Related Manuals for IBASE Technology MB991AF
Summary of Contents for IBASE Technology MB991AF
- Page 1 MB991AF Core™ / ® ® Intel Xeon ® ® Pentium / Celeron Micro-ATX Motherboard User’s Manual Version 1.0 (July 2017)
- Page 2 No part of this publication may be reproduced, copied, stored in a retrieval system, translated into any language or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of IBASE Technology, Inc. (hereinafter referred to as “IBASE”). Disclaimer IBASE reserves the right to make changes and improvements to the products described in this document without prior notice.
-
Page 3: Compliance
0.1% by weight (1000 ppm) except for cadmium, limited to 0.01% by weight (100 ppm). • Lead (Pb) • Mercury (Hg) • Cadmium (Cd) • Hexavalent chromium (Cr6+) • Polybrominated biphenyls (PBB) • Polybrominated diphenyl ether (PBDE) MB991AF User’s Manual... -
Page 4: Important Safety Information
Danger of explosion if the internal lithium-ion battery is replaced by an incorrect type. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions or recycle them at a local recycling facility or battery collection point. MB991AF User’s Manual... -
Page 5: Warranty Policy
Software in use (such as OS and application software, including the version numbers) If repair service is required, you can download the RMA form at http://www.ibase.com.tw/english/Supports/RMAService/. Fill out the form and contact your distributor or sales representative. MB991AF User’s Manual... -
Page 6: Table Of Contents
2.1.1 Installing the Memory ............10 Setting the Jumpers ................11 2.2.1 How to Set Jumpers ............. 11 Jumper & Connector Locations on MB991AF ........12 Jumpers Quick Reference ..............13 2.4.1 CMOS Data Clearance (JP3) ..........13 2.4.2 RTC Data Clearance (JP4) ..........14 2.4.3... - Page 7 Fintek Super IO Hardware Monitor........59 4.4.10 CSM Configuration ...............60 4.4.11 NVMe Configuration .............61 4.4.12 USB Configuration ..............62 Chipset Settings ................64 4.5.1 System Agent (SA) Configuration .........65 4.5.2 PCH-IO Configuration ............68 Security Settings ................70 Boot Settings ..................71 Save & Exit Settings ................72 MB991AF User’s Manual...
- Page 8 Appendix ..................73 I/O Port Address Map ................ 74 Interrupt Request Lines (IRQ) ............77 Watchdog Timer Configuration ............79 On-Board Connector Types ............... 83 MB991AF User’s Manual viii...
-
Page 9: Chapter 1 General Information
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Specifications • Block Diagram • Board Overview • Board Dimensions... -
Page 10: Introduction
Introduction ® ® MB991AF is a Micro ATX motherboard based on the platform of Intel Xeon Gen. Core™ / Pentium ® ® / Celeron QC or DC processor. It offers high-definition visual experience and high performance on graphics processing. It can also be well utilized for designs of low power consumption in a board range of markets, including industrial control &... -
Page 11: Packing List
General Information Packing List Your MB991AF package should include the items listed below. If any of the items below is missing, contact the distributor or dealer from whom you purchased the product. • MB991AF Motherboard • I/O Shield • SATA Cable (SATA-3F) •... -
Page 12: Specifications
Yes (256 segments, 0, 1, 2…255 sec / min) Timer BIOS AMI BIOS ® iAMT 11.6 (supported by identified Intel DT CPU SKUs) iSMART 3.2 & EuP / ErP (Reserved) RAID RAID 0/1/5/10 244 x 244 mm (9.6” x 9.6”) Dimensions MB991AF User’s Manual... - Page 13 Operation: 0 ~ 60 °C (32 ~ 140 °F) • Temperature Storage: -20 ~ 80 °C (-4 ~ 176 °F) • Relative 0 ~ 90 %, non-condensing at 60 °C Humidity All specifications are subject to change without prior notice. MB991AF User’s Manual...
