Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for HP ProDesk 680 G3 MT
Summary of Contents for HP ProDesk 680 G3 MT
- Page 1 Maintenance and Service Guide HP ProDesk 680 G3 MT and HP ProDesk 600 G3 MT...
- Page 2 AMD is a trademark of Advanced Micro Devices, bound by the terms of the HP End User License Inc. Bluetooth is a trademark owned by its Agreement (EULA). If you do not accept these proprietor and used by HP Inc.
-
Page 3: About This Book
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. - Page 4 About This Book...
-
Page 5: Table Of Contents
Table of contents 1 Product features ............................1 Standard configuration features ........................... 1 Front panel components ............................2 Rear panel components ............................3 vPro systems ............................3 Non-vPro systems ..........................4 2 Illustrated parts catalog ..........................5 Serial number location ............................5 Computer major components .......................... - Page 6 4 Removal and replacement procedures ......................20 Preparation for disassembly ..........................20 Access panel ................................. 21 Dust filter ................................22 Front bezel ................................23 Internal drive bezel .............................. 24 Speaker ................................25 Card reader module ............................. 26 Hood sensor module ............................27 Serial port module ...............................
- Page 7 Creating recovery media ......................... 106 Creating recovery media using HP Recovery Manager (select models only) ....107 Creating recovery discs with HP Recovery Disc Creator (select models only) ..... 108 Creating recovery discs ................108 Backing up your information ..................108...
- Page 8 System Recovery when Windows is not responding ............ 110 System Recovery using recovery media (select models only) ........111 Using HP Recovery Disc operating system discs (select models only) ......111 Appendix A Battery replacement ........................113 Appendix B Statement of Volatility ........................ 116 Appendix C Power cord set requirements ......................
-
Page 9: Product Features
Product features Standard configuration features Features may vary depending on the model. For support assistance and to learn more about the hardware and software installed on the computer model, run the HP Support Assistant utility. Standard configuration features... -
Page 10: Front Panel Components
Front panel components 5.25-inch drive bay (behind bezel) USB 2.0 port with HP Sleep and Charge* Slim optical drive (optional) USB 2.0 port Dual-state power button USB 3.x ports (2) Hard drive activity light USB Type-C charging port Audio-out (headphone)/Audio-in (microphone) -
Page 11: Rear Panel Components
USB 3.x Ports (2) NOTE: If using a USB keyboard, HP recommends connecting the keyboard to one of the USB 2.0 ports with the Wake from S4/ S5 feature. When a device is plugged into the audio-in jack, a dialog box will open asking if you want to use the connector for a microphone line-in device or a headphone. -
Page 12: Non-Vpro Systems
USB 3.x Ports (2) NOTE: If using a USB keyboard, HP recommends connecting the keyboard to one of the USB 2.0 ports with the Wake from S4/ S5 feature. When a device is plugged into the audio-in jack, a dialog box will open asking if you want to use the connector for a microphone line-in device or a headphone. -
Page 13: Illustrated Parts Catalog
For use on computer models only in the People’s Republic of China Blank bezel Dust filter System boards (includes replacement thermal material): For use on HP ProDesk 680 G3 MT computer models: Equipped with the Windows 10 operating system and PCI slots Serial number location... - Page 14 Equipped with a non-Windows operating system and PCI slots Equipped with NetC operating system and PCI slots in the People’s Republic of China For use on HP ProDesk 600 G3 MT computer models: Equipped with the Windows 10 operating system Equipped with a non-Windows operating system Equipped with NetC operating system in the People’s Republic of China...
- Page 15 Description DVD-ROM Drive, 9.5-mm, slim DVD±RW SuperMulti Drive, 9.5-mm, slim Optical drive long bezel blank, 9.5-mm, slim Optical drive latch, 9.5-mm, slim Removable DP27 Kit, 9.5-mm, slim Networking: Intel 7265.NGWG.NV ac 2×2 + Bluetooth 4.0 LE PCIe + USB NGFF 2230 non-vPro Combo Adapter Intel ac 2×2 + Bluetooth 4.2 M.2 PCI-e + USB non-vPro Combo Adapter Intel ac 2×2 + Bluetooth 4.2 M.2 PCI-e + USB vPro Combo Adapter Intel PRO/1000 single port network interface card...
