Citizen CL-E700 series Technical Manual

Citizen CL-E700 series Technical Manual

Thermal transfer printer
Hide thumbs Also See for CL-E700 series:
Table of Contents

Advertisement

Quick Links

Technical Manual

CL-E700 series
Thermal Transfer Printer

Advertisement

Chapters

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CL-E700 series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Citizen CL-E700 series

  • Page 1: Technical Manual

    Technical Manual CL-E700 series Thermal Transfer Printer...
  • Page 2 NOTICE This document contains proprietary information of Citizen Systems Japan Co, Ltd. No part of this document or its contents shall be used or reproduced without the express permission of Citizen Systems Japan Co, Ltd. ® CITIZEN is a registered trade mark of CITIZEN HOLDINGS CO., LTD., Japan.
  • Page 3 HAPTER PECIFICATIONS HAPTER PERATING RINCIPLE HAPTER ISASSEMBLY AND AINTENANCE HAPTER ROUBLESHOOTING HAPTER ARTS ISTS HAPTER IRCUIT IAGRAMS PPENDICES CL-E700 series...
  • Page 4: Safety Precautions

    • Do not put the printed circuit boards directly on the printer or on the floor. • When disassembling or reassembling, check wires for any damage and do not pinch or damage them. Also, run wires as they were. CL-E700 series...
  • Page 5 Chapter 1 Specifications HAPTER PECIFICATIONS CL-E700 series...
  • Page 6 Chapter 1 Specifications CHAPTER 1 SPECIFICATIONS TABLE OF CONTENTS 1-1. General Specifications ....................1-3 1-2. Printable Area ......................... 1-8 1-3. Printing Position Accuracy ....................1-9 1-4. Adjustable Sensors......................1-10 CL-E700 series...
  • Page 7: General Specifications

    Min. media thickness 0.0635 mm 0.0025" *1: Options can be separately purchased. *2: When a media pitch of less than 25.4 mm (1 inch) is used, set the “Small Media Adjustment” setting in the “Page Setup” menu to “ON”. CL-E700 series...
  • Page 8 • Plessey • UPC/EAN Extensions • UPC-A • POSTNET • Planet Two-dimension • Code49 • PDF-417 • CODA BLOCK • UPS Maxi Code • Micro PDF-417 • Data Matrix • QR Code • GS1 DataBar • TLC39 • Aztec CL-E700 series...
  • Page 9 EUC, JIS, Shift JIS, Unicode, KS Code, GB Code *3: The OCR font may have a low recognition rate according to the reader. *4: UFST and TrueType rasterizer are licensed from Monotype Imaging, Inc. ® *5: “PC866U Ukraina” is available for Datamax emulation only. CL-E700 series...
  • Page 10 (Class A) EN60950-1, EN55022 (Class A), EN55024, EN61000-3-2, EN61000-3-3 GB4943.1-2011, GB9254-1998, GB17625.1-2003 Power consumption 100V: 72W (operating at 6 IPS at 12.5% printing duty), 2.9W (standby) 230V: 65W (operating at 6 IPS at 12.5% printing duty), 2.6W (standby) CL-E700 series...
  • Page 11 “Ribbon Core φ25x114”, Cleaner head, “Manual User’s (CD-R)”, “Guide Quick-Start”, “Safety Instructions”, Label paper, Ribbon, “SA Ribbon Holder” (2 pcs.) Options Auto-cutter unit, Peeler unit, Serial I/F board, Parallel I/F board, Wired LAN I/F board (multi-functional) Wireless LAN board (standard/multi-functional) CL-E700 series...
  • Page 12: Printable Area

    The unprintable areas on both sides apply to any size media. Media guide Maximum media width: 118 mm (4.65") Unprintable area Printable area (0, 0) Printing start position 2.5 mm (0.10") Reference end Direction of media feed 104.0 mm (4.09”) 11.5 mm (0.45”) CL-E700 series...
  • Page 13: Printing Position Accuracy

    *2: Deviation of vertical positioning when printing position is set to 0. *3: Deviation of horizontal positioning when printing position is set to 0. *4: Deviation of vertical printing position when 100 mm is specified from the printing start position. CL-E700 series...
  • Page 14: Adjustable Sensors

    Media transparent sensor) -0.2 to 57.8 mm (-0.01 to 2.28”) (Moveable range of the reflective sensor) Printable area 2.5 mm (0.10") Maximum media width: 118 mm (4.65") Direction of media feed 104.0 mm (4.09”) 11.5 mm (0.45”) 1-10 CL-E700 series...
  • Page 15 Chapter 2 Operating Principles HAPTER PERATING RINCIPLES CL-E700 series...
  • Page 16: Table Of Contents

    Head up sensor (SA Head Up Sensor PCB) ..........2-23 Transparent sensor (SA TRA Sen PCB) and reflective sensor (SA Ref Sensor PCB) ................2-24 Head temperature sensor................2-26 PF motor temperature sensor..............2-27 Ribbon motor temperature sensor............. 2-29 CL-E700 series...
  • Page 17 2-4-1. USB Interface..................... 2-66 Specifications..................... 2-66 Signal line and pin arrangement..............2-66 2-4-2. Wired LAN Interface................... 2-66 Specifications..................... 2-66 Signal line and pin arrangement..............2-66 2-4-3. Serial Interface (Option) ..................2-67 Specifications..................... 2-67 Signal line and pin assignment..............2-67 CL-E700 series...
  • Page 18 Chapter 2 Operating Principles Protocol ..................... 2-68 2-4-4. Parallel Interface (Option) .................. 2-69 Specifications..................... 2-69 Signal line and pin assignment..............2-69 Parallel port status signals when an error occurs ........2-70 Compatible timing specification ..............2-70 CL-E700 series...
  • Page 19: Operation Of Each Mechanism

    Using the sensor output, the ribbon running state as well as the ribbon end are detected SA Ribbon Motor F SA Ribbon Encoder (Ribbon Encoder Sensor) SA Ribbon Control PCB SA Ribbon Sensor (Ribbon Tension Sensor) CL-E700 series...
  • Page 20: Printing Section

    It converts AC input to DC24 V. SA Main PCB SA Head SA TRA Sen PCB (Transparent Sensor) SA Head Up Sensor PCB (Head Up Sensor) SA PF Motor Relay PCB SA Opepane PCB SA Ref Sensor PCB (Reflective Sensor) Unit Power Supply CL-E700 series...
  • Page 21: Media Feed/Printing Mechanism

    “SA Head” and transferred on the media surface. When the “SA PF Motor” turns clockwise, the media is fed backwards. Thermal Elements Ribbon SA Head SA PF Motor SA Platen Media Gear PF Idle Motor Gear Gear PF1 Gear PF2 [Right side view] CL-E700 series...
  • Page 22: Label/Tag Detection Mechanism

    [For label paper/tag with U-shaped notches] * Both sensors are used. Transparent Sensor Photo- Transparent Sensor transistor Reflective Sensor [For tag with black marks] Phototransistor * Reflective sensors alone is used. LEDs Black mark Reflective Sensor Reflective Sensor CL-E700 series...
  • Page 23 Label U-shaped Black mark Label notch Label gap Media Liner Transparent and Reflective sensors Reflective sensor Transparent sensor Sensor to be Media Media used LEDs LEDs Reflective sensor Reflective sensor Media Sensor See Trough Reflect menu CL-E700 series...
  • Page 24 The amount of light is as follows (the largest amount is for “See Through): • Continuous media (None) < Black mark (Reflect) < Label/U-shaped notch (See Through) 2-10 CL-E700 series...
  • Page 25: Ribbon Feed Mechanism

    Gear 5F Ribbon SA Ribbon Motor F Gear Reduction Ribbon 1 Gear 2 Ribbon Gear 3 Ribbon SA Ribbon Gear 4 Ribbon Tension Shaft F Ribbon SA Head SA Platen Roller Ribbon Guide R Media [Right side view] 2-11 CL-E700 series...
  • Page 26 For wider ribbon (4 inches, etc.), set to “4” as a 4: Factory set value Spring Ribbon Return R rough indication to give a strong tension. For narrower ribbon (2 inches, etc.), set to “2” as a rough indication to give weak tension. Ribbon 2-12 CL-E700 series...
  • Page 27 3 steps with the “Knob Tension Adjust”. As you move the knob toward the  mark indicated on the label, since the spring is pushed to the left and compressed, the spring force becomes stronger and stronger tension is applied to the ribbon. 2-13 CL-E700 series...
  • Page 28: Ribbon Running Detection Mechanism

    If no pulse is output from the photointerrupter while the ribbon motor “SA Ribbon Motor F” is taking up the ribbon, the CPU judges as the ribbon end. [Right side view] Ribbon Holder Ribbon Shaft Encoder Photointerrupter SA Ribbon Encoder (Ribbon Encoder Sensor) 2-14 CL-E700 series...
  • Page 29: Print Head Up/Down Detection Mechanism