-
Page 14: Block Diagram
Block Diagram MB991AF User’s Manual... -
Page 15: Overview
＊The photos above are for reference only. Some minor components may differ. I/O View Name Name COM1 & COM2 Ports Audio Line-In (from top to bottom) COM3 & COM4 Ports Audio Line-Out (from top to bottom) USB 3.0 Ports Microphone-In LAN Ports HDMI Port MB991AF User’s Manual... -
Page 16: Dimensions
Dimensions 243.84 237.49 165.1 33.02 10.16 35.52 31.05 29.85 28.38 MB991AF User’s Manual... -
Page 17: Chapter 2 Hardware Configuration
Hardware Configuration This section provides information on jumper settings and connectors on the MB991AF in order to set up a workable system. On top of that, you will also need to install crucial pieces such as the CPU and the memory before using the product. The topics covered are: •... -
Page 18: Essential Installations Before You Begin
Follow the instructions below to install the memory. 2.1.1 Installing the Memory The MB991AF board supports four DDR4 memory sockets for a maximum total memory of 64 GB. To install the modules, locate the memory slot on the board and perform the following steps: Press the ejector tab of the memory slot down and outwards with your fingertips. -
Page 19: Setting The Jumpers
Hardware Configuration Setting the Jumpers Set up and configure your MB991AF by using jumpers for various settings and features according to your needs and applications. Contact your supplier if you have doubts about the best configuration for your use. 2.2.1... -
Page 20: Jumper & Connector Locations On Mb991Af
Jumper & Connector Locations on MB991AF CN1 & CPU_FAN1 ATX_12V_2X1 ® Intel Gen. Core™ / ® Pentium ® Celeron QC or DC REMOVE ® Intel C236 / Battery Q170 CN10 CN11 SYS_FAN1 SYS_FAN2 CN12 CN13 Board diagram of MB991AF MB991AF User’s Manual... -
Page 21: Jumpers Quick Reference
Jumpers Quick Reference Function Jumper Name Page CMOS Data Clearance RTC Data Clearance LVDS Power Selection LVDS Backlight Power Selection PCIe (x16) Bifurcation Factory Use Only 2.4.1 CMOS Data Clearance (JP3) Function Pin closed Illustration Normal (default) Clear CMOS MB991AF User’s Manual... -
Page 22: Rtc Data Clearance (Jp4)
2.4.2 RTC Data Clearance (JP4) Function Pin closed Illustration Normal (default) Clear RTC MB991AF User’s Manual... -
Page 23: Lvds Power Selection (Jp5)
Hardware Configuration 2.4.3 LVDS Power Selection (JP5) Function Pin closed Illustration 3.3V (default) MB991AF User’s Manual... -
Page 24: Lvds Backlight Power Selection (Jp6)
2.4.4 LVDS Backlight Power Selection (JP6) Function Pin closed Illustration 3.3V Open (default) Close MB991AF User’s Manual... -
Page 25: Pcie (X16) Bifurcation (Jp8)
Hardware Configuration 2.4.5 PCIe (x16) Bifurcation (JP8) Function Pin closed Illustration Open (default) x4, x4 Close MB991AF User’s Manual... -
Page 26: Connectors Quick Reference
CN7, CN8 CN9, CN10, CN11, SATA III Ports CN12, CN13 S3 Status Connector (reserved) DDR4 UDIMM Slot J10, J11, J12, J13 M.2 (M-key) Slot (PCIe only) mPCIe / mSATA Slot Factory Use Only J5, J18, J19, J23 MB991AF User’s Manual... -
Page 27: Com1 & Com2 Rs-232/422/485 Ports (Cn3)
DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground Assignment RS-232 RS-422 RS-485 DATA- DATA+ Ground Ground Ground MB991AF User’s Manual... -
Page 28: Com3 & Com4 Ports (Cn2)
COM3 & COM4 Ports (CN2) Assigment Assigment DCD, Data carrier detect DSR, Data set ready RXD, Receive data RTS, Request to send TXD, Transmit data CTS, Clear to send DTR, Data terminal ready RI, Ring indicator Ground MB991AF User’s Manual... -
Page 29: Digital I/O Connector (J3)
Hardware Configuration 2.5.3 Digital I/O Connector (J3) (4-In, 4-Out) Assigment Assigment Ground Out3 Out1 Out2 Out0 MB991AF User’s Manual... -
Page 30: Com7 ~ Com10 Ports (J7, J8)
2.5.4 COM7 ~ COM10 Ports (J7, J8) J7: (for COM7 & COM8) J8: (for COM9 & COM10) Assigment Assigment DCD#_A DSR#_A SIN#_A RTS#_A SOUT_A CTS#_A DTR#_A RI#_A DCD#_B DSR#_B SIN#_B RTS#_B SOUT_B CTS#_B DTR#_B RI#_B MB991AF User’s Manual... -
Page 31: Lvds Connector (J9, J15)
