Yamaha Clavinova CVP-405 Service Manual page 42

CVP-405/CVP-405PE/CVP-405PM
MB3516APF-G-BND-EF (X2314A00) RGB ENCODER
PIN
NAME I/O
NO.
1 GND1 -
2 R-IN I
3 G-IN I
4 B-IN I
5 N.C. -
6 fsc-IN I
7 NTSC/PAL-IN I
8 N.C. -
9 N.C. -
10 CSYNC-IN I
11 N.C. -
12 Vcc1 -
DM9000AEP (X7029A00) LAN CONTROLLER
PIN
NAME I/O
NO.
1 BGRES I/O
2 RXV -
DD25
3 RX+ I/O
4 RX- I/O
5 RXGND -
6 TXGND -
7 TX+ I/O
8 TX- I/O
9 TXV -
DD25
10 SD7 I/O
11 SD6 I/O
12 SD5 I/O
13 SD4 I/O
14 SD3 I/O
15 GND -
16 SD2 I/O
17 SD1 I/O
18 SD0 I/O
19 EEDIO I/O
20 EECK O
21 EECS O
22 SD15 I/O
23 V -
DD
24 SD14 I/O
AK4396VF-E2 (X8324A00) DAC (Digital to Analog Converter)
PIN
NAME I/O
NO.
-
1 DV
SS
-
2
DV
DD
I
3
MCLK
I
4
PDN
I
5
BICK
I
6 SDATA
I
7 LRCK
I
8
SMUTE/CSN
I
9
DFS0/CAD0
I
10
DEM0/CCLK
I
11 DEM1/CDTI
I
12 DIF0
I
13 DIF1
I
14
DIF2
42
FUNCTION
Ground
Analog R signal input
Analog G signal input
Analog B signal input
Not used
Subcarrier input
NTSC/PAL selector
Not used
Not used
Composite sync signal input
Not used
Power supply +5 V
FUNCTION
Bandgap pin
Power output +2.5 V
TP RX input
RX ground
TX ground
TP TX output
Power output +2.5 V
Processor data bus
Digital ground
Processor data bus
IO data to EEPROM
Clock to EEPROM
Chip select to EEPROM
Processor data bus
Digital power supply +3.3 V
Processor data bus
FUNCTION
Digital ground
Digital power supply +3.3 V
Master clock input
Power-down mode
Audio serial data clock
Audio serial data input
L/R clock
Soft mute/Chip select
Sampling speed mode select/Chip address 0
De-emphasis enable 0/Control data clock
De-emphasis enable 1/Control data input
Digital input format
PIN
NAME I/O
NO.
13 N.C. - Not used
14 N.C. - Not used
15 CROMA-OUT O Chrominance signal output
16 Y-OUT O Y-signal output
17 Y-TRAP - Luminance signal band control
18 N.C. - Not used
19 Vcc2 - Power supply +5 V
20 VIDEO-OUT O Composite video signal output
21 B-OUT O Analog B signal output
22 G-OUT O Analog G signal output
23 R-OUT O Analog R signal output
24 GND2 - Ground
PIN
NAME I/O
NO.
25 SD13 I/O
26 SD12 I/O
27 SD11 I/O Processor data bus
28 SD10 I/O
29 SD9 I/O
30 V - Digital power supply +3.3 V
DD
31 SD8 I/O Processor data bus
32 CMD I Command type
33 GND - Digital ground
34 INT O Interrupt request
35 IOR I Processor read command
36 IOW I Processor write command
37 CS I Chip select
38 LED2 O Link/Active LED
39 LED1 O Speed LED
40 PWRST I Power on reset
41 TEST I Operation mode
42 V - Digital power supply +3.3 V
DD
43 X2 O Crystal 25 MHz out
44 X1 I Crystal 25 MHz in
45 GND - Digital ground
46 SD I Fiber-optic signal detect
47 RXGND - RX ground
48 BGGND - Bandgap ground
PIN
NAME I/O
NO.
15 TTL I CMOS/TTL level select
16 VREFL I Low level voltage reference input
17 VREFH I High level voltage reference input
18 AV - Analog power supply +5 V
DD
19 AV - Analog ground
SS
20 AOUTR- O Rch negative analog output
21 AOUTR+ O Rch positive analog output
22 AOUTL- O Lch negative analog output
23 AOUTL+ O Lch positive analog output
24 VCOM O Common voltage output
25 P/S I Parallel/serial select
26 TST1/DZFL O Test 1/Lch zero input detect
27 TST2/CAD1 I Test 2/Chip address 1
28 ACKS/DZFR I/O Master clock auto setting mode/Rch zero input detect
DM: IC606
FUNCTION
DM: IC607
FUNCTION
DM: IC318
FUNCTION