Related Manuals for IBASE Technology MB900-R
Summary of Contents for IBASE Technology MB900-R
- Page 1 MB900-R Socket LGA775 Pentium ® Intel 945G Chipset ® Industrial Motherboard USER’S MANUAL Version 1.0...
- Page 2 Award is a registered trademark of Award Software International, Inc. PS/2 is a trademark of International Business Machines Corporation. Intel and Pentium 4 are registered trademarks of Intel Corporation. Microsoft Windows is a registered trademark of Microsoft Corporation. Winbond is a registered trademark of Winbond Electronics Corporation.
-
Page 3: Table Of Contents
Watchdog Timer Configuration ...20 BIOS Setup ... 25 Drivers Installation Intel 945G Chipset Software Installation Utility ...48 Intel 945G Chipset Graphics Driver ...50 Realtek Codec Audio Driver Installation ...51 Marvell 88E8052 LAN Drivers Installation ...52 Intel PRO LAN Drivers Installation...53 Appendix ... - Page 4 This page is intentionally left blank. MB900-R User’s Manual...
-
Page 5: Introduction
Introduction Checklist Your MB900-R Pentium items listed below: The MB900-R motherboard This User’s manual 1 Back I/O shield 1 IDE cable 1 Floppy cable 1 SATA cable 1 Serial-Port cable 1 CD containing the following: Chipset Drivers Flash Memory Utility MB900-R User’s Manual... -
Page 6: Mb900-R Specifications
MB900-R Specifications Form Factor Micro-ATX / 244mm x 244mm CPU Type Intel Pentium D (dual core) / Pentium 4 / Celeron D CPU Voltage 0.8375V~1.6V (VRD 10.1) System Speed 3.8GHz CPU FSB 533/800/1066MHz Green /APM APM1.2 CPU Socket Socket 775... -
Page 7: Board Dimensions
INTRODUCTION Board Dimensions MB900-R User’s Manual... -
Page 8: Installations
Installations This section provides information o n how to use the jumpers and connectors on the MB900-R in order to set up a workable system. The topics covered are: Installing the CPU ... 5 ATX Power Installation ... 6 Installing the Memory ... 6 Setting the Jumpers ... -
Page 9: Installing The Cpu
INSTALLATIONS Installing the CPU The MB900-R motherboard supports an LGA 775 processor socket for Intel® Pentium® 4 processors. The LGA 775 processor socket comes with a lever to secure the processor. Refer to the pictures below, from left to right, on how to place the processor into the CPU socket. -
Page 10: Atx Power Installation
ATX power connector in a standard ATX power supply (Min. 400watt). Note: The power supply 5VSB voltage must be at least 2A . Installing the Memory The MB900-R motherboard supports two DDR2 memory sockets for a maximum total memory of 2GB in DDR memory type. It supports DDR2 533/667. -
Page 11: Setting The Jumpers
Setting the Jumpers Jumpers are used on MB900-R to select various settings and features according to your needs and applications. Contact your su pplier if you have doubts about the best configuration for your needs. The following lists the connectors on MB900-R and their respective functions. - Page 12 INSTALLATIONS Jumper Locations on MB900 -R JP1, JP2, JP3: RS232/422/485 (COM2) Selection ... 9 JP4: IDE DMA Mode Setting ... 9 JP6: Clear CMOS Contents ... 9 JP7: CF Socket Master / Slave Selection ... 10 MB900-R User’s Manual...
- Page 13 JP4: IDE DMA Mode Setting JP6: Clear CMOS Contents Use JP6, a 3-pin header, to clear the CMOS contents. Note that the ATX-power connector should be disconnected from the motherboard before clearing CMOS. MB900-R User’s Manual RS-232 RS-422 JP1: JP1:...
- Page 14 INSTALLATIONS JP7: CF Socket Master / Slave Selection CF Mode Slave Master MB900-R User’s Manual...
-
Page 15: Connectors On Mb900-R
INSTALLATIONS Connectors on MB900-R The connectors on MB900-R allows you to connect external devices such as keyboard, floppy disk drives, hard disk drives, printers, etc. The following table lists the connectors o n MB900-R and their respective functions. ATX1: 24-pin ATX Power Connector ...13 ATX2: ATX 12V Power Connector ...13... - Page 16 Connector Locations on MB900-R ATX1: 24-pin ATX Power Connector... 13 ATX2: ATX 12V Power Connector ... 13 MB900-R Edge Connectors ... 13 CN1: PS/2 Keyboard and PS/2 Mouse Connectors ... 14 CN2, J2, J7, J8: COM1/2/3/4 Serial Ports ... 14 CN3: Parallel Port Connector ...