Hardware Configuration 2.5.5 LVDS Connector (J9, J15) J9: 2 channel J15: 1 channel Assigment Assigment LVSA_P LVSA_N LVSB_P LVSB_N LVSC_P LVSC_N LVSCK_P LVSCK_N LVSD_P LVSD_N 3.3V 3.3V MB991AF User’s Manual... -
Page 32: Usb 2.0 Ports (J14, J16)
2.5.6 USB 2.0 Ports (J14, J16) Assigment Assigment Ground Ground MB991AF User’s Manual... -
Page 33: Lvds Backlight Connector (J17)
Hardware Configuration 2.5.7 LVDS Backlight Connector (J17) Assigment Assigment +12V Brightness Control Backlight Enable Ground MB991AF User’s Manual... -
Page 34: Front Panel Setting Connector (J21)
Orientation is not required when making a connection to this header. • Power LED: Pins 7 and 8 This connector connects to the system power LED on control panel. This LED will light when the system turns on. MB991AF User’s Manual... -
Page 35: Atx Power Connector (J24)
Hardware Configuration 2.5.9 ATX Power Connector (J24) Assigment Assigment 3.3V 3.3V 3.3V -12V Ground Ground PS-ON Ground Ground Ground Ground Ground Power good 5VSB +12V +12V 3.3V Ground MB991AF User’s Manual... -
Page 36: At 12V Power Connector (Atx_12V_2X1)
2.5.10 AT 12V Power Connector (ATX_12V_2X1) Assigment Assigment Ground +12V Ground +12V Ground +12V Ground +12V MB991AF User’s Manual... -
Page 37: Cpu Fan Power Connector (Cpu_Fan1)
Hardware Configuration 2.5.11 CPU Fan Power Connector (CPU_FAN1) (PWM only) Assigment Assigment Ground Rotation detection +12V Control 2.5.12 System Fan Power Connector (SYS_FAN1, SYS_FAN2) SYS_FAN2 (PWM / DC mode) SYS_FAN1 Assigment Assigment Ground Rotation detection +12V Control MB991AF User’s Manual... - Page 38 This page is intentionally left blank. MB991AF User’s Manual...
-
Page 39: Chapter 3 Drivers Installation
Chapter 3 Drivers Installation This chapter introduces installation of the following drivers: • ® Intel Chipset Software Installation Utility • HD Graphics Driver • HD Audio Driver • LAN Driver • ® Intel Management Engine Drivers Installation • Fintek 8150s Serial Port Drivers... -
Page 40: Introduction
INF files for Plug & Play function for Intel chipset components. Follow the instructions below to complete the installation. Insert the disk enclosed in the package with the board. Click Intel on the left pane and then Intel(R) Skylake/Kabylake Chipset Drivers on the right pane. MB991AF User’s Manual... - Page 41 Accept the software license agreement and proceed with the installation process. On the Readme File Information screen, click Install for installation. The driver has been completely installed. You are suggested to restart the computer for changes to take effect. MB991AF User’s Manual...
-
Page 42: Hd Graphics Driver Installation
HD Graphics Driver Installation Click Intel on the left pane and then Intel(R) Skylake/Kabylake Chipset Drivers on the right pane. Click Intel(R) HD Graphics Driver. MB991AF User’s Manual... - Page 43 Accept the license agreement and click Next. On the Readme File Information screen, click Next until the installation starts. The driver has been completely installed. You are suggested to restart the computer for changes to take effect. MB991AF User’s Manual...
-
Page 44: Hd Audio Driver Installation
Click Realtek High Definition Audio Driver. On the Welcome screen of the InstallShield Wizard, click Next. Click Next until the installation starts. The driver has been completely installed. You are suggested to restart the computer for changes to take effect. MB991AF User’s Manual... -
Page 45: Lan Driver Installation
Driver Installation LAN Driver Installation Click Intel on the left pane and then Intel(R) Skylake/Kabylake Chipset Drivers on the right pane. Click Intel(R) PRO LAN Network Drivers.. MB991AF User’s Manual... - Page 46 On the Setup Options screen, click the checkbox to select the desired driver(s) for installation. Then click Next to continue. The wizard is ready for installation. Click Install. As the installation is complete, you are suggested to restart the computer for changes to take effect. MB991AF User’s Manual...