-
Page 16: Miscellaneous Parts
Power cord with C13 receptacle, 1.83-meter (6.00-feet) 5-15P for use in Thailand Power cord with C13 receptacle, 1.83-meter (6.00-feet) 6-amp for use in India Power cord with Option-949 adapter ROHS Adapters: HP DisplayPort–to–DVI SL adapter HP DisplayPort–to–HDMI 1.4 adapter Chapter 2 Illustrated parts catalog... - Page 17 Description HP DisplayPort–to–VGA adapter HP USB Type-C–to–DisplayPort adapter HP USB Type-C–to–USB 3.0 adapter Cables: DisplayPort cable (1.83-m) DVI–to–DVI monitor cable (RoHS) Hard drive SATA power cable (2×2-pin) Optical drive SATA power cable (2×2-pin) PS/2 plus serial port cable (200-mm) SATA cable (straight–to–right angle connector, 11-in) SATA cable (straight–to–right angle connector, RF solution, 11-in)
- Page 18 Description HP PS/2 slim Windows 8 keyboard: For use in Belgium For use in BHCSY For use in Bulgaria For use in Canada For use in the Czech Republic and Slovakia For use in Denmark For use in France For use in Germany...
- Page 19 For use in Taiwan For use in Thailand For use in Turkey For use in the United Kingdom and Singapore For use in the United States HP wireless Windows 8 keyboard, mouse, and dongle combination: For use in Canada Miscellaneous parts...
- Page 20 For use in Thailand For use in the United States HP Antimicrobial slim business keyboard for use in the People’s Republic of China HP USB slim business keyboard in grey finish for use in Germany USB PS/2 washable Windows 8 keyboard (BFR-PVC):...
-
Page 21: Routine Care, Sata Drive Guidelines, And Disassembly Preparation
Routine care, SATA drive guidelines, and disassembly preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system board. -
Page 22: Preventing Electrostatic Damage To Equipment
Preventing electrostatic damage to equipment Many electronic components are sensitive to ESD. Circuitry design and structure determine the degree of sensitivity. The following packaging and grounding precautions are necessary to prevent damage to electric components and accessories. ● To avoid hand contact, transport products in static-safe containers such as tubes, bags, or boxes. Protect all electrostatic-sensitive parts and assemblies with conductive or approved containers ●... -
Page 23: Recommended Materials And Equipment
Recommended materials and equipment The following grounding equipment is recommended to prevent electrostatic damage: ● Antistatic tape ● Antistatic smocks, aprons, or sleeve protectors ● Conductive bins and other assembly or soldering aids ● Conductive foam ● Conductive tabletop workstations with ground cords of one-megohm +/- 10% resistance ●... -
Page 24: Routine Care
Never cover the ventilation slots on the monitor with any type of material. ● ● Install or enable power management functions of the operating system or other software, including sleep states. Routine care General cleaning safety precautions Never use solvents or flammable solutions to clean the computer. Never immerse any parts in water or cleaning solutions;... -
Page 25: Cleaning The Monitor
The screws used in the computer are not interchangeable. They may have standard or metric threads and may be of different lengths. If an incorrect screw is used during the reassembly process, it can damage the unit. HP strongly recommends that all screws removed during disassembly be kept with the part that was removed, then returned to their proper locations. -
Page 26: Cables And Connectors
Batteries, battery packs, and accumulators should not be disposed of together with general household waste. In order to forward them for recycling or proper disposal, please use the public collection system or return them to HP. Chapter 3 Routine care, SATA drive guidelines, and disassembly preparation... -
Page 27: Sata Hard Drives
6.0 Gb/s SMART ATA drives The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for HP personal computers have built-in drive failure prediction that warns the user or network administrator of an impending failure (crash) of the hard drive. The SMART drive tracks fault prediction and failure indication parameters such as reallocated sector count, spin retry count, and calibration retry count. -
Page 28: Removal And Replacement Procedures
Removal and replacement procedures Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers. Preparation for disassembly WARNING! Voltage is always present on the system board when the computer is plugged into an active... -
Page 29: Access Panel
Access panel Prepare the computer for disassembly (see Preparation for disassembly on page 20). Position the computer with the rear toward you. Slide the access panel release latch (1) to the left. Use the access panel release handle (2) to pull the access panel back. Remove the access panel (3). -
Page 30: Dust Filter
Dust filter Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Stand the computer upright with the front facing toward you. Detach the dust filter from the front of the computer. Reverse this procedure to install the dust filter. -
Page 31: Front Bezel