    Head Block Head Block "Up" position Photo- Interrupter SA Head Up Sensor PCB Head Block "Down" position Photo- Interrupter SA Head Up Sensor PCB (Head Up Sensor) SA Head Up Sensor PCB 2-15 CL-E700 series...
  • Page 30: Head Balance Adjustment Mechanism

    Spring Head R Weak Spring Head L (Movable) (Fixed) Lever Head Balance Cam Head Balance SA Head (Media Width Ribbon Adjustment Dial) Media (Narrow width) SA Platen Strong Taward "9" For wide media SA Head Ribbon Media (Wide width) 2-16 CL-E700 series...
  • Page 31: Media Thickness Adjustment Mechanism

    SA Lever Head Adjust 2 SA Head Holder (Fixed) For soft media Cam Head Adjust (Media Thickness Adjustment Dial) Bracket Head Supporting Thermal elements point SA Head Ribbon Supporting point Media Groove SA Platen For hard media 2-17 CL-E700 series...
  • Page 32: Operation Of Control Parts

    Controls the entire operations of the printer. It consists of CPU, ROM, RAM, FPGA, driver circuits, etc. (3) Operation panel (SA Opepane PCB) A panel used to indicate the operating status of the printer and to set specifications. It consists of 4 keys, 1 LED (Green/Red) and 1 LCD. 2-18 CL-E700 series...
  • Page 33: Thermal Print Head

    This is a circuit to transmit and receive serial data between the printer and the host. (10) Parallel I/F (IEEE1284) (Option) This is the parallel I/F to transmit and receive parallel data between the printer and the host. It supports Centronics Compatible mode, NIBBLE mode and ECP mode. 2-19 CL-E700 series...
  • Page 34: Wireless Lan I/F (Option)

    [SA Head] (384MHz) F-ROM USB 2.0 (128Mbits) (High-Speed/Full-Speed) Stepping Ethernet Paper Feed Motor 10Base-T/100Base-TX Motor [SA PF Motor] Ethernet Driver Operation Panel (SWx4/LED/LCD) [SA Opepane PCB] RS232C IEEE1284 Ethernet I/F (Multi-function type) Wi-Fi I/F (Option) Interface Board 2-20 CL-E700 series...
  • Page 35: Cpu

    The buzzer is driven when an alarm, etc. occurs. (9) DC Fan (SA Fan) A cooling fan for the “SA Ribbon Motor F”. When the temperature of the “SA Ribbon Motor F” exceeds a certain value, the fan starts to work. 2-21 CL-E700 series...
  • Page 36: Memory Map

    LCD Font Data (For downloading) (For CSA/CSE) 187DFFFFh 187E0000h Service Information (Backup) 187EFFFFh 187F0000h Service Information 187FFFFFh 18800000h Chinese Font (8M Bytes) 18FFFFFFh 20000000h Command RAM/Data RAM (Built-in CPU) 202FFFFFh 20300000h I/O (Built-in CPU) Reserved Area FFFFFFFFh 2-22 CL-E700 series...
  • Page 37: Sensors

    [SA Main PCB] H: Head Down Head Block Head Block "Up" position Photo- Interrupter SA Head Up Sensor PCB Head Block "Down" position Photo- Interrupter SA Head Up Sensor PCB (Head Up Sensor) SA Head Up Sensor PCB 2-23 CL-E700 series...
  • Page 38: Transparent Sensor (Sa Tra Sen Pcb) And Reflective Sensor (Sa Ref Sensor Pcb)

    When media runs out, since the light emitted from the LEDs directly falls on the transparent sensor continuously, media end can be detected. In this case, pin 96 (SNSTRA) of the CPU will go to “High” level. 2-24 CL-E700 series...
  • Page 39 95 (SNSREF). As to the current control of the LEDs, the operation is the same as for “Transparent sensor and reflective sensor (for detecting labels or U-shaped notches):” mentioned above. 2-25 CL-E700 series...
  • Page 40: Head Temperature Sensor

    To recover from the error status, turn OFF the printer once and then turn it A reference voltage, i.e., an allowable temperature limit, is applied to pin 2 of the comparator (U7A), while the sensor output voltage (TMPHD) from the head temperature sensor is applied 2-26 CL-E700 series...
  • Page 41: Pf Motor Temperature Sensor

    When the temperature of the “SA PF Motor” falls below 90  C (194  F), the LED and LCD returns to normal display, and printing automatically resumes. (Stops) Normal speed Normal speed Low speed 95°C 105°C 90°C Normal speed (Stop) (203°F) (Stop) (221°F) (194°F) 2-27 CL-E700 series...
  • Page 42 “Low” level. At this time, pin K1 (nTMPERR) is “Low” and the FPGA (U5) detects an abnormally high temperature. In this abnormal state, the printer stops +24V DC supply to the “SA PF Motor”. Also, it stops +24V DC supply to the “SA Head” and “SA Ribbon Motor F”. 2-28 CL-E700 series...
  • Page 43: Ribbon Motor Temperature Sensor

    ON. A reference voltage, i.e., an allowable temperature limit, is applied to pin 2 of the comparator (U8A), while the sensor output voltage (TMPRIB) from the ribbon motor temperature sensor is applied to pin 3. 2-29 CL-E700 series...
  • Page 44: Ribbon Tension Sensor (Sa Ribbon Sensor)

    At this time, the printer decreases the rotational speed of the “SA Ribbon Motor F” to give less tension to the ribbon. During printing, the above ribbon tension control cycle is repeated to give constand tension to the take-up side ribbon. Further, by using 2 photointerrupters, ribbon tension is finely controlled. 2-30 CL-E700 series...
  • Page 45: Ribbon Encoder Sensor

    [SA Main PCB] [SA Ribbon Encoder] * In power saving mode, +3VIO is not supplied. For details, refer to “2-2-6(1) Power supply circuit”. [Right side view] Ribbon Holder Ribbon Shaft Encoder Photointerrupter SA Ribbon Encoder (Ribbon Encoder Sensor) 2-31 CL-E700 series...
  • Page 46: Drivers

    OUT2A 11_D1 nPFENB 11_F1 ENABLE OUT2B nPFSLEEP 71_A12 SLEEP PFMS1 [SA PF Motor] MODE0 12_F2 PFMS2 13_F3 MODE1 Motor current control D/A Converter DAPFMT 82_B5 82_B4 C116 14_D4 A4984SES R2A20164SA +3.3V R165 81_A6 [SA Main PCB] DTC114TM 2-32 CL-E700 series...
  • Page 47: Ribbon Motor Driver

    Multivibrator [SA Ribbon Control PCB] RIBTRG P6_11 nRSTGA P8_12 74VHC123 nTMPERR From the following Temperature Sensors - Head Temperature Sensor Normally "High". - PF Motor Temperature Sensor [SA Main PCB] L: Error - Ribbon Motor Temperature Sensor 2-33 CL-E700 series...
  • Page 48 U11 goes to “High” level. As a result, pin 2 (ENABLE) of the motor driver (U601) goes to “High” level to stop its outputs for safety. This forcible function prevents the “SA Ribbon Motor F” from being damaged even if an abnormal condition happens. 2-34 CL-E700 series...
  • Page 49: Head Driver

    When driving: +24V +5.0V When checking: +5V 1-4,23-26 Buffer HDDAT3 HDDATA2 84_D8 HDDATA1 HDDAT2 83_C8 Thermal HDDAT1 HDDATA0 82_B8 Head nHDSTB nHDSTB 7,9,15 84_D6 HDCLK HDCLK 81_A8 nHDLAT nHDLAT 83_C6 5,6,8,11,12, 19,20,22 [SA Head] 74VHCT244 [SA Main PCB] 2-35 CL-E700 series...
  • Page 50: Buzzer Driver

    Buzzer will sound at the time of key operation or error occurrence. To sound the buzzer, the CPU (U1A) outputs a pulse from pin 137 (BUZZER). The transistor Q3 turns ON and OFF, and the buzzer sounds. +24V BUZZER P9_5 DTC114EM [SA Main PCB] 2-36 CL-E700 series...
  • Page 51: Fan Driver

    “SA Fan” does (While “SA Motor - While “SA Motor Ribbon F” not turn. Ribbon F” is running.) is running. 70  C 45  C - When “SA Motor Ribbon F” (158  F) (113  F) stops. 2-37 CL-E700 series...
  • Page 52: Other Circuits

    “Unit Power Supply” resumes +24V DC and the printer automatically returns to the normal mode. * By setting the “LCD Standby” of the “System Setup Menu” to ON, the LCD display turns off for further power saving when the printer enters the power saving mode. 2-38 CL-E700 series...
  • Page 53: Reset Circuit

    I/F circuits. +3.3V +3.3V L : Reset Voltage Detector nRST nRST nRSTGA [SA Main PCB] XC6119N28ANR-G Power ON nRSTIF +3.3V (To I/F circuits) +3.3V nRSTGA (To other circuits) FPGA nRST 21_R1 Reset nRSTV3 21_P1 2-39 CL-E700 series...
  • Page 54: Clock Circuit

