Maintenance - Chicco URBAN PLUS Instructions For Use Manual

Wash by hand in cold water
Do not bleach
Do not tumble dry
Do not iron
Do not dry clean

MAINTENANCE

Lubricate the moving parts only if necessary, with a light
application of a silicone based lubricant. Regularly check
the condition of the wheels and, keep them clean from
dust and sand. Make sure that all plastic parts that slide on
the metal tubes are clean from dust, dirt and sand, in order
to avoid frictions that may compromise the optimal perfor-
mance of the stroller. Keep the stroller in a dry place.
FIRST ASSEMBLY OF THE STROLLER
1. Press the grey button inside the circular articulated joint
and at the same time, rotate the handle tube as shown in
figure 1.
2. Then extend the structure completely, by opening the
front leg tube until hearing a locking click (fig. 2-2A).
3. Insert the front wheel into the appropriate hole until hearing
a locking click (Fig. 3). Repeat the same operation for the
second front wheel.
4. To assemble the rear wheels Insert the wheel's pin into
the rear leg tube as shown in fig. 4. Repeat the same opera-
tion for the other wheel.
WARNING: Before using the stroller, make sure that the
wheels are well secured to the structure.
5. The front part of the basket has a shaped area. Assemble
the basket positioning the shaped part on the front tube,
using the relative press stud buttons (fig. 5) and repeat the
operation for the rear part of the basket (fig. 5A). To com-
plete the assembly, thread the straps located on the front
part of the basket through the "D''-shaped rings located on
the front legs of the stroller, securing the straps with the
press stud buttons (fig. 5B).
ASSEMBLY OF THE SEAT: STROLLER CONFIGURATION
The packaging includes the disassembled stroller frame
and closed seat.
6. To fit the seat on the stroller, open it acting on it as shown
in figures 6 – 6A until you hear the locking click (fig. 6B). To
complete opening the seat, close the zip around the metal
support under the seat as shown in fig. 6C-6D.
7. Fasten the buckle A, placed externally in the area of the
seat near the child's feet as shown in Fig. 7; Then fasten
buckle B, located under the seat (Fig. 7A).
8. To attach the seat, introduce the two hooks shown in Fig.
8 in the relative slots located inside the circular articulated
joints of the stroller (fig. 8A) until hearing a locking click.
WARNING: Make sure the seat is installed properly by pulling
it upwards.
9. The seat can be assembled on the stroller in both direc-
tions: in forward facing configuration (Fig. 9) and parent
facing configuration (fig. 9A).
10. To remove the seat, press the grey side buttons and pull
upward (fig. 10). These operations must not be performed
when the child is inside the seat.
WARNING: Do not remove the seat from the stroller when
the child is inside it.
SEAT ADJUSTMENTS
Once the seat is fit on the frame, it can be reclined in three
different positions.
11. The entire seat can be adjusted by pressing simultane-
ously the buttons located above the central articulated
joint (fig. 11).
12. The angle of the backrest can be adjusted compared to
the seat, by pressing the button as shown in fig. 12.
LEGREST ADJUSTMENTS
13. It is possible to adjust the leg rest in various positions,
by pressing simultaneously the buttons shown in fig. 13.
REMOVABLE BUMPER BAR
The stroller is equipped with removable bumper bar.
14. To remove it, press the buttons located on the sides (fig.
14).
15. To position and remove the child, unhook the bar from
one side only (fig. 15).
WARNING: Always fasten the safety belts. The bar IS NOT a
device for containing your child.
WARNING: The bar must not be used to lift the stroller
with the child inside of it.
HOW TO USE THE SAFETY HARNESS
The stroller is equipped with a retaining system with five
anchoring points, consisting of two shoulder straps, two
adjusting slots, a waist belt and a crotch strap with buckle,
already assembled.
WARNING: To adapt the belts to the body of the child, use
the shoulder straps, passing them through the two regula-
tion holes as indicated in Fig. 16.
16. After laying the child in the stroller, fasten the belts by
threading first the two forks inside the shoulder straps' slot
(fig. 16A) and then introduce them inside the crotch strap
buckle (fig. 16B); Adjust the length of the straps, ensuring
that they adhere to the child's shoulders and body correctly.
17. To unfasten the waist belt, press and pull the lateral forks
(fig. 17).
18. The waist belt must always be passed through the 2 D-
shaped rings on the sides of the stroller seat (fig. 18).
WARNING: Always use the restraint systems. For the safety
of your child use all five fixing points of the safety harness
belts.
REMOVING THE SAFETY BELTS
The safety belts can be removed (to be washed or used in
To remove the belts, unfasten the waist belt from the rela-
tive "D''-shaped rings and the shoulder straps from the fab-
ric slots located on the backrest. After removing the safety
belts, make sure that the belts are re-assembled properly
using the anchoring points.
20