-
Page 47: Intel ® Management Engine Drivers Installation
Driver Installation ® Intel Management Engine Drivers Installation Click Intel on the left pane and then Intel(R) Skylake/Kabylake Chipset Drivers on the right pane. Click Intel(R) ME 11.x Drivers. MB991AF User’s Manual... - Page 48 When the Welcome screen appears, click Next. Accept the license agreement and click Next until the installation starts. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect. MB991AF User’s Manual...
-
Page 49: Fintek 8150X Serial Port Drivers Installation
Driver Installation Fintek 8150x Serial Port Drivers Installation Click Intel on the left pane and then Intel(R) Skylake/Kabylake Chipset Drivers on the right pane. Click Fintek 8150x Serial Port Drivers. MB991AF User’s Manual... - Page 50 When the Welcome screen appears, click Next. Accept the license agreement and click Install until the installation starts. As the driver has been sccessfully installed, you are suggested to restart the computer for changes to take effect. MB991AF User’s Manual...
-
Page 51: Chapter 4 Bios Setup
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Boot Settings •... -
Page 52: Introduction
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. MB991AF User’s Manual... -
Page 53: 4.3 Main Settings
BIOS Setup 4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. MB991AF User’s Manual... -
Page 54: 4.4 Advanced Settings
Displays super IO chip parameters. Configuration Fintek Super IO Shows super IO monitor hardware status. Hardware Monitor CSM Configuration Enables / Disables option ROM execution settings, etc. NVMe Configuration NVMe device option settings. USB Configuration Displays USB configuration parameters. MB991AF User’s Manual... -
Page 55: Cpu Configuration
Disabled for other OS (OS not optimized for Hyper-Threading Technology). Enables / Disables AES (Advanced Encription Standard). Intel Trusted Enables / Disables utilization of additional Execution Technology hardware capabilities provided by Intel(R) Trusted Execution Technology. Changes require a full power cycle to take effect. MB991AF User’s Manual... -
Page 56: Power & Performance
Technology support. Enabling will expose the CPPC v2 interface to allow for hardware controlled P-states. Turbo Mode Enables / Disables processor Turbo Mode (requires EMMTTM enabled too). Auto means enabled, unless max. turbo ration is bigger than 16-SKL AO W/A. MB991AF User’s Manual... -
Page 57: Pch-Fw Configuration
PCH-FW Configuration BIOS Setting Description AMT BIOS Features When disabled AMT BIOS features are no longer supported and user is no longer able to access MEBx Setup. Note: This option does not disable Manageability features in FM. MB991AF User’s Manual... -
Page 58: Trusted Computing
TCG_2: supports new TCG2 protocol and event format for Windows 10 or later. Physical Presence Select to tell OS to support PPI spec version 1.2 Spec Version or 1.3. Note: some HCK tests might not support 1.3. MB991AF User’s Manual... -
Page 59: Acpi Settings
(OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state where the system will enter when the Suspend button is pressed. Options: Suspend Disabled, S3 (Suspend to RAM) MB991AF User’s Manual... -
Page 60: Lvds (Edp/Dp) Configuration
4.4.6 LVDS (eDP/DP) Configuration BIOS Setting Description LVDS (eDP/DP) Enables / Disables LVDS (eDP/DP). Support MB991AF User’s Manual... -
Page 61: Ismart Controller
Generate the reset signal when system hands up Guardian on POST. Schedule Slots Sets up the hour / minute / day for the power-on schedule for the system. Options: • None • Power On • Power On / Off MB991AF User’s Manual... -
Page 62: Fintek Super Io Configuration
Disable the function to shutdown the standby power. Options: All Enable, Enable Ethernet for WOL, All Disable. Serial Port Sets parameters of Serial Ports. Configuration Enables / Disables the serial port and select an optimal setting for the Super IO device. MB991AF User’s Manual... - Page 63 Serial Port 1 Mode Changes the serial port mode to RS-232 / 422 / Select 485. Options: • RS232 • RS485 TX Low Active • RS485 with Termination TX Low Active • RS422 • RS422 with Termination MB991AF User’s Manual...
- Page 64 Serial Port 1 Mode Changes the serial port mode to RS-232 / 422 / Select 485. Options: • RS232 • RS485 TX Low Active • RS485 with Termination TX Low Active • RS422 • RS422 with Termination MB991AF User’s Manual...
- Page 65 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 MB991AF User’s Manual...
- Page 66 IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2F0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 • IO = 2E0h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 MB991AF User’s Manual...