    CPU generates a 384 MHz internal clock and 64 MHz bus clock. The 64MHz bus clock is fed to the FPGA (U5) and SDRAM (U4). System Clock (48MHz) Bus Clock USB_X1 (64MHz) FPGA USB_X2 48MHz BUSCLK CLK1 CKIO BUSCLK (To SDRAM) Internal Clock (384MHz) [SA Main PCB] 2-40 CL-E700 series...
  • Page 55: Ope-Pane Circuit

    LED/RED +5VIO DTC114TM LED1_R R209 Green (Power) R210 DTC114TM Red (Error) D201 [SA Main PCB] [SA Opepane PCB] * In power saving mode, +3VIO and +5VIO are not supplied. For details refer to “2-2-6(1) Power supply circuit”. 2-41 CL-E700 series...
  • Page 56: Usb I/F Control Circuit

    A certain voltage is applied when R109 a USB connector is connected. VBUSIN0 USBVBUS0 R113 VBUS0 C135 U15A DTC115TM R114 C136 BA2903SFVM C137 R115 C138 USB I/F VBUS USBDM0 USBDP0 SHLD Diode Array (Transient Voltage Supressor) [SA Main PCB] 2-42 CL-E700 series...
  • Page 57: Wired Lan I/F Circuit

    RXD0 LED0 ET_RXDV RXDV To/From ET_RXCLK U1A (CPU) ET_RXER RXER nETINTP INTRP ET_TXCLK ET_TXEN TXEN ET_TXD0 TXD0 ET_TXD1 TXD1 ET_TXD2 TXD2 R161 ET_TXD3 LED1 TXD3 ET_COL ET_CRS RJ45 Connector C170 C171 nRSTIF nRST [SA Main PCB] KSZ8081MNXCA 2-43 CL-E700 series...
  • Page 58: Option Board I/F Circuit (Option)

    U5 FPGA nACK/DTR ACK/DTR/pEP01 nFAULT FAULT/hINT SLCT SELECT/PPON0 DSWOUT DWSWOT IFTXD/SO/DIR TXD/SO/DIR IFRXD/SI RXD/SI IFSCLK SCLK nRSTIF RESET To/From USBDP1 USB_D+ U1A CPU USBDM1 USB_D- VBUS Diode Array 33-38,40 (Transient Voltage Supressor) USBVBUS1 C127 C128 [SA Main PCB] 2-44 CL-E700 series...
  • Page 59: Peeler Circuit (For Optional Peeler)

    CPTYP1 J301 74_D9 OPTION_TYPE1 +3.3V CPRTYP1 +5VIO +5VIO D3 R69 PEELER SENS SNSPEEL PEELSENS [SA Relay PCB] [SA Main PCB] * In power saving mode, +5VIO is not supplied. For details refer to “2-2-6(1) Power supply circuit”. 2-45 CL-E700 series...
  • Page 60: Cutter Control Circuit (For Optional Cutter)

    L: When Cutter is installed. CPRTYP0 8,9,10 CPTYP0 74_D12 CPTYP1 74_D9 (from the Peeler) [SA Relay PCB] TMPCUT TEMP ERROR Detection +3.3V +3.3V FPGA TMPENB_CUT 71_A15 TMPCUT BA2903SFVM nTMPERR 21_K1 Error: Low [SA Main PCB] nTMPERR (L: Disables ribbon motor drive.) 2-46 CL-E700 series...
  • Page 61 U8B goes to “Low” level. At this time, pin K1 (nTMPERR) is “Low” and the FPGA detects an abnormally high temperature. In this abnormal state, the printer stops +24V DC (VMT) supply to the cutter. Also it stops +24V DC supply to the “SA Head”, “SA PF Motor” and “SA Ribbon Motor F”. 2-47 CL-E700 series...
  • Page 62: Operation Panel

    In the case of continuous media, it is fed by a certain distance and then stops. • When “TEAR OFF” setting is enabled, media is fed to TEAR OFF position and stops there. 2-48 CL-E700 series...
  • Page 63 Once you have set to “Repeat Last One”, pressing the [MENU] key reissues the last label. However, in this case, to enter menu setup mode, you need to press and hold the [MENU] key for more than 4 seconds. 2-49 CL-E700 series...
  • Page 64: Test Mode

    The printer enters self print mode for self test printing, and then stops after printing. 3. To repeat self test printing, press the [FEED] ( ) key again. To exit from self print mode: Turn off the power. 2-50 CL-E700 series...
  • Page 65: Hex Dump Mode

    02 40 30 31 30 30 0D 02 60 30 30 32 30 0D 02 4C .M0100..c0020..L 44 31 31 0D 31 30 30 30 30 30 30 30 30 30 31 30 D11.100000000010 30 30 31 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 0010123456789:;< 2-51 CL-E700 series...
  • Page 66: Menu List Print Mode

    Then the printer enters menu setup mode for further menu operation. To exit from menu list print mode: In Main menu, press the [PAUSE] ( ) key twice. Machine Information Note: Citizen continually enhances its Model Number : CL-E720 Serial Number : **-*******...
  • Page 67 IPv6 : On [Option Interface Menu] RS-232C Baud rate : 9600 bps RS-232C Parity : None RS-232C Length : 8 bit RS-232C Stop bit : 1 bit RS-232C X-ON : Yes  <Example of Datamax emulation selected> 2-53 CL-E700 series...
  • Page 68: Factory/Service Mode

    Returns to previous item, or the value is incremented/changed. [MENU] Goes to the next item, or the value is decremented/changed. [PAUSE] ( ) Resets the printer, or exits from the current menu. ■ [STOP] ( Acts as the Enter key. 2-54 CL-E700 series...
  • Page 69 [MENU] Interface MENU [MENU] ■ STOP ( Option Interface [MENU] FEED ( Machine Info PAUSE ( ) [MENU] Test Mode [MENU] Global Config To exit from Factory/Service mode: In main menu, press the [PAUSE] ( ) key. 2-55 CL-E700 series...
  • Page 70: How To Print The Factory Mode Settings Menus

    ) key to print the configuration settings. The current factory mode setting values are printed. To exit from menu mode: Press the [PAUSE] ( ) key several times until the printer exits from the “Test Mode” main menu. 2-56 CL-E700 series...
  • Page 71: Machine Information

    Chapter 2 Operating Principles 2-3. Operation Panel [Print sample] Machine Information Note: Citizen continually enhances its Model Number : CL-E720 Serial Number : **-******* printers with new options and Boot Version : *.* settings based on our customer’s ROM Version...
  • Page 72 IPv6 : On [Option Interface Menu] RS-232C Baud rate : 9600 bps RS-232C Parity : None RS-232C Length : 8 bit RS-232C Stop bit : 1 bit RS-232C X-ON : Yes  <Example of Datamax emulation selected> 2-58 CL-E700 series...
  • Page 73: How To Change The Settings In Factory Mode

    (-32 to +32 mm, -1.26 to +1.26 inches) (Option) Mach Peel Pos -256 to +256dot Electrically shifts the peel position back and [Machine Peel Position] (+000 dot) forth. (-32 to +32 mm, -1.26 to +1.26 inches) (Option) 2-59 CL-E700 series...
  • Page 74 TT Hot HeatRate -1.0 to +1.0% In TT (Thermal Transfer) mode, adjusts the head [TT Hot HeatRate Adjust] (0.0%) temperature compensation coefficient for the head temperature 25C (77F) and higher. To increase the print darkness, increase the value. 2-60 CL-E700 series...
  • Page 75 0 to 9999999 Designates the length where a head cleaning [Head Clean Message] (0000000m) message is to be printed. Print Prefer Darkness/Speed To put the priority on printing density or printing [Printer Preference] (Darkness) speed is selectable. 2-61 CL-E700 series...
  • Page 76: Setting Submenu In Factory Mode

    7. Press the [PAUSE] ( ) key to return to “Factory Setup” menu. (To set other submenu, repeat from Step 2.) 8. Press the [PAUSE] ( ) key once again. The changed value is stored in the printer and the printer restarts internally. Then, the printer returns to normal operation. 2-62 CL-E700 series...
  • Page 77: How To Operate Submenus In Service Mode

    0123.456Km ■ To clear the service counter, press the [STOP] ( key. Cut Counter Displays the cut count since you reset it last. Example: Count ■ To clear the cut counter, press the [STOP] ( ) key. 2-63 CL-E700 series...
  • Page 78: Submenu Operation In Service Mode

    Then, the “SA PF Motor” turns to feed media forward or backward. (The ■ “SA PF Motor” turns each time you press the [STOP] ( ) key.) [When selecting “Head Check”] [When selecting “Motor Feed”] Feed Feed  PASS    Start Back 0000dots 2-64 CL-E700 series...
  • Page 79 ) key to execute resetting. Length 0000.000 km 7. Press the [PAUSE] ( ) key twice to return to “Service Mode” main menu. 8. To check other submenu, repeat from Step 3. Otherwise, turn off the power to terminate Factory/Service mode. 2-65 CL-E700 series...
  • Page 80: Interface

