Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for LTS LTD8304K-ET
Summary of Contents for LTS LTD8304K-ET
- Page 1 Digital Video Recorder Quick Start Guide...
-
Page 2: Table Of Contents
Digital Video Recorder Quick Start Guide TABLE OF CONTENTS Chapter1 Panels Description ........................6 1.1 Front Panel ............................ 6 1.2 Rear Panel ............................. 8 Chapter 2 Installation and Connections ..................... 10 2.1 DVR Installation ..........................10 2.2 Hard Disk Installation ........................10 2.3 RS-485 and Controller Connection.................... - Page 3 Digital Video Recorder Quick Start Guide Quick Start Guide About this Manual This Manual is applicable to LTD83XXK-ET and LTD85XXK-ST Series HD-TVI Digital Video Recorder (DVR). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
-
Page 4: Regulatory Information
Digital Video Recorder Quick Start Guide Regulatory Information FCC Information Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. - Page 5 Digital Video Recorder Quick Start Guide Applicable Models This manual is applicable to the models listed in the following table. Series Model LTD8304K-ET LTD83XXK-ET LTD8308K-ET LTD8316K-ET LTD8504K-ST LTD85XXK-ST LTD8508K-ST LTD8516K-ST Symbol Conventions The symbols that may be found in this document are defined as follows.
-
Page 6: Safety Instructions
Digital Video Recorder Quick Start Guide Safety Instructions Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user. In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. -
Page 7: Chapter1 Panels Description
Digital Video Recorder Quick Start Guide Chapter1 Panels Description 1.1 Front Panel The front panel vaires according to different models. Please refer to the actual product. Figure 1-1 Front Panel Table 1-1 Description of Front Panel Name Function Description POWER: The POWER indicator turns green when NVR is powered up. - Page 8 Digital Video Recorder Quick Start Guide Name Function Description Enter numeral “5”; Enter letters “JKL”; 5/JKL/EDIT: Delete characters before cursor; Check the checkbox and select the ON/OFF switch; Start/stop record clipping in playback. Enter numeral “6”; 6/MNO/PLAY: Enter letters “MNO”; Playback, for direct access to playback interface.
-
Page 9: Rear Panel
Digital Video Recorder Quick Start Guide Name Function Description And in auto sequence view mode, the buttons can be used to pause or resume auto sequence. Receiver for IR remote. IR Receiver 1.2 Rear Panel The rear panel vaires according to different models. Please refer to the actual product. ... - Page 10 Digital Video Recorder Quick Start Guide RCA connector AUDIO IN RS-485 Connector for RS-485 devices. DC 12V power supply. Power Supply Power Switch Switch for turning on/off the device. Ground. Connector for alarm input/output. Alarm In/Out...
-
Page 11: Chapter 2 Installation And Connections
Digital Video Recorder Quick Start Guide Chapter 2 Installation and Connections 2.1 DVR Installation During installation of the DVR: Use brackets for rack mounting. Ensure ample room for audio and video cables. When routing cables, ensure that the bend radius of the cables are no less than five times than its diameter. - Page 12 Digital Video Recorder Quick Start Guide Figure 2-1 Remove Cover Step 2 Connect one end of the data cable to the motherboard of DVR and the other end to the HDD. Figure 2-2 Connect Data Cable Step 3 Connect the power cable to the HDD. Figure 2-3 Connect Power Cable Step 4 Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
- Page 13 Digital Video Recorder Quick Start Guide Figure 2-4 Fix Hard Disk Step 5 Re-install the cover of the DVR and fasten screws.
-
Page 14: Rs-485 And Controller Connection
Digital Video Recorder Quick Start Guide 2.3 RS-485 and Controller Connection Typical Connection: Figure 2-5 Controller Connection A To connect PTZ to the DVR: Step 1 Disconnect pluggable block from the RS-485 terminal block. Step 2 Press and hold the orange part of the pluggable block; insert signal cables into slots and release the orange part. -
Page 15: Hdd Storage Calculation Chart
Digital Video Recorder Quick Start Guide 2.4 HDD Storage Calculation Chart The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate. - Page 16 Digital Video Recorder Quick Start Guide Bit Rate Storage Used 128K 160K 192K 224K 256K 112M 320K 140M 384K 168M 448K 196M 512K 225M 640K 281M 768K 337M 896K 393M 1024K 450M 1280K 562M 1536K 675M 1792K 787M 2048K 900M 4096K 1.76G 8192K...
