Hilti TE 60-AVR Manual
Hide thumbs
Also See for TE 60-AVR:
- Original operating instructions (250 pages) ,
- Manual (96 pages) ,
- Operating instructions manual (20 pages)
Related Manuals for Hilti TE 60-AVR
Summary of Contents for Hilti TE 60-AVR
- Page 1 TE 60-AVR TE 60-ATC/AVR English Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 2 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 3 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 4 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 5 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 6 TE 60-AVR TE 60-ATC/AVR Original operating instructions ........
- Page 7 Drilling without hammering action Drilling with hammering action (hammer drilling) Chiseling Chisel positioning Forward / reverse Protection class II (double-insulated) Protective earth / ground (only TE 60-AVR) Diameter English Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 8 Revolutions per minute 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
- Page 9 ▶ Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. ▶ Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power source, picking up or carrying the tool.
- Page 10 3.5 Undercut anchors The product is suitable for setting undercut anchors. Use only suitable setting tools. Detailed information on this topic can be obtained at your local Hilti Center. 3.6 Active Torque Control The tool is equipped with a mechanical slip clutch and an Active Torque Control (ATC) system.
- Page 11 3.11 Accessories and spare parts Further information about other system products ap- proved for use with your product can be found by scan- ning this QR code or online at: www.hilti.group. 4 Technical data 4.1 Combihammer When powered by a generator or transformer, the generator or transformer’s power output must be at least twice the rated input power shown on the rating plate of the power tool.
- Page 12 TE 60AVR TE 60-ATC/AVR Ø PCM diamond core bits •/• 42 mm … 102 mm Ø drill bits for metal 10 mm … 20 mm 10 mm … 20 mm Ø Drill bits for wood 10 mm … 32 mm 10 mm …...
- Page 13 5.1.4 Fitting the accessory tool 1. Apply a little grease to the connection end of the accessory tool. ◁ Use only the recommended grease supplied by Hilti. Using the wrong grease can result in damage to the tool. 2. Push the accessory tool into the chuck as far as it will go (until it engages).
- Page 14 5.2.3 Mixing Note Use the mixing paddle only with the quick-release chuck. Use the mixing paddle only when the reduced power (50 %) setting is active. 1. Insert the quick-release chuck in the power tool’s chuck. 2. Fit the mixing paddle into the quick-release chuck. 3.
- Page 15 Check all visible parts and controls for signs of damage at regular intervals and make sure that they all function correctly. • Do not operate the electric tool if damaged or if its parts malfunction. Have the tool repaired by Hilti Service immediately. •...
- Page 16 Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information.
- Page 17 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...
- Page 18 *2134960* 2134960 Hilti = registered trademark of Hilti Corp., Schaan Pos. 2 | 20170511 Printed: 28.06.2017 | Doc-Nr: PUB / 5277961 / 000 / 01...