Front bezel Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer in the horizontal mode with the front facing toward you. Release the three tabs (1) on the top of the front bezel from the computer chassis. Swing the top edge of the front bezel (2) away from the computer chassis. -
Page 32: Internal Drive Bezel
Internal drive bezel Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Remove the front bezel (see Front bezel on page 23). Release the tab (1) on the left side of the internal drive bezel that attaches to the front bezel. Remove the internal drive bezel (2). -
Page 33: Speaker
Speaker Follow these steps to remove the speaker: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer with the front panel toward you. Disconnect the speaker cable (1) from the system board. Remove the two Torx-15 M3.5×8.5 screws (2) that secure the speaker to the computer chassis. -
Page 34: Card Reader Module
Card reader module Follow these steps to remove the card reader module: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer with the front panel toward you. Disconnect the card reader module cable (1) from the system board. -
Page 35: Hood Sensor Module
Hood sensor module Follow these steps to remove the hood sensor module: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer with the rear panel toward you. Disconnect the hood sensor module cable (1) from the system board. -
Page 36: Serial Port Module
Serial port module Follow these steps to remove the serial port module: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer with the rear panel toward you. Disconnect the serial port module cable (1) from the system board. -
Page 37: Fan
Follow these steps to remove the speaker: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Position the computer with the rear panel toward you. Disconnect the fan cable (1) from the system board. Remove the three Phillips PM4.8×12.2 screws (2) that secure the fan to the computer chassis. -
Page 38: Hard Drives
Hard drives Follow these steps to remove a 2.5-inch hard drive: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Disconnect the hard drive power cable (1) from the 2.5-inch hard drive. Disconnect the hard drive data cable (2) from the 2.5-inch hard drive. - Page 39 Slide the 2.5-inch hard drive to the left as far as it will go, and then remove the 2.5-inch hard drive (3). Follow these steps to remove a 3.5-inch hard drive: Prepare the computer for disassembly (see Preparation for disassembly on page 20).
- Page 40 Release the retention clip (1) that secures the 3.5-inch hard drive to the drive cage. Lift the right side of the 3.5-inch hard drive (2) until it releases from the slots in the drive cage. Slide the 3.5-inch hard drive to the right as far as it will go, and then remove the 3.5-inch hard drive (3). Reverse this procedure to install the hard drives.
-
Page 41: Optical Drives
Optical drives Follow these steps to remove a 5.25-inch size optical drive: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Disconnect the optical drive power cable (1) from the optical drive. Disconnect the optical drive data cable (2) from the optical drive. - Page 42 Slide the optical drive (2) out of the optical drive bay. Follow these steps to remove a slim optical drive: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21).
- Page 43 Slide the optical drive (2) out of the optical drive bay. Reverse this procedure to install the optical drives. Optical drives...
-
Page 44: Drive Cage
Drive cage Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Disconnect all cables to drives installed in the drive cage (see Hard drives on page 30 Optical drives on page 33). -
Page 45: Memory Module
Memory module The computer has three memory module sockets. CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to drain before adding or removing memory modules. Regardless of the power-on state, voltage is always supplied to the memory modules as long as the computer is plugged into an active AC outlet. -
Page 46: Expansion Card
Expansion card The computer has two PCI Express x1 expansion sockets and two PCI Express x16 expansion sockets. NOTE: The PCI Express sockets support only low profile cards. You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 sockets. For dual graphics card configurations, the first (primary) card must be installed in the PCI Express x16 sockets. - Page 47 If you are installing an expansion card in a vacant PCI Express x1 socket, insert a flatblade screwdriver into the slots on the rear of expansion slot cover (1) and rock the slot cover back and forth to break it free from the chassis (2). Expansion card...
- Page 48 If you are installing an expansion card in a vacant PCI Express x16 socket, remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. Store the removed card in anti-static packaging.
-
Page 49: Power Supply
Power supply Follow these steps to remove the power supply: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Remove the drive cage (see Drive cage on page 36). -
Page 50: Fan-Sink
Fan-sink NOTE: The fan-sink spare park kit includes replacement thermal material. Follow these steps to remove the fan-sink: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Remove the drive cage (see Drive cage on page 36). - Page 51 Reverse this procedure to install the fan-sink. Fan-sink...