-
Page 17: Atx1: 24-Pin Atx Power Connector
-12V Ground PS-ON Ground Ground Ground Ground ATX2: ATX 12V Power Connector Signal Name +12V +12V +12V +12V MB900-R Edge Connectors MB900-R User’s Manual Pin # Pin # Signal Name 3.3V 3.3V Ground Ground Ground Power good 5VSB +12V +12V +3.3V... -
Page 18: Cn1: Ps/2 Keyboard And Ps/2 Mouse Connectors
DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND, ground COM2 is jumper selectable for RS -232, RS-422 and RS-485. Pin # RS-232 MB900-R User’s Manual Keyboard Pin # Signal Keyboard data N.C. N.C. COM2... -
Page 19: Cn3: Parallel Port Connector
Select CN4: VGA CRT Connector CN4 is a DB-15 VGA connector located beside the COM1 port. The following table shows the pin-out assignments of this connector. Signal Name MB900-R User’s Manual CN4 Parallel Port Pin # Pin # Signal Name... -
Page 20: Cn5: Audio Connector
CN5: Audio Connector CN6: 10/100 RJ-45 and USB0/1 Connector CN7: GbE RJ-45 and USB2/3 Connector CN11, CN10: SATA0/1 Connector MB900-R User’s Manual Pin # Signal Name Ground Ground Ground... -
Page 21: J1: Digital I/O Connector (4 In, 4 Out)
J3: Audio Front Header Signal Name MIC2_L MIC2_R Line2_L Sense Line2_R J5: USB4/USB5 Connector Signal Name J6: USB6/USB7 Connector Signal Name MB900-R User’s Manual Pin # Pin # Pin # Pin # Ground Protect Pin Ground Protect Pin Signal Name Out1... -
Page 22: J9: Wake On Lan Connector
Signal Name HD_LED+ HD_LED- RST_SW- RST_SW+ Reserved J11: IrDA Connector FAN1: CPU Fan Power Connector MB900-R User’s Manual Signal Name +5VSB Ground LAN Wakeup Pin # Pin # PWR/ SLP_LED+ PWR/ SLP_LED- Pin #... -
Page 23: Fan2, Fan3, Fan4: Fan Power Connectors
PCIE_1: x16 PCI Express Slot PCIE_2: x1 PCI Express Slot PCI1, PCI5: PCI Slots CN12: CF Socket J12: SMBus This is a 2-pin header. Pin 1 is SMB_CLK; Pin 2 is SMB_DATA. MB900-R User’s Manual Pin # Signal Name Ground +12V Rotation detection... -
Page 24: Watchdog Timer Configuration
Parameter incorrect!!\n"); return 1; if (Init_W627EHF() == 0) printf(" Winbond 83627HF is not detected, program abort. \n"); return 1; bTime = strtol (argv[1], endptr, 10); printf("System will reset after %d seconds \n", bTime); EnableWDT(bTime); return 0; //============================================= ============================== MB900-R User’s Manual... - Page 25 Set_W627EHF_Reg( 0xF5, bBuf); Set_W627EHF_Reg( 0xF6, interval); //=========================================================================== void DisableWDT(void) Set_W627EHF_LD(0x08); Set_W627EHF_Reg(0xF6, 0x00); Set_W627EHF_Reg(0x30, 0x00); //=========================================================================== MB900-R User’s Manual //Enable WDTO //switch to logic device 8 //enable timer //count mode is second //set timer //switch to logic device 8 //clear watchdog timer...
- Page 26 Unlock_W627EHF (void) outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); outportb(W627EHF_INDEX_PORT, W627EHF_UNLOCK); //=========================================================================== void Lock_W627EHF (void) outportb(W627EHF_INDEX_PORT, W627EHF_LOCK); //=========================================================================== void Set_W627EHF_LD( unsigned char LD) Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, W627EHF_REG_LD); outportb(W627EHF_DATA_PORT, LD); Lock_W627EHF(); //=========================================================================== void Set_W627EHF_Reg( unsigned char REG, unsigned char DATA) Unlock_W627EHF(); outportb(W627EHF_INDEX_PORT, REG); MB900-R User’s Manual...
- Page 27 // KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR // PURPOSE. //===================================================================== #include <dos.h> #include <conio.h> #include <stdio.h> #include <stdlib.h> MB900-R User’s Manual (W627EHF_BASE) (W627EHF_BASE+1) 0x07 0x87 0xAA...
