Harris FlexStar Technical Manual page 5

The Harris Replaceable Parts List Index portrays a tree structure with the major items being leftmost in the index.
The example below shows the Transmitter as the highest item in the tree structure. If you were to look at the bill
of materials table for the Transmitter you would find the Control Cabinet, the PA Cabinet, and the Output
Cabinet. In the Replaceable Parts List Index the Control Cabinet, PA Cabinet, and Output Cabinet show up one
indentation level below the Transmitter and implies that they are used in the Transmitter. The Controller Board is
indented one level below the Control Cabinet so it will show up in the bill of material for the Control Cabinet.
The tree structure of this same index is shown to the right of the table and shows indentation level versus tree
structure level.
Example of Replaceable Parts List Index and equivalent tree structure:
Replaceable Parts List Index
Table 7-1. Transmitter
Table 7-2. Control Cabinet
Table 7-3. Controller Board
Table 7-4. PA Cabinet
Table 7-5. PA Amplifier
Table 7-6. PA Amplifier Board
Table 7-7. Output Cabinet
The part number of the item is shown to the right of the description as is the page in the manual where the bill for
that part number starts. Inside the actual tables, four main headings are used:
•
Table #-#. ITEM NAME - HARRIS PART NUMBER - this line gives the information that corresponds
to the
•
Replaceable Parts List Index entry;
•
HARRIS P/N column gives the ten digit Harris part number (usually in ascending order);
•
DESCRIPTION column gives a 25 character or less description of the part number;
•
REF. SYMBOLS/EXPLANATIONS column 1) gives the reference designators for the item (i.e., C001,
R102, etc.) that corresponds to the number found in the schematics (C001 in a bill of material is equiva-
lent to C1 on the schematic) or 2) gives added information or further explanation (i.e., "Used for 208V
operation only," or "Used for HT 10LS only," etc.).
Inside the individual tables some standard conventions are used:
•
A # symbol in front of a component such as #C001 under the REF. SYMBOLS/EXPLANATIONS col-
umn means that this item is used on or with C001 and is not the actual part number for C001.
•
In the ten digit part numbers, if the last three numbers are 000, the item is a part that Harris has pur-
chased and has not manufactured or modified. If the last three numbers are other than 000, the item is
either manufactured by Harris or is purchased from a vendor and modified for use in the Harris product.
•
The first three digits of the ten digit part number tell which family the part number belongs to - for
example, all electrolytic (can) capacitors will be in the same family (524 xxxx 000). If an electrolytic
(can) capacitor is found to have a 9xx xxxx xxx part number (a number outside of the normal family of
numbers), it has probably been modified in some manner at the Harris factory and will therefore show
up farther down into the individual parts list (because each table is normally sorted in ascending order).
Most Harris made or modified assemblies will have 9xx xxxx xxx numbers associated with them.
The term "SEE HIGHER LEVEL BILL" in the description column implies that the reference designated part
number will show up in a bill that is higher in the tree structure. This is often the case for components
that may be frequency determinant or voltage determinant and are called out in a higher level bill
structure that is more customer dependent than the bill at a lower level.
4/18/11
WARNING: Disconnect primary power prior to servicing.
Guide to Using Harris Parts List Information
Part Number
994 9283 001 7-2
992 9244 002 7-3
992 8344 002 7-6
992 9400 002 7-7
994 7894 002 7-9
992 7904 002 7-10
992 9450 001 7-12
Page
Control Cabinet
992 9244 002
Controller Board
992 8344 002
888-2587-001
Transmitter
994 9283 001
PA Cabinet
Output Cabinet
992 9400 002
992 9450 001
PA Amplifier
992 7894 002
PA Amplifier Board
992 7904 002