-
Page 67: Fintek Super Io Hardware Monitor
The values are read-only values as monitored by the system and show the PC health status. CPU Shutdown Options: Disabled / 70 °C / 75 °C / 80 °C / 85 °C / Temperature 90 °C / 95 °C MB991AF User’s Manual... -
Page 68: Csm Configuration
Boot option filter Controls the priority of Legacy and UEFI ROMs. Options: UEFI and Legacy / Legacy only / UEFI only Network Controls the execution of UEFI and Legacy PXE OpROM. Options: Do not launch / Legacy MB991AF User’s Manual... -
Page 69: Nvme Configuration
Controls the execution of UEFI and Legacy Video OpROM. Options: Do not lanuch / UEFI / Legacy Other PCI devices Determines OpROM execution policy for devices other than network, storage or video. Options: Do not lanuch / UEFI / Legacy 4.4.11 NVMe Configuration MB991AF User’s Manual... -
Page 70: Usb Configuration
Options: 1 sec / 5 sec / 10 sec / 20 sec Device reset time-out Seconds of delaying execution of start unit command to USB mass storage device. Options: 10 sec / 20 sec / 30 sec / 40 sec MB991AF User’s Manual... - Page 71 Optional drives are emulated as CDROM drives with no media will be emulated according to a drive type. Options: Auto / Floppy / Forced FDD / Hard Disk / CD-ROM MB991AF User’s Manual...
-
Page 72: 4.5 Chipset Settings
4.5 Chipset Settings BIOS Setting Description System Agent (SA) System Agent (SA) parameters Configuration PCH-IO Configuration PCH parameters MB991AF User’s Manual... -
Page 73: System Agent (Sa) Configuration
BIOS Setup 4.5.1 System Agent (SA) Configuration BIOS Setting Description Memory Configuration Displays the memory configuration parameters. Graphics Configures the graphics settings. Configuration VT-d Checks if VT-d function on MCH is supported. MB991AF User’s Manual... - Page 74 External Gfx Card Configures the external Gfx card primary display. Primary Display • Primary PEG: Selects the primary PEG Configuration (options: Auto / PEG11 / PEG12). • Primary PCIE: Selects the primary PCIe (options: Auto / PCIE1 ~ PCIE18) MB991AF User’s Manual...
- Page 75 20M / 24M / 28M / 32M/F7 / 36M / 40M / 44M / 48M / 52M / 56M / 60M DVMT Total Gfx Mem Selects DVMT 5.0 total graphic memory size used by the internal graphcis device. Options: 256M / 128M / MAX MB991AF User’s Manual...
-
Page 76: Pch-Io Configuration
PCH LAN Controller Enables / Disables the onboard NIC. Wake on LAN Enable Enables / Disables the integrated LAN to wake up the system. SLP_LAN# Low on Enables / Disables the SLP_LAN# Low on DC DC Power Power MB991AF User’s Manual... - Page 77 Enables / Disables the SATA device. SATA Mode Selection Determines how SATA controller(s) operate. Options: AHCI / Intel RST Premium Serial ATA Port 0~2 Enables / Disables Serial Port 0 ~ 2. SATA Ports Hot Plug Enables / Disables SATA Ports HotPlug. MB991AF User’s Manual...
-
Page 78: 4.6 Security Settings
4.6 Security Settings BIOS Setting Description Administrator Sets an administrator password for the setup Password utility. User Password Sets a user password. MB991AF User’s Manual... -
Page 79: 4.7 Boot Settings
Has no effect for BBS boot options. New Boot Option Controls the placement of newly detected UEFI Policy boot option. FIXED BOOT ORDER Sets the system boot order. Priorities MB991AF User’s Manual... -
Page 80: 4.8 Save & Exit Settings
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Defaults Saves the changes done so far as User Defaults. Restore User Defaults Restores the user defaults to all the setup options. MB991AF User’s Manual... -
Page 81: Appendix
Appendix This section provides the mapping addresses of peripheral devices, the sample code of watchdog timer configuration, and types of on-board connectors. -
Page 82: I/O Port Address Map
0x000000B2-0x000000B3 Motherboard resources 0x00000680-0x0000069F Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources 0x00001800-0x000018FE Motherboard resources 0x0000164E-0x0000164F Motherboard resources 0x00000020-0x00000021 Programmable interrupt controller 0x00000024-0x00000025 Programmable interrupt controller 0x00000028-0x00000029 Programmable interrupt controller 0x0000002C-0x0000002D Programmable interrupt controller MB991AF User’s Manual... - Page 83 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x000003E8-0x000003EF Communications Port (COM3) 0x000002E8-0x000002EF Communications Port (COM4) 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer 0x00001854-0x00001857 Motherboard resources 0x00000000-0x00000CF7 PCI Express Root Complex MB991AF User’s Manual...