- Page 28 I/O Input Changed. Current Data is 0x%X \n",ucDI); if (kbhit()) getch(); break; delay(500); return 0; //============================ ========================================= void ClrKbBuf(void) while(kbhit()) getch(); //--------------------------------------------------------------------------- MB900-R User’s Manual //data for digital output //data for digital input //switch to logic device 7 //clear...
-
Page 29: Bios Setup
Integrated Peripherals ...36 Power Management Setup ...40 PNP/PCI Configurations ... 43 PC Health Status...44 Frequency/Voltage Control ...45 Load Fail-Safe Defaults...46 Load Optimized Defaults ... 46 Set Supervisor/User Password...46 Save & Exit Setup ...46 Exit Without Saving ...46 MB900-R User’s Manual... -
Page 30: Bios Introduction
BIOS Introduction The Award BIOS (Basic Input/Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine -tuning of the chipset controlling the entire system. - Page 31 Award and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could cause the system to become unstable and crash in some cases. MB900-R User’s Manual Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults...
-
Page 32: Standard Cmos Setup
Day : Sun to Sat Month : 1 to 12 Date : 1 to 31 Year : 1999 to 2099 MB900-R User’s Manual Standard CMOS Features Wed, Apr 28, 2004 00 : 00 : 00 None None None None 1.44M, 3.5 in. - Page 33 These fields identify the types of floppy disk drive A or drive B that has been installed in the computer. The available specifications are: 360KB 1.2MB 5.25 in. 5.25 in. MB900-R User’s Manual Number of cylinders Number of read/write heads Write precompensation Landing zone Number of sectors (HD <...
- Page 34 No errors All errors All, But Keyboard All, But Diskette All, But Disk/Key MB900-R User’s Manual For EGA, VGA, SEGA, SVGA or PGA monitor adapters. (default) Power up in 40 column mode. Power up in 80 column mode. For Hercules or MDA adapters.
-
Page 35: Advanced Bios Features
DRAM into cache memory, for even faster access by the CPU. These items allow you to enable (speed up memory access) or disable the cache function. By default, these items are Enabled. MB900-R User’s Manual Advanced BIOS Features Press Enter... - Page 36 When enabled, you can set the two typematic controls listed next. By default, this field is set to Disabled. Typematic Rate (Chars/Sec) When the typematic rate is enabled, the system registers repeated keystrokes speeds. Settings are from 6 to 30 characters per second. MB900-R User’s Manual...
- Page 37 If you set this feature to Disabled, the BIOS will not report the missing floppy drive to Win95/98. Small Logo (EPA) Show The EPA logo appears at the right side of the monitor screen when the system is boot up. The default setting is Enabled. MB900-R User’s Manual...
-
Page 38: Advanced Chipset Features
This option allows you to insert a delay between the RAS (Row Address Strobe) and CAS (Column Address Strobe) signals. This delay occurs when the SDRAM is written to, read from or refreshed. Reducing the delay improves the performance of the SDRAM. MB900-R User’s Manual Advanced Chipset Features By SPD 533MHZ... - Page 39 PEG/On Chip VGA Control: Auto PEG Force x1: Disabled On-Chip Frame Buffer Size: 8MB DVMT Mode: DVMT DVMT/Fixed Memory Size: 128MB Onboard PCI-E LAN By default, this setting is enabled. Onchip ICH7 LAN By default, this setting is enabled. MB900-R User’s Manual...
-
Page 40: Integrated Peripherals
Azalia AC97 Audio Select Phoenix - AwardBIOS CMOS Setup Utility Onboard Serial Port 3 Serial Port 3 Use IRQ Onboard Serial Port 4 Serial Port 4 Use IRQ MB900-R User’s Manual Integrated Peripherals Press Enter Press Enter Menu Level > Press Enter... -
Page 41: Ide Hdd Block Mode
IDE Primary/Secondary Master/Slave UDMA These fields allow your system to improve disk I/O throughput to 33Mb/sec with the Ultra DMA/33 feature. The options are Auto and Disabled. MB900-R User’s Manual SuperIO Device BUTTON ONLY Enter Ctrl-F1 Enabled Menu Level >... - Page 42 If you install an add-in FDC or the system has no floppy drive, select Disabled in this field. This option allows you to select the onboard FDD port. MB900-R User’s Manual...
- Page 43 This field determines the UART 2 mode in your computer. The default value is Normal. Other options include IrDA and ASKIR. PWRON After PWR-Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation. MB900-R User’s Manual...