-
Page 52: Processor
Processor NOTE: The processor spare park kit includes replacement thermal material. Follow these steps to remove the processor: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21). Remove the drive cage (see Drive cage on page 36). -
Page 53: System Board
System board NOTE: The system board spare park kit includes replacement thermal material. Follow these steps to remove the system board: Prepare the computer for disassembly (see Preparation for disassembly on page 20). Remove the access panel (see Access panel on page 21), and then remove the following components: Drive cage (see Drive cage on page... - Page 54 Remove the eight Torx-15 M3.3×8.9 screws that secure the system board to the computer chassis. Slide the system board (1) forward through the opening in the front of the computer chassis. Swing the rear edge of the system board (2) up and forward until the components on the rear edge are clear of the rear panel.
-
Page 55: Computer Setup (F10) Utility
Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: ● Change settings from the defaults or restore the settings to default values. View the system configuration, including settings for processor, graphics, memory, audio, storage, ●... - Page 56 Use the arrow (left and right) keys to select the appropriate heading. Use the arrow (up and down) keys to select the option you want, then press Enter. To return to the Computer Setup Utilities menu, press Esc. To apply and save changes, select Main > Save Changes and Exit. ●...
-
Page 57: Computer Setup-Main
Integrated MAC Address System Diagnostics If the hard drive has the HP Advanced Diagnostics installed, the application will launch. If HP Advanced Diagnostics is not installed, then a basic version built into the BIOS will provide the capability to perform the following functions: ●... - Page 58 ● Update BIOS Using Local Media Lets you access files on either USB storage or the hard drive. The HP BIOS Update and Recovery application included in BIOS Softpaqs at www.hp.com will copy the BIOS file to the correct location on the hard drive or USB device.
-
Page 59: Computer Setup-Security
Computer Setup—Security NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 5-2 Computer Setup—Security Option Description Set up BIOS Lets you set and enable a BIOS administrator password, which includes the following privileges: Administrator Password ●... - Page 60 Table 5-2 Computer Setup—Security (continued) Option Description ● Data Recovery Policy Select ‘Automatic’ or ‘Manual’ to set data recovery policy. ‘Manual’ lets you select whether or not to execute recovery of a corrupted region if it is detected. Set Up BIOS Power-On Lets you set and enable a BIOS power-on password.
-
Page 61: Computer Setup-Advanced
Table 5-2 Computer Setup—Security (continued) Option Description Default is ‘Unlock’. Cover Removal Sensor (Disabled/Notify user/Administrator password) Lets you disable the cover sensor or configure what action is taken if the computer cover was removed. Default is ‘Disabled’. NOTE: Notify user alerts the user with a POST error on the first boot after the sensor detects removal of the cover. - Page 62 Table 5-3 Computer Setup—Advanced (for advanced users) (continued) Option Heading Default is enabled. Specify the order in which UEFI boot sources (such as a internal hard drive, USB hard drive, USB optical drive, or internal optical drive) are checked for a bootable operating system image.
- Page 63 Table 5-3 Computer Setup—Advanced (for advanced users) (continued) Option Heading Controls the virtualization features of the processor. Changing this setting requires turning the computer off and then back on. Default is disabled. Virtualization Technology (VTx) (Intel only) Controls the virtualization features of the processor. Changing this setting requires turning the computer off and then back on.
- Page 64 Table 5-3 Computer Setup—Advanced (for advanced users) (continued) Option Heading Select to show the device in the operating system. Default is enabled. Touch Panel Clear to disable the display panel touch feature. Default is enabled. Port Options Allows you to hide the following ports from the operating system: ●...
- Page 65 Table 5-3 Computer Setup—Advanced (for advanced users) (continued) Option Heading Enabling this feature reduces the power of the system as much as possible in the S5 state. Power is removed from the wake up circuitry, the expansion slots, and any management features while in S5. Default is disabled.
