Wyse WY-60 User Manual page 98

F-2
ANSI Personalities
Table F-1
ANSI Commands, Continued
Function Mnemonic
Command Sequence
WY-75NT100 VT52
Abort escape sequence, display error character
CAN CTRLX CTRLX
SUB or CTRL Z
or CTRL Z
Controlling the Terminal
Enter VT100 personality (from VT52 personality)
ESC
<
Terminal modes on (set) SM (1) ESC [Ps; ... ;Ps h
SM (2) ESC [ '1 Ps; ... ;Ps h
Terminal modes off (reset)3
RM
(1~
ESC [ Ps; ... ;Ps I
RM (2 ESC [ '1 Ps; ... ;Ps I
(1) PS4
Mode Mnemonic Defaultli (2) ?PS4 Mode Mnemonic
Default
1
Transfer enhanced data
B
GATM On 1
Cursor key
DECCKM Off
2 Keyboard lock KAM Off 2 VT100
7
DECANM NVR
3 Monitor CRM Off 3
132-column
DECCOLM NVR
4
Insert character
IRM Off 4 Smooth scroll DECSCLM NVR
6 Clear enhanced data
B
ERM On 5 Reverse screen DECSCNM
NVR
12 Local echo disable SRM NVR 6 Origin DECOM Off
13 Disable control execution FEAM Off 7 Character wrap DECAWM NVR
16 Cursor transfer termination TTM On (end-of-line wrap
20 Newline (received CR mode) LNM
NVR mode)
30 Display dIsable WYDSCM Off 8 Auto repeat (key DECARM NVR
31 Status line display WYSTLINM NVR repeat mode)
32 Screen saver WYCRTSAVM NVR
10 Block DECEDM NVR
33 Steady cursor WYSTCURM NVR 18 Print form feed DECPFF
Off
34 Underline cursor WYULCURM NVR 19 Print full screen DECPEX On
35 Width change clear disable WYCLRM NVR 25 Enable cursor DECTCEM NVR
40 Select 25th/43rd data line
WYSEDL NVR
41 Select 42/43 data lines WYSL44 NVR
42 WY-60 (from VT100 or WY60 NVR
WY-75
43
WY-75 (from
VT100~ WY75
NVR
44 VT100 (from WY-75 VT100
NVR
45 AUX data port WYDP NVR
Reset terminal to initial stateS
RIS ESC c
Reset all terminal modes s
WYSTR ESC I p
Sound bell
BEL CTRLG CTRLG
Keypad application mode on
DECKPAM
ESC
=
ESC
=
3. Final character in sequence is a lowercase L.
4..
Ps
values are listed in two groups; In the first group are the values for terminal modea that can be set with 8M command sequence (1)
or reset with RM command sequence (1); in the second group are the values for terminal modes that can be set with 8M sequence(2)
or reset with RM sequence (2). The latter group is shown as ? Ps to indicate that sequence (2) includes a question mark immediately
following the control sequence introducer CSI. Up to 16
Ps
values can be specified (separated by semicolons) in anyone 8M or RM
command sequence.
S. When terminal is turned on or reset.
"NVR~
signifies that the mode is on or off according to the value saved in nonvolatile memory.
6.
WY-7S personality only.
7. When off, VTS2 personality is enabled.
8. When Xon/Xoff handshaking is active, an Xon (DCI) character is sent after execution. of this command.