Dahua K Series Quick Start Manual
Poe cube network camera
Hide thumbs
Also See for K Series:
- Quick start manual (13 pages) ,
- Quick start manual (16 pages) ,
- Quick start manual (17 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Quick Start Manual
Advertisement
Table of Contents
Related Manuals for Dahua K Series
Summary of Contents for Dahua K Series
- Page 1 Dahua K Series PoE Cube Network Camera Quick Start Guide V 1.0.0 Zhejiang Dahua Vision Technology CO., LTD...
-
Page 2: Important Safeguards And Warnings
Welcome Thank you for purchasing our Network camera! This user’s manual is designed to be a reference tool for your system. Please read the following safeguard and warnings carefully before you use this series product! Please keep this user’s manual well for future reference! Important Safeguards and Warnings 1．Electrical safety ... - Page 3 3. Operation and Daily Maintenance Please do not touch the heat dissipation component of the device directly in order to avoid scald. Please do not dismantle the device; there is no component which can be fixed by users themselves in the machine.
- Page 4 Please contact the customer service for the latest procedure and supplementary documentation. There may be deviation between the actual value of some data and the value provided in the manual due to the reasons such as the real environment is not stable and so on. Please refer to the company’s final explanation if there is any doubt or dispute.
-
Page 5: Table Of Contents
Table of Contents Product Structure ......................1 Device Components ..................1 Bidirectional talk ....................2 1.2.1 Device-end to PC-end................. 2 1.2.2 PC-end to the Device-end ................2 Alarm ......................... 3 Device Installation ......................5 Network Configuration ....................6 Modify IP Address ..................... 6 Login WEB Interface .................. -
Page 6: Product Structure
1 Product Structure 1.1 Device Components Figure 1-1 Figure 1-2 Figure 1-3 Please refer to the following sheet for more details about each port. Name Network port Reset button Alarm input/output Power port... -
Page 7: Bidirectional Talk
Built-in speaker Micro SD card slot Indicator light Built-in MIC IR LED Sheet 1-1 Note: For reset, long press for 8 seconds and then the light is off; please refer to the following sheet for more details about status of indicator light. Indicator light status Device status Red light normally on... -
Page 8: Alarm
Please go to the Master Volume interface of the PC to set first if you want to use the dual-way bidirectional talk. Please select Front Mic mode in the record control interface. (You can select microphone enhanced in advanced interface if the audio is too low.) 1.3 Alarm The alarm interface is shown as in Figure 1-4. -
Page 9: Step
Please refer to the following figures for alarm output information. See Figure 1-6 and Figure 1-7. Figure 1-6 Figure 1-7 Mode A: Level application. Alarm output high and low level, alarm output is OC; it needs to increase pull-up resistance externally to work normally. Max external pull-up level is 5V, max port current is 5mA. After external pull-up resistance is increased, the default of output signal is high level (external pull-up voltage), and it switches to low level when there is alarm output (when the working current is 5mA, output voltage is less than 0.8V). -
Page 10: Device Installation
2 Device Installation Important Please make sure the installation surface can min support the 3X weight of the camera and the bracket. Figure 2-1 Step 1 Paste the installation map on the installation surface such as wall, ceiling or the wood. Step 2 Dig holes in the installation surface according to the installation map. -
Page 11: Network Configuration
3 Network Configuration The IP address of all the cameras is the same when leaving factory (default IP192.168.1.108), in order to make the camera get access to the network smoothly, please plan the useable IP segment reasonably according to the actual network environment. 3.1 Modify IP Address IP address can be acquired and modified through quick configuration tool for the cameras which are accessed via wired network, it needs to connect wired network to configure wireless parameters... -
Page 12: Login Web Interface
Step 3 Modify the camera IP address on the “Net” interface, click “Save” to finish modification. See Figure 3-2 for more details. Figure 3-2 3.2 Login WEB Interface Note: Different devices may have different WEB interfaces, the figures below are just for reference, please refer to the document <<WEB Operation Manual>>... - Page 13 Figure 3-3 Step 3 Install controls according to the system prompt; see Figure 3-4 for the WEB main interface. Please modify the administrator password as soon as possible after you successfully logged in. Figure 3-4...
- Page 14 If there is any uncertainty or controversy, please refer to the final explanation of us. Please visit our website or contact your local service engineer for more information. Zhejiang Dahua Vision Technology Co., Ltd Address：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC. Postcode: 310053...
Need help?
Do you have a question about the K Series and is the answer not in the manual?
Questions and answers