-
Page 66: Recovering The Configuration Settings
Table 5-3 Computer Setup—Advanced (for advanced users) (continued) Option Heading ● BIOS Watchdog Timer (min.) – (5/10/15/20/25). Default is 5 min. CIRA Timeout (min.) (1/2/3/4/Never) CIRA is Customer Initiated Remote Assistance, an Intel service to help users employing Active Management Technology (AMT). Recovering the Configuration Settings This method of recovery requires that you first perform the Save to Removable Media command with the Computer Setup (F10) Utility before Restore is needed. -
Page 67: Troubleshooting Without Diagnostics
To assist you in resolving problems online, HP Instant Support Professional Edition provides you with self- solve diagnostics. If you need to contact HP support, use HP Instant Support Professional Edition's online chat feature. Access HP Instant Support Professional Edition at: http://www.hp.com/go/ispe. -
Page 68: Helpful Hints
If it becomes necessary to call for technical assistance, be prepared to do the following to ensure that your service call is handled properly: Be in front of your computer when you call. ● ● Write down the computer serial number, product ID number, and monitor serial number before calling. ●... -
Page 69: Solving General Problems
● If you have installed an operating system other than the factory-installed operating system, check to be sure that it is supported on the system. ● If the system has multiple video sources (embedded, PCI, or PCI-Express adapters) installed (embedded video on some models only) and a single monitor, the monitor must be plugged into the monitor connector on the source selected as the primary VGA adapter. - Page 70 In case of forgotten password, power loss, or computer malfunction, you must manually disable the Smart Cover lock . A key to unlock the Smart Cover Lock is not available from HP. Keys are typically available from a hardware store.
- Page 71 Poor performance. Cause Solution Low on memory. Add more memory. Hard drive fragmented. Defragment hard drive. Program previously accessed did not release reserved memory Restart the computer. back to the system. Virus resident on the hard drive. Run virus protection program. Too many applications running.
- Page 72 System does not power on and the LEDs on the front of the computer are not flashing. Cause Solution System unable to power on. Press and hold the power button for less than 4 seconds. If the hard drive LED turns white, then: If equipped with a voltage selector, check that the voltage selector (located on the rear of the power supply) is set to the appropriate voltage.
-
Page 73: Solving Power Problems
Solving power problems Common causes and solutions for power problems are listed in the following table. Power supply shuts down intermittently. Cause Solution If equipped with a voltage selector, voltage selector switch on Select the proper AC voltage using the selector switch. rear of computer chassis (some models) not switched to correct line voltage (115V or 230V). -
Page 74: Solving Hard Drive Problems
Solving hard drive problems Hard drive error occurs. Cause Solution Hard disk has bad sectors or has failed. In Windows 7, click Start, click Computer, and right-click on a drive. Select Properties, and then select the Tools tab. Under Error-checking click Check Now. In Windows 10, type file in the taskbar search box, and then select File Explorer from the list of applications. - Page 75 Nonsystem disk/NTLDR missing message. Cause Solution The system is trying to start from the hard drive but the hard ▲ Perform Drive Protection System (DPS) testing in system drive may have been damaged. ROM. System files missing or not properly installed. Insert bootable media and restart the computer.
-
Page 76: Solving Media Card Reader Problems
Solving media card reader problems Media card will not work in a digital camera after formatting it in Windows. Cause Solution By default, Windows will format any media card with a capacity Either format the media card in the digital camera or select FAT greater than 32MB with the FAT32 format. -
Page 77: Solving Display Problems
Do not know how to remove a media card correctly. Cause Solution NOTE: Never remove the card when the green LED is flashing After installing the media card reader and booting to Windows, the reader and the inserted cards are not recognized by the computer. - Page 78 Reseat DIMMs. Power on the system. Replace DIMMs one at a time to isolate the faulty module. Replace third-party memory with HP memory. Replace the system board. Blank screen and the power LED flashes Red six times, once every second, followed by a two second pause, and the computer beeps six times.
- Page 79 Blank screen and the power LED flashes Red seven times, once every second, followed by a two second pause, and the computer beeps seven times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution System board failure (ROM detected failure prior to video). Replace the system board.
- Page 80 Image is not centered. Cause Solution Position may need adjustment. Press the monitor's Menu button to access the OSD menu. Select ImageControl/ Horizontal Position or Vertical Position to adjust the horizontal or vertical position of the image. “No Connection, Check Signal Cable” displays on screen. Cause Solution Monitor video cable is disconnected.
-
Page 81: Solving Audio Problems
To download a SoftPaq that will assist you with the synchronization, go to the following Web site, select the appropriate monitor, and download either SP32347 or SP32202: http://www.hp.com/support Graphics card is not seated properly or is bad (some models). Reseat the graphics card. Replace the graphics card. - Page 82 Sound does not come out of the speaker or headphones. Cause Solution The speakers should be plugged into the line-out jack and the headphones should be plugged into the headphone jack. External speakers plugged into the wrong audio jack on a recently See the sound card documentation for proper speaker connection.
