Table of Contents
Advertisement
Quick Links
TUBULAR SERIES
IS-875HT and IS-925HT
A I R C O M P R E S S O R S
IWATA STUDIO SERIES TUBULAR SERIES AIR COMPRESSORS — IS-875HT and IS-925HT
Congratulations on your new purchase! The Iwata Tubular Series Air Compressors deliver quiet,
clean, pulse free air along with superb moisture separation and precise air pressure adjustment.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Iwata IS-875HT
Summary of Contents for Iwata IS-875HT
- Page 1 A I R C O M P R E S S O R S IWATA STUDIO SERIES TUBULAR SERIES AIR COMPRESSORS — IS-875HT and IS-925HT Congratulations on your new purchase! The Iwata Tubular Series Air Compressors deliver quiet, clean, pulse free air along with superb moisture separation and precise air pressure adjustment.
-
Page 3: Need Assistance
If you have any issues with this product, call ANEST IWATA-MEDEA (U.S.A.) 503-253-7308 (M-F 8AM - 4:30PM Paci c Time) or your local ANEST IWATA a liate before returning to your place of purchase. ANEST IWATA-MEDEA, INC. ANEST IWATA CORPORATION ANEST IWATA AUSTRALIA PTY LTD. - Page 4 WARNING: Using a plug adapter and power converter may cause unit to overheat. Any issues resulting from the use of a power adapter and/or power converter are not covered under the Anest Iwata-Medea warranty.
- Page 5 EXPLODED DIAGRAM - SMART JET PLUS IS-875HT Unpack the compressor and all packaged components. Enclosed you’ll find: a. Smart Jet Plus Compressor (#IS-875HT) b. Moisture Filter Regulator c. Airbrush/Spray Gun Holder (with screws) d. Air Hose (#DT I 10) e. Adapter Kit (for other brands of airbrush)
- Page 6 EXPLODED DIAGRAM - POWER JET PLUS IS-925HT Unpack the compressor and all packaged components. Enclosed you’ll find: a. Power Jet Plus Compressor (#IS-925HT) b. Moisture Filter Regulator c. Airbrush/Spray Gun Holder (with screws) d. Air Hose (#DT I 10) e. Adapter Kit (for other brands of airbrush) f.
-
Page 7: Getting Started
Screw the straight air hose’s small end onto the airbrush. a. Note: If you’re using a brand of airbrush other than Iwata, use the appropriate adapter from the adapter kit. You might have to try them out to see which one is right. -
Page 8: Ending A Session
REGULATING THE PRESSURE When you first hook up your airbrush to your compressor and depress the trigger of your airbrush, the pressure that registers on your gauge is called your “working pressure. ” Your working pressure can vary depending on the size of your airbrush’s nozzle. The smaller the nozzle size, the higher your working pressure. -
Page 9: Maintenance
MAINTENANCE Releasing Built-Up Moisture • Release the water by twisting the dial toward the “–” sign. • This will open the bleed valve and drain off the collected moisture. • Hold a paper towel under the open valve to collect the water. •... -
Page 10: Troubleshooting
Both methods provide an airtight seal. If the air leak is in the middle of a hose the hose will need to be replaced. For any other problems or issues call or contact ANEST IWATA-MEDEA at 503-253-7308 or email at: info@iwata-medea.com... -
Page 11: Warranty
Genuine Iwata ©2016 Anest Iwata-Medea, Inc. All rights reserved. The Anest Iwata-Medea logo, Anest Iwata-Medea and Iwata Studio Series are registered trademarks of Anest Iwata-Medea, Inc. Iwata Custom Micron, Iwata Hi-Line and Iwata Eclipse are trademarks of ANEST IWATA Corporation. Iwata, the Iwata logo and NEO for Iwata are registered trademarks of ANEST IWATA Corporation. All other trademarks are the properties of their respective owners. - Page 12 w w w . I W A T A - A I R B R U S H . c o m Rev2 9/16...
Need help?
Do you have a question about the IS-875HT and is the answer not in the manual?
Questions and answers