- Page 84 Intel(R) 100 Series / C230 Series Chipset Family PCI Express Root Port #7 - A116 0x0000D000-0x0000DFFF FINTEK PCIe To Serial 0x0000D080-0x0000D08F FINTEK PCIe To Serial 0x0000D060-0x0000D07F FINTEK PCIe To Serial 0x0000D040-0x0000D05F FINTEK PCIe To Serial 0x0000D020-0x0000D03F FINTEK PCIe To Serial MB991AF User’s Manual...
-
Page 85: Interrupt Request Lines (Irq)
High Definition Audio Controller IRQ 18 Communications Port (COM7) IRQ 18 Communications Port (COM8) IRQ 18 Communications Port (COM9) IRQ 18 FINTEK Pcie To Serial IRQ 18 Communications Port (COM6) IRQ 19 Intel(R) Active Management Technology - SOL (COM5) MB991AF User’s Manual... - Page 86 Standard SATA AHCI Controller IRQ 4294967293 Intel(R) 100 Series / C230 Series Chipset Family PCI Express Root Port #7 - A116 IRQ 4294967294 Intel(R) 100 Series / C230 Series Chipset Family PCI Express Root Port #6 - A115 MB991AF User’s Manual...
-
Page 87: Watchdog Timer Configuration
**endptr; char SIO; printf("Fintek 81866 watch dog program\n"); SIO = Init_F81866(); if (SIO == 0) printf("Can not detect Fintek 81866, program abort.\n"); return(1); }//if (SIO == 0) if (argc != 2) printf(" Parameter incorrect!!\n"); return (1); MB991AF User’s Manual... - Page 88 DisableWDT(void) unsigned char bBuf; Set_F81866_LD(0x07); //switch to logic device 7 bBuf = Get_F81866_Reg(0xFA); bBuf &= ~0x01; Set_F81866_Reg(0xFA, bBuf); //disable WDTO output bBuf = Get_F81866_Reg(0xF5); bBuf &= ~0x20; bBuf |= 0x40; Set_F81866_Reg(0xF5, bBuf); //disable WDT //--------------------------------------------------------------------------- //--------------------------------------------------------------------------- MB991AF User’s Manual...
- Page 89 Init_Finish; F81866_BASE = 0x00; result = F81866_BASE; Init_Finish: return (result); //--------------------------------------------------------------------------- void Unlock_F81866 (void) outportb(F81866_INDEX_PORT, F81866_UNLOCK); outportb(F81866_INDEX_PORT, F81866_UNLOCK); //--------------------------------------------------------------------------- void Lock_F81866 (void) outportb(F81866_INDEX_PORT, F81866_LOCK); //--------------------------------------------------------------------------- void Set_F81866_LD( unsigned char LD) Unlock_F81866(); outportb(F81866_INDEX_PORT, F81866_REG_LD); outportb(F81866_DATA_PORT, LD); Lock_F81866(); MB991AF User’s Manual...
- Page 90 #define F81866_DATA_PORT (F81866_BASE+1) //--------------------------------------------------------------------------- #define F81866_REG_LD 0x07 //--------------------------------------------------------------------------- #define F81866_UNLOCK 0x87 #define F81866_LOCK 0xAA //--------------------------------------------------------------------------- unsigned int Init_F81866(void); void Set_F81866_LD( unsigned char); void Set_F81866_Reg( unsigned char, unsigned char); unsigned char Get_F81866_Reg( unsigned char); //--------------------------------------------------------------------------- #endif // F81866_H MB991AF User’s Manual...
-
Page 91: On-Board Connector Types
Appendix On-Board Connector Types Connector Function Type Name COM5 & COM6 RS-485 Port J1, J2 E-CALL_0110-2610030 Only available for MB991AF-D DVI-D Port HK_DF11-20S-PA66H Only available for MB991AF-D LVDS Connector J9, J15 HIROSE_DF20G-20DP-1V(56) COM7 ~ COM10 Ports J7, J8 HK_DF11-20S-PA66H USB 2.0 Ports...