-
Page 17: Chapter 3 Menu Operation
Digital Video Recorder Quick Start Guide Chapter 3 Menu Operation 3.1 Menu Structure The menu structure varies according to different models. Menu Playback Maintenance Shutdown Export VCA Search Record Camera Configuration Manual Behavior Normal Normal Schedule Camera General System Info Logout Record General... -
Page 18: Activating Your Device
Digital Video Recorder Quick Start Guide Step 2 Press the POWER button on the front panel. The Power LED should turn blue. The unit will begin to start. After the device starts up, the wizard will guide you through the initial settings, including modifying password, date and time settings, network settings, HDD initializing, and recording. - Page 19 Digital Video Recorder Quick Start Guide STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.
-
Page 20: Using The Unlock Pattern For Login
Digital Video Recorder Quick Start Guide Figure 3-6 Export GUID Step 5 After exporting GUID, the Attention box pops up as below. Click Yes to duplicate the password or No to cancel it. Figure 3-7 Duplicate the Password 3.4 Using the Unlock Pattern for Login For the Admin user, you can configure the unlock pattern for device login. -
Page 21: Login And Logout
Digital Video Recorder Quick Start Guide Connect at least 4 dots to draw the pattern. Each dot can be connected for once only. Step 2 Draw the same pattern again to confirm it. When the two patterns match, the pattern is configured successfully. - Page 22 Digital Video Recorder Quick Start Guide Clear-text password is supported. Click the icon and you can see the clear text of the password. Click the icon again and the content of the password restores invisible. In the Login interface, for the admin, if you have entered the wrong password for 7 times, the account will be locked for 60 seconds.
-
Page 23: User Logout
Digital Video Recorder Quick Start Guide Figure 3-14 Reset Password 2) Input the new password and confirm the password. 3) Click OK to save the new password. Then the Attention box pops up as shown below. Figure 3-15 GUID File Imported 4) Click OK and the Attention box as below pops up to remind you to duplicate the password of the device to IP cameras that are connected with default protocol. -
Page 24: Using The Setup Wizard
Digital Video Recorder Quick Start Guide Menu > Shutdown Figure 3-17 Logout Step 2 Click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system. 3.6 Using the Setup Wizard The Setup Wizard can walk you through some important settings of the device. - Page 25 Digital Video Recorder Quick Start Guide channels and types and the connectable maximum IP camera number, and configure 5 MP long distance transmission. Step 1 Enter the Signal Input Status interface. Menu > Camera > Signal Input Status Figure 3-19 View Signal Input Type Step 2 View the analog signal input channels and types, and the connectable maximum IP camera number.
-
Page 26: Network Settings
Digital Video Recorder Quick Start Guide 3.8 Network Settings Purpose: Network settings must be properly configured before you operate DVR over network. Step 1 Enter the Network Settings interface. Menu > Configuration > Network Figure 3-21 Network Settings Step 2 Select the General tab. Step 3 In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server. - Page 27 Digital Video Recorder Quick Start Guide Ensure the network connection is valid and correct, and the IP camera to add has already been activated. Please refer to the User Manual for activating the inactive IP camera. You can select one of the following three options to add the IP camera. ...
-
Page 28: Live View
Digital Video Recorder Quick Start Guide Step 2 Select the detected IP camera and click the Add button to add it directly, and you can click the Search button to refresh the online IP camera manually. OPTION 3: You can choose to custom add the IP camera by editing the parameters in the corresponding text field and then click the Add button to add it. -
Page 29: Playback
Digital Video Recorder Quick Start Guide Step 2 Click the Yes button in the pop-up Attention message box to confirm the settings. All the channels will start to record in the selected mode. 3.12 Playback The recorded video files and pictures on the hard disk can be played back in the following modes: instant playback, all-day playback for the specified channel, and playback by normal/event/smart/tag/system logs/sub-periods/external file search/picture. - Page 30 Digital Video Recorder Quick Start Guide Figure 3-25 Show VCA Information in Smart Playback Step 4 (Optional) Select the channel(s) to execute simultaneous playback of multiple channels.
-
Page 31: Chapter 4 Accessing By Web Browser
Digital Video Recorder Quick Start Guide Chapter 4 Accessing by Web Browser You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection. If the product does not work properly, please contact with your dealer or the nearest service center. - Page 32 Digital Video Recorder Quick Start Guide STRONG PASSWORD RECOMMENDED–We highly recommend you create a strong password of your own choosing (Using a minimum of 8 characters, including at least three of the following categories: upper case letters, lower case letters, numbers, and special characters.) in order to increase the security of your product.