Related Manuals for Johnson 6.0T
Summary of Contents for Johnson 6.0T
- Page 1 6.0 T TREADMILL OWNER’S MANUAL Read the TREADMILL gUIDE before using this OWNER’S MANUAL.
-
Page 2: Important Precautions
IMPORTANT PRECAUTIONS SAVE THESE INSTRUCTIONS Read the TREADMILL gUIDE before using the OWNER’S MANUAL. When using an electrical product, basic precautions should always be followed, including the following: Read all instructions before using this treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are adequately informed of all warnings and precautions. - Page 3 • When lowering the treadmill deck, wait until rear feet are firmly on the floor before stepping on the deck. • The sole’s material of shoes may cause static issue. To avoid electrical shock, Johnson Fitness STRONgLY recommends wearing • Disconnect all power before servicing or moving the equipment. To clean, wipe surfaces down with soap and slightly damp cloth athletic shoes with rubber soles.
-
Page 4: Grounding Instructions
ENTER YOUR SERIAL NUMBER IN THE BOX BELOW: circuit. This treadmill should be used with a minimum 15-amp circuit. SERIAL NUMBER: WARNING jOHNSON 6.0T TREAdMIll MODEL NAME: Connect this exercise product to a properly grounded outlet only. 3-POLE Never operate product with a damaged cord or plug even if it is working GROUNDED »... -
Page 5: Tools Included
pRE ASSEMBLY TOOlS INClUdEd: TOUCH PAD PANEL AND DISPLAY WINDOWS F 6 mm T-Wrench UNpACkING F 5 mm L-Wrench F 4 mm T-Wrench Place the treadmill carton on a level flat surface. It is recommended that you place a F 4 mm L-Wrench protective covering on your floor. -
Page 6: Assembly Step
ASSEMBLY STEp 1 ASSEMBLY STEp 2 Open hardware bag 1. Lift the runnIng deCK upward until the HARdWARE bAG 1 CONTENTS : HARdWARE bAG 2 CONTENTS : FOOT LaTCh locks. Remove all contents from Cut the yellow banding and get console mast underneath the running deck. - Page 7 ASSEMBLY STEp 3 ASSEMBLY STEp 4 Open hardware bag 3. Disengage the deCK LOCK LaTCh with your HARdWARE bAG 3 CONTENTS : HARdWARE bAG 4 CONTENTS : foot to lower the runnIng deCK. Pull Lead wIre through rIghT COnSOLe BOLT (D) SPRING WASHER (B) FLAT WASHER (C) BOLT (A)
- Page 8 ASSEMBLY STEp 5 ASSEMBLY STEp 6 Open hardware bag 5. HARdWARE bAG 3 CONTENTS : Align SuppOrT bar with holes in COnSOLe BOLT (H) maSTS. 15 mm Qty: 4 YOU ARE FINISHED! Insert bOLTS (h) into all 4 holes of the SuppOrT bar.
-
Page 9: Treadmill Operation
TREADMILL OPERATION This section explains how to use your treadmill’s console and programming. The BASIC OPERATION section in the TREADMILL gUIDE has instructions for the following: • lOCATION Of THE TREAdMIll • USING THE SAfETy kEy • fOldING THE TREAdMIll •... - Page 10 6.0T CONSOlE OpERATION Note: There is a thin protective sheet of clear plastic on the overlay of the console that should be removed before use. A) * lEd dISplAy WINdOWS: time, distance, calories, heart rate, speed, incline and workout profiles.
-
Page 11: Display Windows
1) Check to make sure no objects are placed on the and incline will need to be from the user in this setting. Johnson 6.0T DISPLAYS belt that will hinder the movement of the treadmill. 2) Plug in the power cord and turn the treadmill ON. - Page 12 TARGET pROfIlES TARGET 1 – TIME: Allows user to set a target based on how long they would like to workout. Time targets can range 3) WEIGHT lOSS: Promotes weight loss by increasing and decreasing the speed, while keeping you in your fat burning zone. from 15:00 –...
-
Page 13: Finishing Your Workout
TO RESET THE CONSOlE Hold STOP key for 3 seconds. COOl dOWN Puts treadmill into cool down mode. Cool down lasts for four minutes and reduces speed and incline to allow your heart to readjust to decreased demand. fINISHING yOUR WORkOUT When your workout is complete, the monitor display will flash “FINISHED”... - Page 15 Johnson 6.0T TREADMILL Owner’s Manual 081712’ Rev. 1.0 © 2012 Johnson...
Need help?
Do you have a question about the 6.0T and is the answer not in the manual?
Questions and answers