Incorrect Code Lockout; Restoring Factory Defaults - ACT 10 Operating & Installation Instructions Manual

ACT 10 Digital Keypad Operating & Installation Instructions

Incorrect Code Lockout

lockout mode for 20 seconds. During this time, the red LED indicator will flash and all PIN codes will be inactive.
Enter Programming Mode followed by
settings. If the Programming Code has been forgotten, it may be set to 9999 by:
1. Remove the power from the unit.
2. Remove link LK1 at the back of the unit.
3. Apply power to unit.
Note: The keypad will not operate correctly without LK1 in place.
Figure 1: Typical ACT 10 Configuration
Figure 1: Typical ACT 10 Configuration
Door Release
Button
Door Release
Button
Door Contact
Volt - Free
Door Contact
Tamper Contacts
Volt - Free
Tamper Contacts
The ACT 10 may be used to control 2 doors as illustrated in the diagram above
When three invalid codes have been entered in a row, the keypad will enter

Restoring Factory Defaults

Power up without link if
Programming Code has
been lost
Power up without link if
Programming Code has
been lost
LK1
OM
R O N
LK1
5 A
5 A
3 0 V
0V
Interlock
OM
R O N
(PB2)
Push
5 A 2 5 0 V
Button
5 A DC
3 0 V
Door
Contact
0V
B a t c h : 2 0 x x - 1
Interlock
P r o d u c t : A C T 1 0 R e v 3 . 0
(PB2)
S e r i a l N o . 1 2 3 4 5
Push
Button
0 1 2 3 4 5 6 7 8 9
Door
Contact
B a t c h : 2 0 x x - 1
P r o d u c t : A C T 1 0 R e v 3 . 0
S e r i a l N o . 1 2 3 4 5
0 1 2 3 4 5 6 7 8 9
Door Release Button
for Door 2
Door Release Button
for Door 2
. This restores the ACT 10 Digtal Keypad to its default
4. Replace link LK1.
5. Proceed with programming.
Shows connection for normally
DE-ENERGISED lock, (e.g. door-strike).
Shows connection for normally
DE-ENERGISED lock, (e.g. door-strike).
+
-
N/C
C
OM N/O
R O N +
A C 5 A A C
2 5 0 V 2 5 0 V
-
5 A
DC DC
3 0 V
N/C
C
0V
OM N/O
R O N
Buzzer
A C 5 A A C
2 5 0 V
OP3
5 A
DC
3 0 V
Duress
OP2
Interlock
0V
Buzzer
OP3
Duress
OP2
Interlock
N/O
C
N/C
N/O
C
N/C
Break Glass
Unit (optional)
Shows connection for normally
Shows connection for normally ENERGISED
energised lock, (e.g. magnetic lock).
lock (e.g. magnetic lock)
Break Glass
6
Unit (optional)
Shows connection for normally ENERGISED
+V
Power Supply
12-24V ACDC
0V
+V
Power Supply
12-24V ACDC
0V
!
Important
Always Place Varistor
Across All Lock Terminals
+V
!
Important
Guest Buzzer
Output sink = 100mA max
Always Place Varistor
Across All Lock Terminals
+V
Guest Buzzer
Output sink = 100mA max
+V
Power Supply
12-24V ACDC
0V
+V
Power Supply
12-24V ACDC
0V
Door 2
Door 2