Eaton Power Xpert Meter 2000 Quick Start Manual

Eaton Power Xpert Meter 2000 Quick Start Manual

Gateway card kit
Hide thumbs Also See for Power Xpert Meter 2000:

Advertisement

Quick Start Guide
IL02601011E
Power Xpert® Meter 2000 Gateway
Card Kit

Table of Contents

Remove the Meter From Service . . . . . . . . . . . . . 2
Disconnect Power Connections, CTs, and
Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Remove Meter from Panel . . . . . . . . . . . . . . . . . 2
Locate the Meter on the Bench . . . . . . . . . . . . . 2
Install the Gateway Card . . . . . . . . . . . . . . . . . . . . 3
Check Meter Firmware . . . . . . . . . . . . . . . . . . . 4
Upgrade the Firmware . . . . . . . . . . . . . . . . . . . . 4
Configure the Gateway Card . . . . . . . . . . . . . . . . 5
Check Gateway Card Indicators . . . . . . . . . . . . . 5
using a Local PC . . . . . . . . . . . . . . . . . . . . . . . . . 5
Verify the IP Address . . . . . . . . . . . . . . . . . . . . . 7
Network Access . . . . . . . . . . . . . . . . . . . . . . . . . 7
Additional Information . . . . . . . . . . . . . . . . . . . . 8
Reinstall the Meter . . . . . . . . . . . . . . . . . . . . . . . . 8
PXM 2250
PXM 2260
IQ 250

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Power Xpert Meter 2000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Eaton Power Xpert Meter 2000

  • Page 1 PXM 2250 PXM 2260 Quick Start Guide IQ 250 IL02601011E Effective October 2009 IQ 260 Power Xpert® Meter 2000 Gateway Card Kit Table of Contents Remove the Meter From Service . . . . . . . . . . . . . 2 Disconnect Power Connections, CTs, and Modbus .
  • Page 2: Il02601011E Effective October

    For ANSI installations remove the four nuts and washers . Locate the Meter on the Bench The installation procedure requires local power and an active Ethernet connection . To provide power to the meter, it may be useful eaton corporation www.eaton.com...
  • Page 3: Install The Gateway Card

    (see the following figure) . Use care to correctly locate the card in the guides . Slide the card carefully into the meter until it stops . Gently push on the card until it “clicks” into place . eaton corporation www.eaton.com...
  • Page 4: Check Meter Firmware

    Place the CD that accompanied your upgrade kit into the PC’s CD/DVD drive . Install the Eaton Meter Configuration Software (double- click EatonMCSSetup .exe in the root folder of the Eaton Meter Configuration Software CD) . After installation, launch the Configuration Software .
  • Page 5: Configure The Gateway Card

    IP address, your network administrator will need to know the MAC address assigned to the meter . H caUtion eaton strongly recommends Using a fixed ip address (the defaUlt) if an eaton pxs system Will be accessing the meter. otherWise, eaton corporation www.eaton.com...
  • Page 6 Act may be flickering reflecting network activity) . The card’s default Ethernet IP address is 192 .168 .1 .1 . Set the PC’s address to an address on the same subnet, such as 192 .168 .1 .100 . eaton corporation www.eaton.com...
  • Page 7: Verify The Ip Address

    Notee: It may take around five minutes before the meter pages begin to display values . 11 . Login dialog box appears . 12 . The default Username is admin and the default Password is admin . Log in using these credentials . Figure 12. Login dialog eaton corporation www.eaton.com...
  • Page 8: Additional Information

    877-ETN-CARE (877-386-2273) Eaton .com © 2009 Eaton Corporation PowerChain Management is a registered All Rights Reserved trademark of Eaton Corporation . Printed in USA Publication No . IL02601011E All other trademarks are property of their September 2009 respective owners .

Table of Contents