Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for 4IPNET EAP727
Summary of Contents for 4IPNET EAP727
- Page 1 EAP727 Enterprise Access Point...
-
Page 2: Copyright Notice
4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations. -
Page 3: Fcc Caution
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Copyright © 4IPNET, INC. All rights reserved. - Page 4 This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
-
Page 5: Package Contents
EAP727 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP727 is a high-end, dual radio 802.11 1. 4ipnet EAP727 x 1 b/g/n + ac MIMO Access Point (AP) with the best 2. Quick Installation Guide (QIG) x 1 performance for business and industrial applications 3. -
Page 6: System Overview
Internet. 802.3af PoE is also supported Restart / Reset Press once to restart the system; to reset the system to factory default settings, hold for more than 5 seconds. Copyright © 4IPNET, INC. All rights reserved. -
Page 7: Hardware Installation
Please follow the steps mentioned below to install the hardware of EAP727: 1. Place the EAP727 at the best location. The best location for EAP727 is usually at the center of your intended wireless network. Wall/Ceiling Mounting - Place the mounting bracket on a wall or ceiling - Mark the points where you will insert the screws. - Page 8 2. Connect the EAP727 to your network device. Connect one end of the Ethernet cable to the Uplink port of EAP727 and the other end of the cable to a switch, a router, or a hub. EAP727 is then connected to your existing wired LAN network.
-
Page 9: Getting Started
1. To access the Web Management Interface, connect the administrator PC to the Uplink port of EAP727 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP727 in TCP/IP of your PC, such as the following example: IP Address: 192.168.1.100... - Page 10 EAP727 Enterprise Access Point ENGLISH Administrator Login Page 4. After a successful login to EAP727, a System Overview page of the Web Management Interface will appear, as depicted below. The Web Management Interface - System Overview Page 5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the Administrator Login Page.
-
Page 11: Common Settings
Click on the Utilities icon on the main menu, and select the Change Password tab. Enter a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved. - Page 12 Determine the Band, Protocol and Channel settings: Select your preferred Band, Protocol and Channel for you wireless connection. For example, select 2.4GHz for the band, 802.11g+802.11n for the protocol and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
- Page 13 ENGLISH Admin should be aware of Dynamic Frequency Selection (DFS) mandated on some channels of the 5GHz band. When an EAP727 detects interference, this mechanism will limit the ability to broadcast the SSID on one of the channels listed below: ...
- Page 14 Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) EAP727 supports up to 16 virtual APs (VAPs) per RF Card. Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
- Page 15 Quick Installation Guide EAP727 Enterprise Access Point ENGLISH Virtual AP Overview Page Copyright © 4IPNET, INC. All rights reserved.
- Page 16 ENGLISH Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP727 supports up to 8 WDS links for connecting wirelessly to other WDS-capable APs (peer APs). By default, all WDS profiles are disabled. Click on the Wireless button on the main menu.
- Page 17 Congratulations! Now, 4ipnet EAP727 is installed and configured successfully. After EAP727's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments.