Advertisement

Quick Links

Wing Span:93 in /2326mm
Wing Area:110.7sq.dm;
Length:95 in / 2414.3mm;
CAUTION : this plane is not a toy and should be kept away
children under 16 years of age! Before use , please carefully read
this manual.
●First-time builders should seek advice from people having building
experience in order to assemble the model correctly and to produce its
performance to full extent .
●Assemble this kit only in places out of children's reach!
●Take enough safety percautions prior to operating this model.
You are responsible for this model's assembly and safe operation!
●Always keep this instruction manual ready at hand for quick
reference,even after completing the assembly.
Flying Weight:7800-8000g;
Radio:6Channel 6Servos;
Engine:60CC Gas
P.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EXTRA-330SC 60CC and is the answer not in the manual?

Questions and answers

Summary of Contents for Flight Model EXTRA-330SC 60CC

  • Page 1 Wing Span:93 in /2326mm Flying Weight:7800-8000g; Wing Area:110.7sq.dm; Radio:6Channel 6Servos; Length:95 in / 2414.3mm; Engine:60CC Gas CAUTION : this plane is not a toy and should be kept away children under 16 years of age! Before use , please carefully read this manual.
  • Page 2 MAIN WINGS Gather wing parts as shown. Install the aileron horns in place with AB glue. Install the servo after pulling the servo extention wire in the wing.Install the servo arm on the servo and loctitle it in place on the mount screw.Install the pushrod and control horn.
  • Page 3 STABILIZER AND RUDDER ● Stabilizer parts together ● Apply epoxy into hinge hole of the elevator ● Attach the servo extension wire using foam wire holding brackes or zip ties to the formers along the sides of the fuse so they can't interfere with the rudder control cables.
  • Page 4 Mount the servo arm on to the elevator push rod before installing it on the servo so you can tighten the nylon insert locking nut to the mounting screw. Slide the stab on to the alumium tube and attach to fuse using the bolts provided.
  • Page 5 ● Gather rudder parts as shown. ● Make sure to allow room for epoxy to penetrate the hinges. Carefully slide the rudder onto each hinge and against the trailing edge of the fin.Wipe away excess epoxy with alcohol wetted wipes. ●...
  • Page 6 ● Connect the main wings and the fuselage with CF tube MAIN LANDING GEAR AND TAIL WHEEL ● Gather landing gear parts as shown. ● Install the main landing gear with the bolts provided and use blind nuts already installed and use blue Loctite on the mounting bolts.
  • Page 7 ● Put the shield in the landing gear ● Drill holes , as shown ● Use screw to lock it...
  • Page 8 ● Install the wheel cover, and fix it up to landing gear with screw. The finished photo as shown.
  • Page 9 ● Gather tail wheel parts as shown. ● Use screw to lock tail landing gear on the wing bottom ● Measure the length of the engine from the firewall mounts to the prop thrust washer for the proper distance allowing 1/4" to 1/2" from the dege of the cowl.
  • Page 10: Fuel Tank

    ● Draw the engine ecnter line and thrust line darker with a ball point. Note the 2 degree right thrust built in to the firewall. ● The cowl is already built with this offset as well. ● Use the drill template if you are going to use a DLE 60 or measure your engines mounting location.
  • Page 11 ● Gather fuel tank parts as shown Velcro tank straps over foam. Install the fuel tank mounting ties under the fuel tank floor. Install the battery,receiver and switch in place as shown. P.11...
  • Page 12 CANOPY Slide the rubber backed washers on the hatch mounting bolts and insert bolts through the hatch mounting holes and into the fuse blind nuts.Tighten snugly but do not over tighten and crush the hatch or the fuse sides. COWLING Mount the cowl using the cowl mounting screws and rubber backed washers.the rubber...
  • Page 13 CG POSITION & CONTROL THROWS P.13...
  • Page 14 THE FINISHED PHOTO Another scheme for choice Flight Model MFG CO.,LTD ADD:No.10,Fu Ning Street,Xian Xi Industrial,Chang An Town,Dong Guan City,Guang Dong Province,China Tel: +86-769-85070618 / +86-769-85077880 Fax: +86-769-85091868 E-mail:info@flight-model.com Web: http://www.flight-model.com/products_list.html http://flight-model.en.alibaba.com/ P.14...
  • Page 15 P.15...
  • Page 16 P.16...
  • Page 17 P.17...
  • Page 18 P.18...
  • Page 19 P.19...
  • Page 20 P.20...
  • Page 21 P.21...
  • Page 22 P.22...
  • Page 23 P.23...
  • Page 24 P.24...
  • Page 25 P.25...
  • Page 26 P.26...
  • Page 27 P.27...
  • Page 28 P.28...

Table of Contents