    Application layer: DHCP, HTTP, SNMP, Raw Socket Port Connector RJ-45 (2) Signal line and pin arrangement Pin No. Signal name Function Send (+) Send (-) Receive (+) Not used. Not used. Receive (-) Not used. Not used. 2-66 CL-E700 series...
  • Page 81: Serial Interface (Option)

    SGND Signal ground Signal grounding line 8-13, Not used 15-19 (Factory use only ) Data Terminal Signal line that is active when the printer can Ready interface with the host 21-25 Not used  2-67 CL-E700 series...
  • Page 82: Protocol

    DTR turns to “Low (Busy)” in the following conditions: • When the printer is in off-line mode. • When the remaining buffer is less than 128 bytes. (After DTR becomes “Low”, DTR retains “Low” until the remaining buffer becomes 1024 bytes or more.) 2-68 CL-E700 series...
  • Page 83: Parallel Interface (Option)

    Peripheral logic high (Pulled up to +5V at 10K resister.) 19-30 Ground for twisted pair return PRIME Input Printer reset FAULT Output Signal specifying printer error Signal ground Not used Pulled up to +5V at 10K resistor. SELECTIN Input Invalid (ignored) 2-69 CL-E700 series...
  • Page 84: Parallel Port Status Signals When An Error Occurs

    • Other Select: H  L Fault: Conditions for Busy • Receive buffer full • Data being read • Error  (4) Compatible timing specification [When power is on] (Timing to go on-line) Power On Reset BUSY SELECT 2-70 CL-E700 series...
  • Page 85 [While receiving PRIME signal] 10~15µsec or more PRIME BUSY Fault SELECT Note: If the PRIME signal width is 10 µsec or less, it is not accepted. BUSY goes to “High” when the PRIME signal is accepted by the printer. 2-71 CL-E700 series...
  • Page 86 Chapter 2 Operating Principles 2-4. Interface [Timing relationship between BUSY and ACK] Center BUSY About 2 µsec 2-72 CL-E700 series...
  • Page 87 Chapter 3 Disassembly and Maintenance HAPTER ISASSEMBLY AND AINTENANCE CL-E700 series...
  • Page 88 Plate Holder Paper L ................3-29 3-6-15. “SA Power SW Cable” and “Frame Bottom”............ 3-30 3-6-16. SA Platen......................3-31 3-6-17. “SA Head Up Sensor PCB”, “SA TRA Sen PCB”, “FFC TRA Sensor” and “Leaf Adjust Sensor U” ..................3-32 CL-E700 series...
  • Page 89 Front side “Cam Tension Base Adjust” position adjustment (For service personnel).............. 3-58 (2-2) Rear side “Cam Tension Base Adjust” position adjustment (For user) ................... 3-58 Ribbon guide position adjustment (with a part of the “SA Head”) ... 3-60 CL-E700 series...
  • Page 90: Maintenance Precautions

    • Do not put the printed circuit boards directly on the printer or on the floor. • When disassembling or reassembling, check wires for any damage and do not pinch or damage them. Also, run wires as they were. CL-E700 series...
  • Page 91: Cleaning

    • FLOIL G-474C (by Kanto Chemical Co., Ltd.) 3-3-3. Quantity of lubricant Small quantity.. ..... About 1 drop. Ordinary quantity .. ..About 3 to 4 drops. About 0.2 mm thick for grease. Large quantity.. ..Apply sufficiently. CL-E700 series...
  • Page 92: Maintenance Tools List

    Phillips Screwdriver Bit: #0, #1, #2 (Length 200mm) Phillips Screwdriver Bit: #0, #1, #2 (Length 100mm) Flat-blade Screwdriver 4.3 mm width Box wrench Box size: 5 mm Tweezers Round Nose Pliers Cutting Nippers Soldering Iron (30W) Volt-ohm Meter CL-E700 series...
  • Page 93: Quick Detachment Of Major Parts

    • The “SA Cover Frame” has two bosses that allow easy positioning of the “SA Head”. When mounting the “SA Head” with the 1 screw (BH M3.0x6 (NI)) (), be sure that it is securely engaged with the bosses. CL-E700 series...
  • Page 94: Sa Platen

    “SA Platen” by lifting it upwardly. "SA Top Cover" Block Head Block SA Platen Note on reassembling: • After mounting the “SA Platen”, be sure that it is securely engaged with the main body. CL-E700 series...
  • Page 95: Sa Ribbon Tension Unit R

    “Spring Ribbon Return R”. 5. Mount the “SA2 Ribbon Unit Fan” with the 3 screws (BH M3.0x4 (NI)). CL-E700 series...
  • Page 96: Disassembly, Reassembly And Lubrication

    Chapter 3 Disassembly and Maintenance 3-6. Disassembly, Reassembly and Lubrication 3-6. Disassembly, Reassembly and Lubrication [Disassembly Flowchart for Major Parts] CL-E700 series (See 3-5-1.) SA Head (See 3-5-2.) SA Platen (See 3-5-3.) SA Ribbon Tension Unit R (See 3-6-1.) “SA Top Cover” Block (“SA Top Cover”...
  • Page 97 • Cam Head Adjust • Cam Head Balance SA PF Motor (See 3-6-20.) • SA Ref Sensor PCB (See 3-6-21.) • Spring Adjust Sensor L • Platen Drive Gears (See 3-6-22.) • Lever Head Lock • Frames • Plate Peeler CL-E700 series...
  • Page 98: Sa Top Cover" Block

    1. Remove the 2 screws (BH M3.0x8D) and detach the “Cover Front Top” in the direction shown by the arrow. 2. Remove the “Logo Citizen L” from the “Cover Front Top”. 3. Remove the “Cover Window” from the “SA Top Cover”.
  • Page 99: Unit Ribbon

    Therefore, a ribbon wrinkle may not be removed with the Ribbon Left-Right Balance Adjustment Knob, as expected. Unit Ribbon SA Ribbon Frame (with Support) Forbidden 4 Screws Forbidden 5 Screws DO NOT LOOSEN. DO NOT LOOSEN. Ribbon Left-Right Balance Adjustment Knob CL-E700 series...
  • Page 100 DO NOT LOOSEN. Forbidden Screws 5 J304 Unit Ribbon Cover PF Motor 2 BH M3.0x5K (SA Relay PCB) Cover PF Motor Head Block Note on reassembling: • Mount the “Cover PF Motor 2” () with the Head Block opened. 3-14 CL-E700 series...
  • Page 101: Unit Ribbon" Covers

    3. Disconnect the connector J604 from the main body. BH M3.0x4 (NI) SA2 Ribbon Unit Fan Cover Ribbon Gear J604 BH M3.0x4 (NI) Note on reassembling: • When mounting the “SA2 Ribbon Unit Fan”, pay attention so as not to pinch the cable of J604. CL-E700 series...
  • Page 102: Sa Fan" Of The "Unit Ribbon

    Cover Ribbon Motor SA Fan Groove (Pass here.) Plate Fan BHT (#2) M3.0x6 (NI) J604 Note on reassembling: • Referring to the magnified view, insert the cable of the “SA Fan” into the groove indicated by a circle. 3-16 CL-E700 series...
  • Page 103: Sa Ribbon Tension Unit R", "Sa Ribbon Encoder" And Ribbon Gears

    To correctly hook them, refer to “3-5-3 SA Ribbon Tension Unit R”. After hooking both ends, rotate the “SA Ribbon Tension Unit R” () right and left to be sure that it returns to the original position by the spring force. CL-E700 series...
  • Page 104: Ribbon Gears

    • Assemble the “SA Holder R Shaft”, “Spring Ribbon Return” and “Gear 5F Ribbon” as shown below. Spring Ribbon Return SA Holder R Shaft Gear 5F Ribbon  • Apply FLOIL G-474C to the gears and the shafts marked with “ ”. Refer to the figure on the previous page. 3-18 CL-E700 series...
  • Page 105: Sa Ribbon Motor F" And "Sa Ribbon Control Pcb

    1. Remove the 4 screws (BH M3.0x3 (NI)) and detach the “Catch Ribbon Holder” (2 pcs.). 2. Remove the 2 screws (PHT(#2) M3.0x8 (NI)) and detach the “Knob Ribbon Unit”. PHT(#2) M3.0x8 (NI) BH M3.0x3 (NI) Catch Ribbon Holder Knob Ribbon Unit BH M3.0x3 (NI) CL-E700 series...
  • Page 106: Plate Ribbon Guide Roller" Block

    Base Adjust” with the scribe line as shown below. (The “Cam Tension Base Adjust” is set to the mechanical center.) Next, perform the adjustment according to “3-7-2(2-2) Rear side “Cam Tension Base Adjust” position adjustment (For user)”. Scribe line Cam Tension Base Adjust 3-20 CL-E700 series...
  • Page 107: Sa Ribbon Tension Shaft F" And "Sa Ribbon Sensor

    • Pass the connector J606 through the hole “A” in the frame. • When remounting the “Ribbon Sensor Frame F” Block, perform the ribbon slant elimination adjustment. Refer to “3-7-2(1) Ribbon Left-Right Balance Adjustment Knob (For user)”. • Once the label is peeled off, it cannot be reused. CL-E700 series...
  • Page 108: Sa Ribbon Tension Shaft F" And "Sa Ribbon Sensor