-
Page 83: Solving Printer Problems
Line-in jack is not functioning properly. Cause Solution Jack has been reconfigured in the audio driver or application In the audio driver or application software, reconfigure the jack or software. set the jack to its default value. There is no sound or very weak sound is detected by the headset microphone. Cause Solution The incorrect style of headset is being used. -
Page 84: Solving Keyboard And Mouse Problems
Printer will not print. Cause Solution To run MS-DOS commands, press the Windows key + r, type cmd in the Open box, and then click OK. If you are on a network, you may not have made the connection Make the proper network connections to the printer. to the printer. - Page 85 Keyboard commands and typing are not recognized by the computer. Cause Solution Keyboard connector is not properly connected. Shut down the computer, reconnect the keyboard to the back of the computer, and then restart the computer. Program in use has stopped responding to commands. Shut down your computer using the mouse and then restart the computer.
- Page 86 Mouse will only move vertically, horizontally, or movement is jerky. Cause Solution Mouse roller ball or the rotating encoder shafts that make contact Remove roller ball cover from the bottom of the mouse and clean with the ball are dirty. the internal components with a mouse cleaning kit available from most computer stores.
-
Page 87: Solving Hardware Installation Problems
Solving hardware installation problems You may need to reconfigure the computer when you add or remove hardware, such as an additional drive or expansion card. If you install a plug and play device, Windows automatically recognizes the device and configures the computer. If you install a non-plug and play device, you must reconfigure the computer after completing installation of the new hardware. -
Page 88: Solving Network Problems
DIMM1 or XMM1 must always be installed. DIMM1 must be installed before DIMM2, and DIMM3 must be installed before DIMM4 Replace third-party memory with HP memory. Replace the system board. Solving network problems Some common causes and solutions for network problems are listed in the following table. These guidelines do not discuss the process of debugging the network cabling. - Page 89 Network status link light never flashes. NOTE: The network status light is supposed to flash when there is network activity. Cause Solution No active network is detected. Check cabling and network equipment for proper connection. Network controller is not set up properly. Check for the device status within Windows, such as Device Manager for driver load and the Network Connections applet within Windows for link status.
- Page 90 Table 6-2 Solving network problems (continued) Diagnostics passes, but the computer does not communicate with the network. Cause Solution To access Control Panel in Windows 7, click Start, and then select Control Panel. To access Control Panel in Windows 10, type control panel in the taskbar search box, and then select Control Panel from the list of applications.
- Page 91 System setup utility reports unprogrammed EEPROM. Cause Solution Unprogrammed EEPROM. Contact an authorized service provider. Solving network problems...
-
Page 92: Solving Memory Problems
Management Engine (ME) settings). To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a memory module. For those systems that support ECC memory, HP does not support mixing ECC and non-ECC memory. Otherwise, the computer will not boot the operating system. -
Page 93: Solving Usb Flash Drive Problems
Memory is installed incorrectly or is bad. Reseat DIMMs. Power on the system. Replace DIMMs one at a time to isolate the faulty module. Replace third-party memory with HP memory. Replace the system board. Solving USB flash drive problems If you encounter USB flash drive problems, common causes and solutions are listed in the following table. -
Page 94: Solving Front Panel Component Problems
Solving front panel component problems If you encounter problems with devices connected to the front panel, refer to the common causes and solutions listed in the following table. A USB device, headphone, or microphone is not recognized by the computer. Cause Solution Device is not properly connected. - Page 95 Unable to connect to the Internet. Cause Solution This is useful for having the browser remember some specific Click Internet Options. information that the Web server can later retrieve.) In the Browsing history section on the General tab, click the Delete button. Select the Cookies check box and click the Delete button.
-
Page 96: Solving Software Problems
If you have installed an operating system other than the factory-installed operating system, check to be sure it is supported on the system. If you encounter software problems, see the applicable solutions listed in the following table. Computer will not continue and the HP logo does not display. Cause Solution ROM issue - POST error has occurred. -
Page 97: Post Error Messages And Diagnostic Front Panel Leds And Audible Codes
POST error messages and diagnostic front panel LEDs and audible codes This appendix lists the error codes, error messages, and the various indicator light and audible sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error condition. - Page 98 Control panel message Description Recommended action RTC (real-time clock) battery may need to the problem persists, replace the RTC battery. be replaced. See the Removal and Replacement section for instructions on installing a new battery. 008–Microcode Patch Error Processor is not supported by the BIOS. Upgrade BIOS to proper version.
