ and ‘B’ together at the place indicated by black arrow.
- Page 12 When mounted on the wall, cables can pass through wall mounting metal plate ‘A’ as indicated by the picture below. 6. Insert Ethernet cable in the Ethernet port of this IP camera. If the other terminal of the cable is connected to a PoE switch then the device will get power from the Ethernet cable and the power adaptor is no more required.
- Page 13 7. Insert DI/DO signal cable(s) into DI/DO port of this IP camera. If you don’t have DI/DO accessories, you can skip this step. 8. Insert AC power adapter’s cable into DC12V port of this IP camera. The LED’s should light up after few seconds, and the IP camera will test its Pan/Tilt motor within 1 minute (Do not disturb IP camera at this stage).
- Page 14 Web Management of the Camera You must know the IP address of IP Camera before you can connect to it. The IP Camera will use DHCP server on your local network to obtain an IP address automatically by default. So, you can check your DHCP server’s IP address lease table to find the IP address of IP Camera.
- Page 15 When you know the IP address of IP Camera, you can connect to it through Internet Explorer web browser by entering its IP address in address bar. The user login screen as shown below will appear when you get connected: IP Camera’s administrator username and password are both ‘admin’...
- Page 16 After ActiveX plugin is installed, you should be able to see the video stream from camera. Congratulations! Now you can start Advanced Configuration.
- Page 17 Camera Installation – Software Insert the set up CD into your CD ROM drive of notebook/desktop computer. Run the ‘Setup.exe’ file program. The wizard as shown below will appear.
- Page 18 The screen as shown below will appear. Click ‘Next’ to continue. Now, click on ‘Install’ as shown below.
- Page 19 Please wait while installation is being performed. This may take few minutes, please be patient. Second part of installation will start automatically.
- Page 20 A new setup window will appear, please click ‘Next’ button to continue. Now, click on ‘Next’ as shown below.
- Page 21 The screen shown below will appear. Click on ‘Install’ as shown below. Installation will take few minutes, please be patient...
- Page 22 Click ‘Finish’ when you see this message. MSDE (Microsoft SQL Database Engine) installation procedure will start at the same time. Please wait until it completes.
- Page 23 Following screen will appear. Click on ‘Finish’. A new icon will appear on your computer’s desktop, you can double click on it to start SKYROS iview.
- Page 24 IP camera uses is not blocked by firewall or other software / hardware. Contact DIGISOL helpdesk, if above solutions do not work. 2. Image refreshes very slowly. Try a higher frame rate setting, if it's not 30fps.