    (The “Cam Tension Base Adjust” is set to the mechanical center.) Next, perform the adjustment according to “3-7-2(2-1) Cam Tension Base Adjust Front side “Cam Tension Base Adjust” position adjustment (For service personnel)”. 3-22 CL-E700 series...
  • Page 109: Sa Opepane Pcb

    Cover”. 4. Remove the “Sheet Ope-Pane” and “Cover LCD” from the “Cover Ope-Pane”. Holder Ope-Pane Cover BH PT M2.0x8 NO.0PH (4-0.3) M2.0x3 (NI) Spacer Screw SA Opepane PCB Sheet Ope-Pane Cover LCD Key Ope-Pane Window LED Cover Ope-Pane CL-E700 series...
  • Page 110: Case

    4. Remove the 1 screw (BH M3.0x5K) and 2 screws (BH M3.0x4 (NI)), slide the “Cover Steel L” backward (), and then detach it by lifting upwardly (). BH M3.0x4 (NI) Case BH M3.0x5K BH M3.0x4 (NI) Cover Steel L 3-24 CL-E700 series...
  • Page 111: Sa Main Pcb" And "Sa Relay Pcb

    2. Disconnect the “SA Relay Cable” from the “SA Relay PCB”. 3. Remove the 4 screws (BH M3.0x4 (NI)) and detach the “SA Relay PCB”. BH M3.0x4 (NI) "SA Main PCB" Block BH M3.0x5K J301 SA Relay Cable FFC Opepane BH M3.0x4 (NI) SA Relay PCB CL-E700 series...
  • Page 112 SA Main PCB Plate I/F Cover Plate Main PCB Note on reassembling: • When the “SA Main PCB” is replaced with a new one, be sure to perform the transparent/reflective sensor adjustment. Refer to “3-7-1 Transparent/Reflective Sensor Adjustment”. 3-26 CL-E700 series...
  • Page 113: Unit Mechanism

    At this time, be sure that the part “A” of the “Frame Relay PCB” is correctly placed on the foot of the “Unit Mechanism”. [FRONT] Align. Label Mark CL-E700 series...
  • Page 114: Unit Power Supply" And "Paper Holder" Block

    10. Remove the 2 screws (BH M3.0x4 (NI)) and detach the “Plate Holder Paper R” from the bottom frame. BH M3.0x4 (NI) BH M3.0x4 (NI) BH M3.0x4 (NI) "Paper Holder" Block Frame Mechanism Plate Holder Paper R SA Power Cable BH M3.0x4 (NI) BH M3.0x4 (NI) "Unit Power Supply" Block AC Input Connector 3-28 CL-E700 series...
  • Page 115: Unit Power Supply

    1. Remove the 3 screws (BH M3.0x4 (NI)) and detach the “Cover Lever”. 2. Remove the “SA Damper Shaft” and “Spring Damper” (2 pcs.) from the “Plate Holder Paper L”. BH M3.0x4 (NI) Cover Lever Spring Damper SA Damper Shaft Spring Damper Plate Holder Paper L CL-E700 series...
  • Page 116: Sa Power Sw Cable" And "Frame Bottom

    BH M3.0x5K BH M3.0x4 Plate Hinge L (NI) Ferrite Core Label FCC PH (SW+PW) ICES VCCI-A M4x6 Label Caution Plate Hinge R Frame Bottom Label Rating BH M3.0x5K Ferrite Core BH M3.0x4 (NI) BH M3.0x8 Cover Steel R 3-30 CL-E700 series...
  • Page 117: Sa Platen

    1. Open the Head Block. 2. While pressing the part “A” of the “SA Platen”, raise its right end by about the indicated degrees. 3. Remove the “SA Platen” by lifting it upwardly. Head Block SA Platen Unit Mechanism CL-E700 series...
  • Page 118: Unit Sensor U" And "Sa Head Up Sensor Pcb

    BH M2.0x4 (NI) Unit Sensor U A’ B’ Notes on reassembling: • When mounting the “Unit Sensor U” (), insert its projections “A” and “B” into the corresponding holes “A’ ” and “B’ ” in the main body. 3-32 CL-E700 series...
  • Page 119: Sa Tra Sen Pcb

    If it is inserted upside down, the circuit is not electrically connected. • When the “SA TRA Sen PCB” is replaced with a new one, be sure to perform the sensor adjustment. Refer to “3-7-1 Transparent/Reflective Sensor Adjustment”. CL-E700 series...
  • Page 120: Ffc Tra Sensor" And "Leaf Adjust Sensor U

    FFC TRA Sensor Tape Sensor Cable U Leaf Adjust Sensor U Spring Sensor Frame NO.0 TFH (PT4-0.5) M2.0x4 NO1 PHT M2.0x8 (NI) 2x5x0.3 (NI) BH M3.0x6 (NI) Cap Sensor Frame L Cap Sensor Frame R Plate Sensor Holder U 3-34 CL-E700 series...
  • Page 121 • Run the “FFC TRA Sensor” () as shown below. Pass it through the two slits (“A” and “B”) and the hook part. FFC TRA Sensor Cap Sensor Cable U Hook Slit "A" Slit "B" [Bottom View] [Bottom View] CL-E700 series...
  • Page 122 Wire” (), and then hook the short end of the spring on the part “C” of the “Holder Sensor U” Block. Fixing the "Spring Sensor Frame" (Shorter slit) Cable wire for pulling Cover Head Wire "Holder Sensor U" Block Spring Sensor Frame 3-36 CL-E700 series...
  • Page 123: Unit Head" And "Unit Pf

    D: 3 surfaces on the “Shaft Head Holder” (). Hooks for “Spring Head Up” () and “Spring2 Head Up” () (4 places) • When mounting the “Shaft Head Holder” (), be sure that its mounting direction is correct. CL-E700 series...
  • Page 124 (This can prevent unwanted noise that might occur when the “Unit Head” () is opened or closed.) Hook the “Spring2 Head Up” () so that its hook parts direct as shown below. Hook parts Spring Head Up Spring2 Head Up Thin Thick Hook parts 3-38 CL-E700 series...
  • Page 125: Sa Head", "Cam Head Adjust" And "Cam Head Balance

    (NI) and BH M3.0x6 (NI)), and remove the “SA Head Cable”. BH M3.0x6 (NI) SA Head Cable BH M3.0x3 (NI) BH M3.0x6 (NI) Guide Head Cable "SA Head" Block "5" (Media Width Adjustment Dial) Unit Head "5" (Media Thickness Adjusment Dial) CL-E700 series...
  • Page 126 4. After mounting the “SA Head” Block, set the Media width adjustment dial to “5” to give tension to the “SA Head” Block. Claw "SA Head" Block "0" (Media Width Adjustment Dial) Screw "9" to "5" (Media Thickness Adjusment Dial) Slit 3-40 CL-E700 series...
  • Page 127: Sa Head" And "Cam Head Adjust

    Spring Head Holder Sheet Cable Protect "Cam Head Adjust" Block Lever Head Adjust2 NO1 PHT M2.0x6 (NI) SA Lever Head Adjust 2 2x5x0.3 (NI) Spring Adjust Cam Cam Head Adjust Guide Head Adjust Spring 3x8x0.5 PHT (#2) M3.0x8 (NI) CL-E700 series...
  • Page 128 • After assembling the “SA Head”, perform test print in self print mode to check the print quality. (Refer to “2-3-2(1) Self print mode”.) If the print quality is not enough, ribbon slanting or ribbon wrinkle may occur. In this case, perform “3-7-2 Ribbon Slant Elimination Adjustment”. 3-42 CL-E700 series...
  • Page 129: Cam Head Balance

    Label Head Adjust Notes on reassembling:  • Apply FLOIL G-311S to the following parts marked with “ ”. Pivot Head Balance Cam: Surface Cam Head Balance: Cam portion • Once the label is peeled off, it cannot be reused. CL-E700 series...
  • Page 130: Sa Pf Motor

    (with Thermistor)” so that its letter “C” is located on the connector side of the “SA PF Motor (with Thermistor)”. • Mount the “SA PF Motor (with Thermistor)” on the frame so that its connector faces the front. 3-44 CL-E700 series...
  • Page 131: Sa Ref Sensor Pcb" And "Spring Adjust Sensor L

    NoO PH(4-0.3) M2x3 (NI) SA Ref Sensor PCB Guide Paper Set NO.0 PHT(BT#1) M2.0x3 Spring Friction Sen PG SA Ref Sensor Cable Plate Friction PG Spring Adjust Sensor L Shaft Sensor Guide Wire Tie BH M3.0x4 (NI) Holder Guide Sensor L CL-E700 series...
  • Page 132 Press straight down. Holder Adjust Sensor L Slit Spring Adjust Sensor L • When the “SA Ref Sensor PCB” is replaced with a new one, be sure to perform the sensor adjustment. Refer to “3-7-1 Transparent/Reflective Sensor Adjustment”. 3-46 CL-E700 series...
  • Page 133: Platen Drive Gears