-
Page 44: Power Management Setup
This field allows you to select the type of power saving management modes. There are four selections for Power Management. Min. Power Saving Max. Power Saving User Define MB900-R User’s Manual Power Management Setup Enabled S1(POS) Auto Menu Level >... - Page 45 Resume by Alarm This field enables or disables the resumption of the system operation. When enabled, the user is allowed to set the Date and Time. MB900-R User’s Manual Default setting, blank the screen and turn off vertical and horizontal scanning.
- Page 46 When an I/O device wants to gain the attention of the operating system, it signals this by causing an IRQ to occur. When the operating system is ready to respond to the request, it interrupts itself and performs the service. MB900-R User’s Manual...
-
Page 47: Init Display First
MPEG ISA/VESA VGA card. When this field is disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card. Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 4096. MB900-R User’s Manual PnP/PCI Configurations PCI Slot Disabled... -
Page 48: Pc Health Status
Temperatures/Voltages These fields are the parameters of the hardware monitoring function feature of the motherboard. The values are read-only values as monitored by the system and show the PC health status. MB900-R User’s Manual PC Health Status Disabled Disabled 45°C/113°F Menu Level >... -
Page 49: Cpu Clock Ratio
This field enables or disables the auto detection of the PCI clock. Spread Spectrum Modulated This field sets the value of the spread spectrum. The default setting is Disabled. This field is for CE testing use only MB900-R User’s Manual Frequency/Voltage Control Disabled Menu Level >... -
Page 50: Load Fail-Safe Defaults
Select this option to exit the Setup utility without saving the changes you have made in this session. Typing “Y” will quit the Setup utility without saving the modifications. Typing “N” will return you to Setup utility. MB900-R User’s Manual... -
Page 51: Drivers Installation
Marvell 88E8052 LAN Drivers Installation... 52 Intel PRO LAN Drivers Installation...53 IMPORTANT NOTE: After installing your Windows operating system (Windows 2000/XP), you must install first the Intel Chipset Software Installation Utility before proceeding with the drivers installation. MB900-R User’s Manual... -
Page 52: Intel 945G Chipset Software Installation Utility
Intel 945G Chipset Software Installation Utility The Intel® 945G Chipset Drivers should be installed first before the software drivers to enable Plug & Play I NF support for Intel chipset components. Follow the instructions below to complete the installation under Windows 2000/XP. (Before installed Intel Chipset Software... - Page 53 3. Click Yes to accept the software license agreement and proceed with the installation process. 4. On Readme Information screen, click Next to continue the installation. 5. The Setup process is now complete. Click Finish to restart the computer and for changes to take effect. MB900-R User’s Manual...
-
Page 54: Intel 945G Chipset Graphics Driver
DRIVERS INSTALLATION Intel 945G Chipset Graphics Driver The Intel® 945G Chipset Family Graphics Drivers come in the CD with the motherboard. Follow the instructions below to complete the installation under Windows 2000/XP. 1. Insert the CD that comes with the board and the screen below would appear. -
Page 55: Realtek Codec Audio Driver Installation
Follow the steps below to install the Realtek High Definition Codec Audio Drivers. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel Chipsets, then Realtek High Definition Codec Audio Driver. 2. When the Welcome screen appears, click Next to continue. -
Page 56: Marvell 88E8052 Lan Drivers Installation
Properties). Click Advanced and select Wake From Shutdown. In the Value field on the right, select On. 3. Then, also in the Advanced section, click on Wake Up Capabilities. In the Value field on the right, select Magic Packet, then click OK. MB900-R User’s Manual... -
Page 57: Intel Pro Lan Drivers Installation
Windows 2000/XP. 1. Insert the CD that comes with the board and the screen below would appear. Click Intel Chipsets, then Intel (R) PRO LAN Network Drivers. 2. On the next screen, click Install Drivers to start the drivers installation. - Page 58 DRIVERS INSTALLATION This page is intentionally left blank. MB900-R User’s Manual...
-
Page 59: Appendix
378h - 3FFh 360h - 36Fh 3B0h - 3BFh 3C0h - 3CFh 3D0h - 3DFh 3F0h - 3F7h 3F8h - 3FFh MB900-R User’s Manual Device Description DMA Controller #1 Interrupt Controller #1 Timer Keyboard Controller Real Time Clock, NMI DMA Page Register... -
Page 60: Interrupt Request Lines (Irq)
IRQ4 IRQ5 IRQ6 IRQ7 IRQ8 IRQ9 IRQ10 IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 MB900-R User’s Manual Function System Timer Output Keyboard Interrupt Cascade Serial Port #2 Serial Port #1 Reserved Floppy Disk Controller Parallel Port #1 Real Time Clock Reserved Reserved...