Dahua SE-DIR13MP36 Quick Start Manual
Dahua SE-DIR13MP36 Quick Start Manual

Dahua SE-DIR13MP36 Quick Start Manual

Hd ir waterproof fixed ip dome camera

Advertisement

HD IR Waterproof Fixed IP Dome Camera
Quick Start Guide
Version 1.0.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SE-DIR13MP36 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Dahua SE-DIR13MP36

  • Page 1 HD IR Waterproof Fixed IP Dome Camera Quick Start Guide Version 1.0.0...
  • Page 2 Welcome Thank you for purchasing our IP camera! This quick start guide is designed to be a reference tool for your system. Please keep this start guide well for future reference. Please open the accessory bag to check the items one by one in accordance with the list below. Contact your local retailer ASAP if something is missing or damaged in the bag.
  • Page 3 Thunder-proof device is recommended to be adopted to better prevent thunder. The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera. 6. Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work.
  • Page 4: Table Of Contents

    Table of Contents Structure ............................1 Components ........................1 Framework and Dimension..................1 Device Installation ........................3 Installation Steps ......................3 Restore Factory Default Setup Introduction.............5 Quick Configuration Tool......................6 Overview ........................6 Operation ........................6 Web Operation..........................9 Network Connection.....................9 Login and Logout......................9 FAQ ............................12 Appendix Toxic or Hazardous Materials or Elements ...............13...
  • Page 5: Structure

    1 Structure 1.1 Components You can refer to the following figure for multiple-function combination cable information. See Figure Figure 1-1 Please refer to the following sheet for detailed information. Component Component Name Component 1 Device lens Component 2 Dome body Component 3 Dome enclosure Port Name...
  • Page 6 Please refer to the following two figures for dimension information. The unit is mm. See Figure 1-2 and Figure 1-3. Figure 1-2 Figure 1-3...
  • Page 7: Device Installation

    2 Device Installation 2.1 Installation Steps Important Before the installation, please make sure the installation environments can at least support 3x weight of the camera. Please follow the steps listed below to install the device. Please refer to Figure 2-1 for reference. Step 1 Turn clockwise to remove the decoration ring from the snap joints.
  • Page 8 Figure 2-2 Note This series product supports two cable exits. One is from the bottom and the other is from the side. Please refer to the following figure for cable exit from the side information. Figure 2-3 Please earth the GND port of the device to enhance the device reliability. The GND port is near the cable exit port on the rear of the dome.
  • Page 9: Restore Factory Default Setup Introduction

    Figure 2-4 2.2 Restore Factory Default Setup Introduction Important Please use RESET button when device is running. Step1 Please refer to step1 and step2 in chapter 2.1to loose the dome body. Push a little bit; you can take the dome body from the gland cover. Step2 Take the dome body out and then turn the top cover hard to remove.
  • Page 10: Quick Configuration Tool

    3 Quick Configuration Tool 3.1 Overview Quick configuration tool can search current IP address, modify IP address. At the same time, you can use it to upgrade the device. Please note the tool only applies to the IP addresses in the same segment. 3.2 Operation Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 3-1.
  • Page 11 Figure 3-2 Select the “Open Device Web” item; you can go to the corresponding web login interface. See Figure 3-3. Figure 3-3 If you want to modify the device IP address without logging in the device web interface, you can go to the configuration tool main interface to set.
  • Page 12 Figure 3-4 After you logged in, the configuration tool main interface is shown as below. See Figure 3-5. Figure 3-5 For detailed information and operation instruction of the quick configuration tool, please refer to the Quick Configuration Tool User’s Manual included in the resources CD.
  • Page 13: Web Operation

    4 Web Operation This series IPC product support the Web access and management via PC. Web includes several modules includes monitor channel preview, system configuration, alarm and etc. 4.1 Network Connection Please follow the steps listed below for network connection. Make sure the IPC has connected to the network properly.
  • Page 14 Figure 4-2 If it is your first time to login in, system pops up warning information to ask you whether install control webrec.cab or not after you logged in for one minute. Please click OK button, system can automatically install the control. When system is upgrading, it can overwrite the previous Web too. If you can’t download the ActiveX file, please check whether you have installed the plug-in to disable the control download.
  • Page 15 Figure 4-4 Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction.
  • Page 16: Faq

    5 FAQ I can not boot up Please click RESET button for at least five seconds to restore the device or factory default setup. operate properly. The water leakage The unauthorized front or rear cap remove many result in water occurred.
  • Page 17: Appendix Toxic Or Hazardous Materials Or Elements

    Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Cr VI PBDE Circuit Board ○ ○ ○ ○ ○ ○ Component Device Construction ○ ○ ○ ○ ○ ○ Material Wire and Cable ○ ○...

This manual is also suitable for:

Ipc-hdw2100p seriesIpc-hdw2100n series

Table of Contents