    Gear PF Idle Gear PF 2 5.2x10x0.25 E-Ring 4.0 Notes on reassembling:  • Apply FLOIL G-311S to each gears and shafts marked with “ ”. • The gears have their own orientation except the “Gear PF Idle”. CL-E700 series...
  • Page 134: Lever Head Lock" And "Sa Main Plate R

    “Lever Head Lock”, and insert the other end into the hole in the “SA Main Plate R”. Also, mount the “Lever Head Lock” on the “SA Main Plate R” as shown below. Then, be sure that the lever moves smoothly. Lever Head Lock 3-48 CL-E700 series...
  • Page 135: Frame Main", "Sa Main Plate L" And "Plate Peeler

    • Stick the “Label Mark” so that its mark is aligned with the media guide end of the “Cover Head Wire” (a part of the “Unit Mechanism”). Plate Holder Paper L Cover Head Wire Unit Mechanism [FRONT] Label Mark Align. CL-E700 series...
  • Page 136: Adjustments

    “3-7-1(2-1) “Init Thru Sen” • SA Ref Sensor PCB (Reflective sensor) sensitivity adjustment” • SA Main PCB Init Refl Sen • SA Ref Sensor PCB (Reflective sensor) “3-7-1(2-2) Init Refl Sen • SA Main PCB sensitivity adjustment” 3-50 CL-E700 series...
  • Page 137: Init Thru Sen" Sensitivity Adjustment

    3. Be sure that the first submenu “Init Thru Sen” is displayed. Factory Setup   Init Thru Sen ■ 4. Press the [STOP] ( ) key to enter “Init Thru Sen” sensitivity adjustment mode. Init Thru Sen   CL-E700 series...
  • Page 138 10. Press the [PAUSE] ( ) key to return to “Factory Setup” menu. 11. Press the [PAUSE] ( ) key once again. The changed value is saved in the printer and the printer is restarted internally. Then, the printer returns to normal operation. 3-52 CL-E700 series...
  • Page 139: Init Refl Sen Sensitivity Adjustment

    1. Prepare recommended tag media or tag media to be used. 2. Correctly put the tag media (or continuous tag media) on the “SA Ref Sensor PCB” (Reflective sensor). In this case, keep away the black mark from the “SA Ref Sensor PCB”. 3. Close the Head Block. CL-E700 series...
  • Page 140 Adjustment starts and the following screen is display. Now !!   Executing 7. Be sure that adjustment is successfully completed and the following screen is displayed. (The value “123” is an example.) Finished   DAC 123 3-54 CL-E700 series...
  • Page 141 9. Press the [PAUSE] ( ) key twice to return to “Factory Setup” menu. 10. Press the [PAUSE] ( ) key once again. The changed value is saved in the printer and the printer is restarted internally. Then, the printer returns to normal operation. CL-E700 series...
  • Page 142: Ribbon Slant Elimination Adjustment

    • When the “Ribbon Sensor Frame F” Block () is replaced or reassembled. 1. Set the Ribbon Left-Right Balance Adjustment Knob to the center of the scale. 2. Turn the Ribbon Left-Right Balance Adjustment Knob to eliminate ribbon wrinkles. 3-56 CL-E700 series...
  • Page 143: Cam Tension Base Adjust" Position Adjustment

    Guide Roller” Block () rotates vertically in a limited range. With this rotation, ribbon slant can be eliminated. Ribbon Cam Tension Base Adjust (Rear side) Cam Tension Base Adjust "Plate Ribbon Guide Roller" Block (Front side) 2 "Ribbon Sensor Frame F" Block Ribbon Left-Right Balance Adjustment Knob CL-E700 series...
  • Page 144: Front Side "Cam Tension Base Adjust" Position Adjustment (For Service Personnel)

    If the left side ribbon wrinkles cannot Mechanical center be eliminated viewing from the rear. be eliminated viewing from the rear. Base (Rear side view) Cam Tension (SA Ribbon Frame) Base Adjust Supporting point "Plate Ribbon Guide Roller" Block Center 3-58 CL-E700 series...
  • Page 145 “Cam Tension Base Adjust”.) [In the case of front side] Cam Tension Base Adjust Part of the "Ribbon Sensor Frame F" Block (movable part) b’ b’ a’ a’ c’ SA Ribbon Frame (fixed part) CL-E700 series...
  • Page 146: Ribbon Guide Position Adjustment (With A Part Of The "Sa Head")

    Loosen (do not remove) the screws “A” and “B”. Shift the left end of the “Shaft Ribbon Guide” back and forth to move the ribbon contacting surface. [Top view] (supporting point) [Right side view] Shaft Ribbon Guide Ribbon 3-60 CL-E700 series...
  • Page 147 SA Ribbon Tension Unit R Weak Tension Strong Ribbon Cam Tension Base Adjust Cam Tension Base Adjust (Rear side) (Front side) Ribbon Left-Right Balance Adjustment Knob Shaft Ribbon Guide (A part of the "SA Head") [Adjustment locations for eliminating ribbon wrinkles] CL-E700 series...
  • Page 148 * By setting the number to a larger one i.e., by giving a stronger tension to the ribbon, wrinkles tend to be reduced. 4. Proceed to the next item. Parallel Pin (Dial) SA Ribbon Tension Unit R Weak Tension Strong Ribbon 3-62 CL-E700 series...
  • Page 149 2. Perform ribbon guide adjustment to eliminate ribbon wrinkles, as required. Refer to “3-7-2(3) Ribbon guide position adjustment (with a part of the “SA Head”)”. 4. Proceed to the next item. b’ Ribbon a’ A’ Ribbon Left-Right Balance A’ Adjustment Knob CL-E700 series...
  • Page 150 “3-7-2(2) “Cam Tension Base Adjust” position adjustment” and perform adjustment according to “3-7-2(2-2) Rear side “Cam Tension Base Adjust” position adjustment (For user)”. When adjustment is done on the rear side, repeat above “(3) Adjustment on the front side” again. 3-64 CL-E700 series...
  • Page 151 Chapter 4 Troubleshooting HAPTER ROUBLESHOOTING CL-E700 series...
  • Page 152 4-2-1. Problems in Powering Up the Printer ..............4-5 4-2-2. Media-feed Problems ..................4-6 4-2-3. Problems in Printing ................... 4-7 4-2-4. Ribbon-feed Problem ..................4-9 4-2-5. Sensor Problems....................4-11 4-2-6. Operation Panel Problems ................. 4-14 4-2-7. Connector Location .................... 4-15 CL-E700 series...
  • Page 153: Error Message And Corrective Actions

    Enter sensor adjustment mode by turning ON while pressing and holding [MENU], [FEED] ( ) and ■ [STOP] ( ) keys. Then perform sensor adjustment. For details, refer to “2-3-3(3) How to change the settings in Factory mode” in Chapter 2. CL-E700 series...
  • Page 154 • Power to the “SA Head”, “SA PF Motor” and “SA System Fail Ribbon Motor F” is shut off. (To resume, turn the power OFF and then ON.) Auto-cutter abnormality (foreign object etc.) Flashing in red Error (Option) Cutter Fail • Jamming, etc. CL-E700 series...
  • Page 155: Troubleshooting

    If it is not connect or is inserted upside down, no LED lights even if you turned ON the power. Also, nothing is displayed on the LCD. 5. Failure in the power supply circuit. 5. Replace the “Unit Power Supply”. CL-E700 series...
  • Page 156: Media-Feed Problems

    1. Set media correctly. 2. Is the media being used within 2. Use media within manufacturer's manufacturer's specifications? specifications. 3. Check the media feed mechanism and 3. Remove dust or foreign matter. media path for dust or other foreign matter. CL-E700 series...
  • Page 157: Problems In Printing

    [Bottom right of the “SA Main PCB”] 6. Replace the “SA Head”. 6. “SA Head” is broken. 7. Failure in the head driver circuit. 7. Replace the “SA Head”. 8. Failure in the control circuit. 8. Replace the “SA Main PCB”. CL-E700 series...
  • Page 158 Uneven printing density may be observed either on the right side or the used. left side. 2. Is the printing density set to an optimal 2. Adjust the printing density. condition? CL-E700 series...
  • Page 159 11. Does the “SA Ribbon Motor F” turn correctly? 12. Failure in the ribbon motor drive circuit. 12. Replace the “SA Ribbon Control PCB”. 13. Failure in the ribbon motor control 13. Replace the “SA Relay PCB” or circuit. “SA Main PCB”. CL-E700 series...
  • Page 160 Shaft F” or the “SA Ribbon from contacting with the Sensor”. photointerrupters of the “SA Ribbon Sensor”? (Push the “SA Ribbon Tension Shaft F” by hand and check if it moves smoothly. For its operation, refer to “2-1-4. Ribbon Feed Mechanism”.) 4-10 CL-E700 series...
  • Page 161: Sensor Problems

