Advertisement
SmartCode at a Glance
Exterior
Lock
button
Keypad
SmartKey
Keyway
tool hole
Switches and Status LED colors
Switches
On
Off
1 2 3 4
Switch
Function
Door lock status LED blinks every 6
1
seconds
Lock automatically re-locks door 30
2
seconds after unlocking. Disabled if no
codes are programmed.
3
Audio
4
Not used.
Deleting a single user code
Note: All codes may be deleted at once if the mastercode is enabled. For more information about the
mastercode, consult the online Programming and Troubleshooting Guide.
1 Keep door open.
2 Press Lock
Press Program
button once.
button once.
5 Re-enter user code.
6 Press Lock
button once.
If no button is pressed for five seconds, the system will time out, and
you will need to restart the procedure.
Important Safeguards
1.
Read all instructions in their entirety.
2. Familiarize yourself with all warning and caution statements.
3. Remind all family members of safety precautions.
4. Protect your user codes and mastercode.
5. Dispose of used batteries according to local laws and regulations.
CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel
can change the user codes, you must restrict access to the back panel and routinely
check the user codes to ensure they have not been altered without your knowledge.
The use of a mastercode can help protect your system's settings.
WARNING: This Manufacturer advises that no lock can provide complete security
by itself. This lock may be defeated by forcible or technical means, or evaded by
entry elsewhere on the property. No lock can substitute for caution, awareness of
your environment, and common sense. Builder's hardware is available in multiple
performance grades to suit the application. In order to enhance security and reduce
risk, you should consult a qualified locksmith or other security professional.
Reference Guide
Interior (cover removed)
Back
panel
Program
button
Switches
Status
LED
Turnpiece
shaft
Note: When the cover is removed,
the turnpiece shaft can be used to
manually lock and unlock the door.
Status
LED
Color
Lock Status
Blinking green
Unlocked
Blinking amber
Locked
Blinking red
Low battery
Door handing process
did not work properly.
Solid red
See the online
Programing and
Troubleshooting Guide.
3 Enter user code
4 Press Lock
to be deleted.
button once.
If unsuccessful
Test code
Make sure to enter
While the door is
the same valid code
open, test the user
in steps 3 and 5.
code to make sure
it no longer unlocks
the door.
System Alerts
Alert
Reason
One incorrect code entered.
No user code programmed.
Keypad flashes red three
times with three beeps*.
Programming timeout after five
seconds.
Unsuccessful programming.
Keypad flashes red 15 times
Three incorrect codes entered
with 15 beeps*
within one minute.
Keypad flashes red with fast
beeping sound for three to
Low battery.
four seconds.
Keypad flashes green with
Door jammed while attempting
continuous beeping sound
to lock.
for two seconds.
*Beeping sound will only be heard if switch #3 is on.
Troubleshooting
A complete Programming and Troubleshooting Guide is
available on the SmartCode 913 page at www.kwikset.com.
Factory Reset
A factory reset will delete all codes associated with the lock.
1 Remove
2 Press and HOLD the Program
battery pack.
3 Press the Program button
once more. In 20 seconds,
when the LED flashes green
and you hear one beep, the
lock has been reset.
4 / 4
Solution
Re-enter code.
Program at least one user code.
Attempt programming procedure again.
Re-enter code after 60 second keypad
lockout.
Replace batteries.
Manually re-lock door. If needed,
reposition strike.
button while reinserting
the battery pack.
Keep holding the button for 30
seconds until the lock beeps
and the status LED flashes red.
Status
LED
4 Perform the door handing process again
to teach the lock the orientation of the
door and add user codes to your lock.
© 2016 Spectrum Brands, Inc.
Advertisement