- Page 99 Run the Drive Protection erroneous error message.) System test under using F2 Diagnostics when booting the computer. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) POST numeric codes and text messages...
- Page 100 System test under using F2 Diagnostics when booting the computer. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) Back up contents and replace hard drive. 309 – 30C: Hard Disk 3–6: SMART Hard Drive Hard drive is about to fail. (Some hard drives...
- Page 101 Control panel message Description Recommended action Reconfigure card resources and/or run Computer Setup or Windows utilities. 419-Out of Memory Space for Option ROMs Recently added PCI expansion card contains an If a PCI expansion card was recently ▲ option ROM too large to download during POST. added, remove it to see if the problem remains.
-
Page 102: Interpreting System Validation Diagnostic Front Panel Leds And Audible Codes
Control panel message Description Recommended action 90B-Fan Failure The system has detected that a cooling fan is Reseat fan. not operating correctly. Reseat fan cable. Replace fan. 90D-System Temperature Thermal shutdown occurred. The system BIOS Make sure system has proper airflow. has detected your machine was previously shut down to avoid overheating. - Page 103 Number of long beeps/blinks Error category Thermal System board Patterns of blink/beep codes are determined by using the following parameters: ● 1 second pause occurs after the last major blink. ● 2 second pause occurs after the last minor blink. ●...
-
Page 104: Password Security And Resetting Cmos
If you lose or forget the password when in stringent security mode, the system can only be reset by System Management Command. This is a way for HP Service and Support to provide a secure method to access the BIOS and command a password reset for a specifically identified unit under the direction of the owner. -
Page 105: Resetting Cmos And/Or The Password Jumper
If you lose or forget the password when in stringent security mode, the system can only be reset by System Management Command. This is a way for HP Service and Support to provide a secure method to access the BIOS and command a password reset for a specifically identified unit under the direction of the owner. -
Page 106: Changing A Setup Or Power-On Password
Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet. With the power cord disconnected, press the power button again to drain the system of any residual power. -
Page 107: Deleting A Setup Or Power-On Password
When the key icon appears, type your current password, a slash (/) or alternate delimiter character, your new password, another slash (/) or alternate delimiter character, and your new password again as shown: current password/new password/new password NOTE: Type the new password carefully since the characters do not appear on the screen. Press Enter. -
Page 108: Using Hp Pc Hardware Diagnostics (Uefi)
Using HP PC Hardware Diagnostics (UEFI) HP PC Hardware Diagnostics is a Unified Extensible Firmware Interface (UEFI) that allows you to run diagnostic tests to determine whether the computer hardware is functioning properly. The tool runs outside the operating system so that it can isolate hardware failures from issues that are caused by the operating system or other software components. - Page 109 Select your computer, and then select your operating system. In the Diagnostic section, follow the on-screen instructions to select and download the UEFI version you want. Downloading HP PC Hardware Diagnostics (UEFI) to a USB device 101...