    “SA Ribbon Encoder”? 4. Failure in the ribbon encoder sensor? 4. Replace the “SA Ribbon Encoder”. 5. Failure in the control circuit. 5. Replace the “SA Ribbon Control PCB”, “SA Relay PCB”, or “SA Main PCB”. 4-11 CL-E700 series...
  • Page 162 “SA Ref Sensor PCB” to remove dust. 6. Replace the “SA Ref Sensor PCB”. 6. Failure in the reflective sensor. 7. Failure in the control circuit. 7. Replace the “SA Main PCB”. 4-12 CL-E700 series...
  • Page 163 * If the adjustment ends abnormally (adjustment impossible), the LED flashes in red and “Failed” is displayed on the LCD. ■ 4. Press the [STOP] ( ) key. Then the printer internally restarts, and then enters the normal operation. 4-13 CL-E700 series...
  • Page 164: Operation Panel Problems

    3. Is the “FFC Opepane” inserted upside 3. Connect it in the right orientation. down? 4. Failure in the “SA Opepane PCB”. 4. Replace the “SA Opepane PCB”. 5. Failure in the control circuit. 5. Replace the “SA Main PCB”. 4-14 CL-E700 series...
  • Page 165: Connector Location

    To SA Head Ethernet To Unit Power Supply Front To SA PF Motor [SA Relay PCB] To Peeler (Optional) To Cutter (Optional) J302 J303 J304 J301 To SA Ribbon Control PCB To SA Main PCB SA Relay PCB Front 4-15 CL-E700 series...
  • Page 166 To SA Ribbon Encoder To SA Fan J604 J603 J605 To the thermistor of the SA Ribbon Control PCB SA Motor Ribbon J602 J601 To SA Motor Ribbon J606 To SA Ribbon Sensor To SA Relay PCB Front 4-16 CL-E700 series...
  • Page 167 Chapter 5 Parts Lists HAPTER ARTS ISTS CL-E700 series...
  • Page 168 Parts List & Location for Unit Opepane ............5-28 Drawing No. 8 Parts List & Location for Unit Ribbon ............... 5-31 Drawing No. 9 Parts List & Location for SA2 Ribbon Unit Fan ..........5-36 Drawing No. 10 Parts List & Location for Accessories ............... 5-39 CL-E700 series...
  • Page 169: Recommended Spare Parts List

    Chapter 5 Parts Lists CL-E700 series Recommended Spare Parts List Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 CL-E700 series...
  • Page 170 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Recommended Spare Parts List Sheet No. 1/1 Rev. No. 0 Item Q'ty/ Maint. Class Remarks Location Part No. Part Name Unit Worn Casual PWT20011-0 Unit Power Supply 2-13-1 PPS00152-0 SA Main PCB (200ENG)
  • Page 171: Drawing No. 1

    Chapter 5 Parts Lists CL-E700 series Drawing No. 1 Parts List & Location for General Assembly Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 CL-E700 series...
  • Page 172 Chapter 5 Parts Lists DRAWING NO. 1 General Assembly (Rev. 0) (DRAW NO. 8) (DRAW NO. 7) CL-E700 series...
  • Page 173 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: General Assembly Sheet No. 1/2 Drawing No. 1 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit SA Ribbon Holder JM34710-1 Unit Ribbon (Ref. Drawing No. 8) Cover PF Motor 2...
  • Page 174 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: General Assembly Sheet No. 2/2 Drawing No. 1 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 1-21 Cover Steel L PAA00006-0 FFC Op panel PSS40015-0 PPN30005-0 Unit Op panel (Ref.
  • Page 175: Drawing No. 2

    Chapter 5 Parts Lists CL-E700 series Drawing No. 2 Parts List & Location for Unit Base Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 CL-E700 series...
  • Page 176 Chapter 5 Parts Lists DRAWING NO. 2 Unit Base (Rev. 0) 13-1 13-2 13-3 (DRAW NO. 3) 5-10 CL-E700 series...
  • Page 177 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Base Sheet No. 1/2 Drawing No. 2 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit Unit Mechanism (Ref. Drawing No. 3) Frame Mechanism PAC60059-0 SA Relay PCB...
  • Page 178 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Base Sheet No. 2/2 Drawing No. 2 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 2-19 Screw BH M3.0x4 (NI) E00530-040WF Screw BH M3.0x6 (NI) E00530-060WF...
  • Page 179: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 3 Parts List & Location for Unit Mechanism Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 5-13 CL-E700 series...
  • Page 180 Chapter 5 Parts Lists DRAWING NO. 3 Unit Mechanism (Rev. 0) (DRAW NO. 4) (DRAW NO. 6) (DRAW NO. 5) 5-14 CL-E700 series...
  • Page 181 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Mechanism Sheet No. 1/1 Drawing No. 3 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit Shaft Head Holder JM42007-0 Unit Head (Ref. Drawing No. 4) Label Heat Caution...
  • Page 182: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 4 Parts List & Location for Unit Head Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 5-16 CL-E700 series...
  • Page 183 Chapter 5 Parts Lists DRAWING NO. 4 Unit Head (Rev. 0) 5-17 CL-E700 series...
  • Page 184 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Head Sheet No. 1/2 Drawing No. 4 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit Bushing Head JM11201-0 Plate Head Earth JM14105-0 Bracket Head JM14101-0 Guard Head Connector...
  • Page 185 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Head Sheet No. 2/2 Drawing No. 4 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 4-21 Guide Head Cable JM14212-1 Screw BH M3.0x3 (NI) E00530-030WF Screw BH M3.0x4 (NI) E00530-040WF Screw PH M3.0x8 (NI)
  • Page 186: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 5 Parts List & Location for Unit PF Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 5-20 CL-E700 series...
  • Page 187 Chapter 5 Parts Lists DRAWING NO. 5 Unit PF (Rev. 0) 5-21 CL-E700 series...
  • Page 188 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit PF Sheet No. 1/2 Drawing No. 5 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit SA PF Motor (with Thermistor) PPF80010-0 Plate Motor Bracket PAE00039-0 SA Main Frame L...
  • Page 189 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit PF Sheet No. 2/2 Drawing No. 5 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 5-21 Holder Guide Sensor L JM44207-0 Lever Head Lock JM44203-0 Spring Head Lock...
  • Page 190: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 6 Parts List & Location for Unit Sensor U Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 5-24 CL-E700 series...
  • Page 191 Chapter 5 Parts Lists DRAWING NO. 6 Unit Sensor U (Rev. 0) 5-25 CL-E700 series...
  • Page 192 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Sensor U Sheet No. 1/2 Drawing No. 6 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit SA Head Up Sensor PCB JM66715-1 SA Head Up Sensor Cable...
  • Page 193 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Sensor U Sheet No. 2/2 Drawing No. 6 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 6-21 Screw NO.0 TFH (PT4-0.5) M2.0x4 E15920-040WF Screw BH M3.0x6 (NI)
  • Page 194: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 7 Parts List & Location for Unit Opepane Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 5-28 CL-E700 series...
  • Page 195 Chapter 5 Parts Lists DRAWING NO. 7 Unit Opepane (Rev. 0) & " 5-29 CL-E700 series...
  • Page 196 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Opepane Sheet No. 1/1 Drawing No. 7 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit Sheet Ope-Pane PRN30010-0 Cover LCD PBA10002-0 Cover Ope-Pane PBA00095-0 Holder Ope-Pane Cover...
  • Page 197: Drawing No. 8

    Chapter 5 Parts Lists CL-E700 series Drawing No. 8 Parts List & Location for Unit Ribbon Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 Oct. 10, 2014 Oct. 10, 2014 5-31 CL-E700 series...
  • Page 198 Chapter 5 Parts Lists DRAWING NO. 8 Unit Ribbon (Rev. 0) 10 41 5-32 CL-E700 series...
  • Page 199 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Ribbon Sheet No. 1/3 Drawing No. 8 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit SA Ribbon Tension Unit R PPG30002-0 SA2 Ribbon Unit Fan (Ref. Drawing No. 9)
  • Page 200 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Ribbon Sheet No. 2/3 Drawing No. 8 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 8-21 SA Ribbon Encoder PPS90030-0 SA Ribbon Frame (with Support) PPC60035-0...
  • Page 201 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Unit Ribbon Sheet No. 3/3 Drawing No. 8 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 8-41 Screw No0 (BT4x0.5)M1.7x4 (NI) E13717-040WF E-Ring 4.0 E60340-000F Screw PHT(#2) M3.0x8 (NI) E10130-080WF E-Ring 3.0...
  • Page 202: Drawing No

