Programming Instructions; Cycle Times - Dexter Laundry OPL 30 Cycle 200G Express Parts & Service Manual

Programming Instructions

Editing an Existing Cycle
There are 29 preset wash cycles programmed into the washer at the factory. Although these cycles are
common industry cycles, there may be a need to tailor the cycle to meet an exact application. This can easily
be done with the following instructions. Note: It is recommended when changes are made to one or more of
the preset programs that the cycle number and the changes be documented for later reference. Blank cycle
sheets have been provided at the end of the Preset Cycle Information section.
1. Turn on the power to the washer.
2. Turn the Advance/Run/Program key to the Program position (Program Mode LED lights).
The Select Cycle LED is lit.
3. Select the cycle to be edited by using the SCROLL UP/SCROLL DOWN buttons.
The selection is made when the number displayed corresponds with the desired cycle.
4. Push the green ENTER button.
Once depressed, the first of the nine cycle segment LED's will light (top row). The cycle segments
are: Flush, Pre-wash, Wash, Rinse 1, Rinse 2, Rinse 3, Rinse 4, Rinse 5 and Final Rinse/Extract. The
Select Cycle LED is out.
5. Use the SCROLL UP / SCROLL DOWN buttons to light the cycle segment to be changed.
The sequence of steps below is repeated for each cycle segment until all required segments are edited. The
previously stored parameters will appear as each part of the segment data is reviewed.
6. Push the green ENTER button.
The Cycle Time LED lights (lower row of LED's) and the segment LED is out. The tumble time for this
segment will be shown on the display. If no change is required, then continue to the next instruction.
If this value requires changing, then use the SCROLL UP/SCROLL DOWN buttons to change the
tumble time, in 1 minute increments, to the desired value, then continue to the next instruction.
Settings range is from 0 minutes to 30 minutes, except for the Final Rinse/Extract segment, where
the setting range is 1 minute to 30 minutes. REMINDER: If the tumble time is set to zero, the
segment will be skipped in the wash cycle.
7. Push the green ENTER button. (The wash time has now been entered.)
The Water Temperature LED lights and the Cycle Time LED is out. The water temperature for this
segment is displayed. If no change is required, then continue to the next instruction. If a change is
required, then use the SCROLL UP/SCROLL DOWN buttons to change the water temperature.
HH is all hot water, CC is all cold water, CH is an even mix of hot and cold water, and EE is a no
water bath. Entering a temperature value of 20-90 C will result in a heated bath, if temperature of
fill water is less than programmed temperature. When the desired water temperature is selected,
continue to the next instruction.
8. Push the green ENTER button. (The water temperature has now been entered.)
The Water Level LED lights and the Water Temperature LED is out. The water level for this segment
is displayed. If no change is required, then continue to the next instruction. If a change is required,
then use the SCROLL UP/SCROLL DOWN buttons to change the water level. "HI" is a high water
level and "LO" is a low water level. When the desired water level is selected, continue to the next
instruction. When the No Water bath is selected, the water level has no effect. Either water level
can be selected.
9. Push the green ENTER button. (The water level has now been entered.)
The Injection Source LED lights and the Water Level LED is out. The injection source for this segment
is displayed. If no change is required, then continue to the next instruction. If a change is required,
28
Part # 8533-096-001 11/16
Return to Table of Contents
then use the SCROLL UP/SCROLL DOWN buttons to change the injection source. See the
Injection Source table for proper selection. If zero is selected, then no injection source is active
for this segment. When the desired injection source is selected, continue to the next instruction.
When the No Water or EE bath is selected, injection signals are prohibited by the electronic
controller. The programmed injection source value is ignored.
10. Push the green ENTER button. (The injection source has now been entered.)
The Spin Time LED lights and the Injection Source LED is out. The spin time for this segment is
displayed. If no change is required, then continue to the next instruction. If this value requires
changing, then use the SCROLL UP/SCROLL DOWN buttons to change the spin time in 1 minute
increments to the desired value, then continue to the next instruction. Settings range is from 0
minutes to 10 minutes, except for the Final Rinse/Extract segment where the setting range is 1
minute to 10 minutes. REMINDER: If the spin time is set to zero, there will be no spin at the
end of the bath.
11. Push the green ENTER button. (The extract time has now been entered.)
Once depressed, the Spin Time LED is out and the editing of one segment is complete. The next
sequential cycle segment LED lights, unless the segment edited above was the Final Rinse/Extract
segment. If the Final Rinse/Extract segment is edited, after step eleven, the cycle programming is
complete, and the machine will return to the Programming Mode awaiting a cycle select (Step 3).
To exit the programming mode, depress the red STOP button when one of the nine cycle
segment LED lights are lit. The programming changes made prior to the program exit are
retained and the cycle is updated.

Cycle Times

Cycles 1-30 Chemical Signal
Flush 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Prewash 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Wash 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Rinse 1 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Rinse 2 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Rinse 3 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Rinse 4 0-30 min. 1-6
Drain 40 sec.
Int. Spin 0-10 min.
Rinse 5 0-30 min. 1-6
Drain 40 sec.
Extract 1-10 min.
Total * 1-320 min.
* Cycle times are approximate and do not include fill time from empty to low level.
* Fill time from low to high level is included as computer operates during this period.
Return to Table of Contents
Water Level Water Temp
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
High or low Hot, Cold, Warm or Empty
29
Part # 8533-096-001 11/16