-
Page 110: 10 System Backup And Recovery
Use HP Recovery Manager to create HP Recovery media after you successfully set up the computer. This ● step creates a backup of the HP Recovery partition on the computer. The backup can be used to reinstall the original operating system in cases where the hard drive is corrupted or has been replaced. For... -
Page 111: Using Windows Tools
DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs. Do not use rewritable discs such as CD±RW, DVD±RW, double-layer DVD±RW, or BD-RE (rewritable Blu-ray) discs; they are not compatible with HP Recovery Manager software. Or, instead, you can use a high- quality blank USB flash drive. -
Page 112: Recovering Using Hp Recovery Manager
HP Recovery Manager software allows you to recover the computer to its original factory state by using the HP Recovery media that you either created or that you obtained from HP, or by using the HP Recovery partition (select products only). If you have not already created recovery media, see... -
Page 113: Using The Hp Recovery Partition (Select Products Only)
Using HP Recovery media to recover You can use HP Recovery media to recover the original system. This method can be used if your system does not have an HP Recovery partition or if the hard drive is not working properly. -
Page 114: Backing Up, Restoring, And Recovering In Windows 7
IMPORTANT: After you remove the HP Recovery partition, you will not be able to perform System Recovery or create HP recovery media from the HP Recovery partition. So before you remove the Recovery partition, create HP Recovery media; see Creating HP Recovery media (select products only) on page 102. -
Page 115: Creating Recovery Media Using Hp Recovery Manager (Select Models Only)
Click the Start button, click All Programs, click Security and Protection, click Recovery Manager, and then click HP Recovery Media Creation. If prompted, click Yes to allow the program to continue. Click Create recovery media using blank DVD(s), and then click Next. -
Page 116: Creating Recovery Discs With Hp Recovery Disc Creator (Select Models Only)
Creating recovery discs with HP Recovery Disc Creator (select models only) HP Recovery Disc Creator is a software program that offers an alternative way to create recovery discs on select models. After you successfully set up the computer, you can create recovery discs using HP Recovery Disc Creator. -
Page 117: System Restore
If you were not able to create system recovery DVDs or USB flash drive, you can order a recovery disc set from support. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. -
Page 118: System Recovery When Windows Is Responding
Disconnect all peripheral devices from the computer, except the monitor, keyboard, and mouse. Press the power button to turn on the computer. As soon as you see the HP logo screen, repeatedly press the key on your keyboard until the Windows is Loading Files…... -
Page 119: System Recovery Using Recovery Media (Select Models Only)
Using HP Recovery Disc operating system discs (select models only) Use the steps provided in this section if you used HP Recovery Disc Creator to create a Windows 7 operating system DVD and a Driver Recovery DVD. If you created recovery media using... - Page 120 To order a Windows 7 operating system DVD, contact support. Go to http://www.hp.com/support, select your country or region, and follow the on-screen instructions. CAUTION: Using a Windows 7 operating system DVD completely erases the hard drive contents and reformats the hard drive. All files that you have created and any software that you have installed on the computer are permanently removed.
-
Page 121: Appendix A Battery Replacement
The lithium battery is only used when the computer is NOT connected to AC power. HP encourages customers to recycle used electronic hardware, HP original print cartridges, and rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/recycle. - Page 122 Slide the replacement battery into position, positive side up. The battery holder automatically secures the battery in the proper position. Type 2 To release the battery from its holder, squeeze the metal clamp that extends above one edge of the battery. When the battery pops up, lift it out (1). To insert the new battery, slide one edge of the replacement battery under the holder’s lip with the positive side up.
- Page 123 Insert the new battery and position the clip back into place. NOTE: After the battery has been replaced, use the following steps to complete this procedure. Replace the access panel. Plug in the computer and turn on power to the computer. Reset the date and time, your passwords, and any special system setups using Computer Setup.
-
Page 124: Appendix B Statement Of Volatility
Download the latest BIOS (system ROM) from the HP website. Follow the instructions to flash the BIOS that are found on the website. Turn on the system, and while system is powering on, and after the HP splash screen, press the to enter BIOS setup screen. -
Page 125: Appendix C Power Cord Set Requirements
Power cord set requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage. -
Page 126: Country-Specific Requirements
Country-specific requirements Additional requirements specific to a country are shown in parentheses and explained below. Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) Austria (1) Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) Sweden (1) SEMKO Denmark (1) DEMKO... -
Page 127: Appendix D Specifications
Specifications Unit Value Chassis (in the desktop position) 3.7 in 95 mm Height 10.6 in 270 mm Width 11.8 in 300 mm Depth Approximate Weight 9.8 lb 4.43 kg Weight Supported (maximum distributed load in desktop position) 77 lb 35 kg Temperature Range 50°... -
Page 128: Index
22 card reader module HP PC Hardware Diagnostics (UEFI) removal and replacement 26 downloading 100 cautions electrostatic discharge (ESD) 13 HP Recovery Disc Creator, using 108 AC power 13 preventing damage 14 cables 18 error electrostatic discharge 13 installing... - Page 129 3, 4 7 106 audio-out 2 USB 2.0 2 recovery USB flash drive, steps for audio-out jack 3, 4 USB 2.0 with HP Sleep and creating Windows 7 107 headphone 2 Charge 2 removal and replacement microphone 2 USB 2.0 with Wake from S4/S5...
- Page 130 System Restore, Windows 7 109 temperature control 15 tools, servicing 17 Torx T-15 screwdriver 17 USB 2.0 port 2 USB 2.0 port with HP Sleep and Charge 2 USB 2.0 port with Wake from S4/S5 3, 4 USB 3.x port 2, 3, 4...