    Chapter 5 Parts Lists CL-E700 series Drawing No. 9 Parts List & Location for SA2 Ribbon Unit Fan Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 5-36 CL-E700 series...
  • Page 203 Chapter 5 Parts Lists DRAWING NO. 9 SA2 Ribbon Unit Fan (Rev. 0) " 5-37 CL-E700 series...
  • Page 204 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: SA2 Ribbon Unit Fan Sheet No. 1/1 Drawing No. 9 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit Cover Ribbon Motor PBA00098-0 SA Fan JM68702-0 Plate Fan PAE00038-0 Screw BHT (#2) M3.0x6 (NI)
  • Page 205 Chapter 5 Parts Lists CL-E700 series Drawing No. 10 Parts List & Location for Accessories Revision Up List Sheet No. Rev. No. Date Oct. 10, 2014 5-39 CL-E700 series...
  • Page 206 Chapter 5 Parts Lists DRAWING NO. 10 Accessories (Rev. 0) 5-40 CL-E700 series...
  • Page 207 Chapter 5 Parts Lists PARTS LIST for CL-E700 series TITLE: Accessories Sheet No. 1/1 Drawing No. 10 Rev. No. 0 Q'ty/ Location Part Name Part No. Remarks Unit 10-1-1 Cord Set CS87-00004605 For CSA -1-2 Cord Set CS87-00004848 For CSE...
  • Page 208 Chapter 6. Circuit Diagrams HAPTER IRCUIT IAGRAMS CL-E700 series...
  • Page 209 SA Main PCB (12/12) [LAN I/F]....................6-14 SA Opepane PCB ........................6-15 SA Relay PCB ..........................6-16 SA Ref Sensor PCB .........................6-17 SA TRA Sen PCB ........................6-18 SA Head Up Sensor PCB......................6-19 SA Ribbon Control PCB ......................6-20 SA Ribbon Sensor........................6-21 SA Ribbon Encoder........................6-22 CL-E700 series...
  • Page 210: Inter Connection

    Chapter 6. Circuit Diagrams Inter Connection SA PF MOTOR (WITH THERMISTOR) PPF80010-** SA Head (200DPI)S PPM80015-** SA MAIN PCB (200ENG) PPS00152-** SA MAIN PCB (200CHN) PPS00218-** SA MAIN PCB (200ASIA) PPS00219-** CL-E700 series...
  • Page 211: Sa Main Pcb (1,2/12) [Cpu (1)]

    I / / / / / / / / / / Title / / / MAIN PCB / CPU (1) (1,2/12) / / / / / / Size Number Revision / / / PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 212: Sa Main Pcb (3/12) [Cpu (2)]

    03: GND 04: TCK 05: GND 06: TDO 07: NC 08: TDI 09: GND 10: nRES nRES ( " " ) ARM JTAG Title MAIN PCB / CPU (2) (3/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 213: Sa Main Pcb (4/12) [Rom, Sdram]

    Chapter 6. Circuit Diagrams SA Main PCB (4/12) [ROM, SDRAM] ( " " ) ( " " ) ( " " ) Title MAIN PCB / ROM, SDRAM (4/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 214: Sa Main Pcb (5/12) [Fpga]

    Chapter 6. Circuit Diagrams SA Main PCB (5/12) [FPGA] Rx/Cx -2 1 -2 1 Title MAIN PCB / FPGA (5/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 215: Sa Main Pcb (6/12) [Head, Opepane & Buzzer]

    / 1G / 2G ( " " ) g i l g i l 1 5V 3G 4 Title MAIN PCB / HEAD, OPEPANE, BUZZER (6/12) ( " " ) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 216: Sa Main Pcb (7/12) [Ribbon, Cutter & Peeler]

    Chapter 6. Circuit Diagrams SA Main PCB (7/12) [Ribbon, Cutter & Peeler] Rx/Cx ( " " ) & & Title MAIN PCB / RIBBON, CUTTER, PEELER (7/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: CL-E700 series...
  • Page 217: Sa Main Pcb (8/12) [Pf Motor Drive & Option I/F]

    Chapter 6. Circuit Diagrams SA Main PCB (8/12) [PF Motor Drive & Option I/F] ( " " ) t s i Title MAIN PCB / PF MOTOR DRIVER, OPTION I/F (8/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: 6-10 CL-E700 series...
  • Page 218: Sa Main Pcb (9/12) [Media Sensors & Head Up Sensor]

    SA Main PCB (9/12) [Media Sensors & Head Up Sensor] ( " " ) ( " " ) ( " " ) Title MAIN PCB / PAPER SENSOR, HEAD UP SENSOR (9/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: 6-11 CL-E700 series...
  • Page 219: Sa Main Pcb (10/12) [Usb I/F & Dac]

    L →H: 2.67[V](3.56[V]) (L/H: USB connected/disconnected) 100k 100k ( " " ) ( " " ) Title ( " " ) MAIN PCB / USB INF, DAC (10/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: 6-12 CL-E700 series...
  • Page 220: Sa Main Pcb (11/12) [Power Supply]

    Chapter 6. Circuit Diagrams SA Main PCB (11/12) [Power Supply] 100k Title MAIN PCB / POWER (11/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: 6-13 CL-E700 series...
  • Page 221: Sa Main Pcb (12/12) [Lan I/F]

    Chapter 6. Circuit Diagrams SA Main PCB (12/12) [LAN I/F] 5 7 5 7 Title MAIN PCB / LAN INF (12/12) Size Number Revision PPS00152/PPS00218/PPS00219-** Date: Sheet File: Drawn By: 6-14 CL-E700 series...
  • Page 222: Sa Opepane Pcb

    Chapter 6. Circuit Diagrams SA Opepane PCB g i l Title OPEPANE PCB Size Number Revision PPS00157-00 Date: Sheet File: Drawn By: 6-15 CL-E700 series...
  • Page 223: Sa Relay Pcb

    Chapter 6. Circuit Diagrams SA Relay PCB Title RELAY PCB Size Number Revision PPS00158-00 Date: Sheet File: Drawn By: 6-16 CL-E700 series...
  • Page 224: Sa Ref Sensor Pcb

    Chapter 6. Circuit Diagrams SA Ref Sensor PCB V3R3 CN501 D501 D502 TR501 GL100MN0MP GL100MN0MP PT100MC0MP CHP1505-0101 Title REFLECTIVE SENSOR PCB Size Number Revision JM66730-** Date: Sheet File: Drawn By: 6-17 CL-E700 series...
  • Page 225: Sa Tra Sen Pcb

    Chapter 6. Circuit Diagrams SA TRA Sen PCB V3R3 CN401 TR401 PT4800F6 03FMS-1.0SP-TF Title TRANSPARENT SENSOR PCB Size Number Revision JM66725-** Date: Sheet File: Drawn By: 6-18 CL-E700 series...
  • Page 226: Sa Head Up Sensor Pcb

    Chapter 6. Circuit Diagrams SA Head Up Sensor PCB CN201 C201 C202 PI201 1000p 1000p SG-278 S3B-PH-K-S Title HEAD UP SENSOR PCB Size Number Revision JM66715-** Date: Sheet File: Drawn By: 6-19 CL-E700 series...
  • Page 227: Sa Ribbon Control Pcb

    Chapter 6. Circuit Diagrams SA Ribbon Control PCB t s i Title RIBBON CONTROL PCB Size Number Revision PPS00161-00 Date: Sheet File: Drawn By: 6-20 CL-E700 series...
  • Page 228: Sa Ribbon Sensor

    Chapter 6. Circuit Diagrams SA Ribbon Sensor Title RIBBON SENSOR PCB Size Number Revision PPS00159-00 Date: Sheet File: Drawn By: 6-21 CL-E700 series...
  • Page 229: Sa Ribbon Encoder

    Chapter 6. Circuit Diagrams SA Ribbon Encoder Title RIBBON ENCODER PCB Size Number Revision PPS00160-00 Date: Sheet File: Drawn By: 6-22 CL-E700 series...
  • Page 230 Appendices PPENDICES AP-1 CL-E700 series...
  • Page 231 A-4. SA Ref Sensor PCB....................AP-5 A-5. SA TRA Sen PCB ....................AP-5 A-6. SA Head Up Sensor PCB ..................AP-6 A-7. SA Ribbon Control PCB................... AP-6 A-8. SA Ribbon Sensor ....................AP-6 A-9. SA Ribbon Encoder ....................AP-6 AP-2 CL-E700 series...
  • Page 232 Appendices A. Mounting Diagrams Mounting Diagrams A-1. SA Main PCB (1) Parts side AP-3 CL-E700 series...
  • Page 233 Appendices A. Mounting Diagrams (2) Solder side AP-4 CL-E700 series...
  • Page 234 Appendices A. Mounting Diagrams A-2. SA Opepane PCB (1) Parts side (2) Solder side A-3. SA Relay PCB A-4. SA Ref Sensor PCB D501 D502 CN501 A-5. SA TRA Sen PCB CN401 TR401 AP-5 CL-E700 series...
  • Page 235 Appendices A. Mounting Diagrams A-6. SA Head Up Sensor PCB (1) Parts side (2) Solder side C201 PI201 CN201 C202 A-7. SA Ribbon Control PCB A-8. SA Ribbon Sensor A-9. SA Ribbon Encoder AP-6 CL-E700 series...
  • Page 236 363 Van Ness Way, Suite 404 Torrance, CA 90501. USA Tel: (310) 781-1460 Fax:(310) 781-9152 http://www.citizen-systems.com Otto-Hirsch-Brücken 17 Park House, 643-651 Staines Road 70329 Stuttgart Feltham, Middlesex, TW14 8PA Germany United Kingdom Tel: +49 (0) 711 49032-0 Tel: +44 (0) 20 8893 1900...

Table of Contents