• Strictly follow the instructions in this user manual. At first use, your DREAMPANEL TWIN may give off an odor. This is a Please take the time to read this manual carefully and thoroughly before normal occurrence that should dissipate after a few minutes of operation.
Do not shake the DREAMPANEL TWIN while installing or handling. To transport your DREAMPANEL TWIN, we strongly recommend that you Do not pull the DREAMPANEL TWIN by one of its cables to move it. Lift the use the complete original packaging, including the dense protective foam luminaire by its handles.
Page 6
(RDM)-type via ArtNet controller may be required. The RDM protocol is a universal, widely used standard. The DREAMPANEL TWIN consists of a metal frame and plastic covers. The power connectors, video and network signal connectors are on the back of the fixture’s base.
DESCRIPTION INSTALLATION INSTRUCTIONS During installation please observe the instructions according to GB7000.15 / EN60598-2-17 standards and other national standards applicable. This luminaire should be installed by a qualified technician. The fixture should be used in an environment with a temperature between -5°C and +45°C.
INSTALLATION METHOD USING TRUSS HOOKS THE DREAMPANEL TWIN DMX ADDRESS SETTING Refer to the following diagram when installing the DREAMPANEL TWIN All luminaires have a DMX start address correctly set when using a DMX with truss hooks using omega bracket: signal to control them.
Page 9
DREAMPANEL TWIN CONTROL PANEL MENU – The fixture’s menu functions are described in the following table: OPTION DETAILS Main address Set Dmx Addr A001~AXXX setting The following section provides details on the options that can be selected Set LED Addr...
EDIT USER A, B, C SERVICE PIN To customize the mode, go to “MODE” and select “Edit UserMode A, B or C” and press “Enter.” Scroll through each setting and press “Enter” to set WARNING! For normal operation the “Service pin” menu information the desired address.
Page 11
Key Lock Set To Slave Activates the automatic keypad lock. If this function is enabled, the keys Sets the fixture to SLAVE Mode for receiving instructions from a master will be automatically locked 15 seconds after exiting edit mode. Hold the luminaire (see Master/Save mode settings, below).
“Enter.” Then use the left/right arrow keys to access the “Network” from the control panel. Then run the scenes from your controller. They will submenu. be automatically transmitted to the DREAMPANEL TWIN. w Press “Enter” once again to display the information. TEST HOME Allows you to reset the functions from a DMX controller.
Page 13
Part 1: To launch a program, follow this procedure: 1. Slave Settings - SLAVE fixture adjustment Use the buttons to select “Function Mode.” Press ENTER to confirm. Part 2: Use the buttons to select “Set slave to.” Scene 10 Scene 11 Scene 12 Scene 13 Press ENTER to confirm.
DMX CHART DMX channel´s functions and their values (272 DMX channels) Mode/Channel Value Function THE following chart shows the functions and corresponding values for Green LED-array 64 : L254 each DMX channel according to mode whether Standard (St), Basic (Ba) 0-255 Green ( 0-Black , 255-100% Green ) or Extended (Ex):...
Page 15
DMX channel´s functions and their values (272 DMX channels) DMX channel´s functions and their values (272 DMX channels) Mode/Channel Value Function Mode/Channel Value Function Color Presets Dimmer: 112-113 Chase 52 0-255 Dimmer 0% to 100% 114-115 Chase 53 Chase Patterns: 116-117 Chase 54 0--9...
Clean the glass of the fixture with a slightly damp soft cloth. When necessary, use a non-alcohol-based glass cleaner. Never use harsh When you turn on the DREAMPANEL TWIN, it will first perform an solvents! automatic reset. The display may show “Err channel is XX” indicating there is a problem with one or more of the channels.
FOAM FOR FLIGHT CASE • Information menu including: timer, temperature, software version, etc. VIDEO SOURCE DREAMPANEL TWIN is delivered in a carton packed with a dense, protective foam surrounding the fixture. This reusable protective shell is • 4096 Multi-chip RGB LED 30mW intended for a flight case that can be custom built for the luminaire.
In addition, cosmetic defects caused by the normal wear and tear of the unit are not covered under the warranty. Any modification to the fixture will void the warranty. AYRTON cannot under any circumstances be held liable for quality and conformity regarding the installation of this product, which is the responsibility of the installer.
Need help?
Do you have a question about the DREAMPANEL TWIN and is the answer not in the manual?
Questions and answers