Central Machinery 61750 Owner's Manual & Safety Instructions

Central Machinery 61750 Owner's Manual & Safety Instructions

Combination sander 6 inch belt & 9 inch dick

Advertisement

Advertisement

Table of Contents
loading

Summary of Contents for Central Machinery 61750

  • Page 2: Product Specifications

    Indicates a hazardous situation which, if not avoided, could result in death or serious injury. Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. Addresses practices not related to personal injury. For technical questions, please call 1-888-866-5797. Item 61750 Page 2...
  • Page 3: Important Safety Information

    NOT safety glasses. 12. SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool. For technical questions, please call 1-888-866-5797. Item 61750 Page 3...
  • Page 4: Direction Of Feed

    5. Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug. 6. Repair or replace damaged or worn cord immediately. For technical questions, please call 1-888-866-5797. Item 61750 Page 4...
  • Page 5 16. Avoid unintentional starting. Prepare to begin work before 8. DO NOT OPERATE WITH ANY turning on the tool. GUARD DISABLED, DAMAGED, OR REMOVED. Moving guards must move freely and close instantly. For technical questions, please call 1-888-866-5797. Item 61750 Page 5...
  • Page 6: Vibration Safety

    If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. SAVE THESE INSTRUCTIONS. For technical questions, please call 1-888-866-5797. Item 61750 Page 6...
  • Page 7: Product Features

    Washers (83), and two Nuts (84). (See Figure C.) Repeat Steps #1, #2, and #3 to connect the other end of the Frame to the remaining Stand. (See Figure C.) For technical questions, please call 1-888-866-5797. Item 61750 Page 7...
  • Page 8 Bolts (86), with four Washers (87), upward through the Stand’s four mounting holes. Then, firmly tighten the four Bolts into the four threaded mounting holes on the Base. (See Figure D.) For technical questions, please call 1-888-866-5797. Item 61750 Page 8...
  • Page 9 Pulley. Be sure the key stays in the correct position, all the way through the pulley. Repeat steps 3 and 4, putting the Motor Pulley (26) on the lower shaft. (See Figure F.) For technical questions, please call 1-888-866-5797. Item 61750 Page 9...
  • Page 10 Screw (67). Tighten the Set Screw (50) on the Table Support Bracket. Set the Table Support Bracket as shown in Figure J, page 12. Tighten the two Set Screws (97) on the side of the Base to secure the bar. For technical questions, please call 1-888-866-5797. Item 61750 Page 10...
  • Page 11: Sanding Belt

    Figure H. WORK STOP (105) Sand in this area. LOCK KNOB & ADJUST NUT ASSY. (107) SANDING BELT FRAME KNOB (107) SANDING BELT (1) (106) ADJUST NUT (108) FIGURE H For technical questions, please call 1-888-866-5797. Item 61750 Page 11...
  • Page 12: Sanding Disc

    Work Table is shown on the Angle Gauge. (See Figure J.) Once the desired angle of the Work Table (41) is obtained, retighten the Knob (45). (See Figure J.) For technical questions, please call 1-888-866-5797. Item 61750 Page 12...
  • Page 13 Once the desired angle of the Miter Gauge (39) is obtained, retighten the Miter Gauge Knob. (See Figure K.) MITER GAUGE (39) MITER GAUGE KNOB (38) ANGLE SCALE FIGURE K For technical questions, please call 1-888-866-5797. Item 61750 Page 13...
  • Page 14 NOTE: When repositioning the Work Table (41), make sure there is more than " clearance but less than " clearance between the Table and the Sanding Belt Frame (106). (See Figure M.) For technical questions, please call 1-888-866-5797. Item 61750 Page 14...
  • Page 15: End View

    Once the sanding procedure is completed, remove the workpiece from the Sanding Belt (1), turn the Power Switch (64) to its “OFF” position, and unplug the Power Cord (59) from its electrical outlet. (See Figure B.) For technical questions, please call 1-888-866-5797. Item 61750 Page 15...
  • Page 16 Once the sanding procedure is completed, remove the workpiece from the Sanding Belt (1), turn the Power Switch (64) to its “OFF” position, and unplug the Power Cord (59) from its electrical outlet. (See Figure B.) REV 14d For technical questions, please call 1-888-866-5797. Item 61750 Page 16...
  • Page 17: Inspection, Maintenance, And Cleaning

    ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. For technical questions, please call 1-888-866-5797. Item 61750 Page 17...
  • Page 18: Parts List

    6 x 12mm Screw 114 Adjusting Bar 4mm Flat Washer Side Stand 115 Idler Drum 4mm Lock Washer Support 4 x 5 mm Pan 6 x 12mm Screw Head Screw For technical questions, please call 1-888-866-5797. Item 61750 Page 18...
  • Page 19: Assembly Diagram

    Note: If product has no serial number, record Note: Some parts are listed and shown month and year of purchase instead. for illustration purposes only, and are not available individually as replacement parts. For technical questions, please call 1-888-866-5797. Item 61750 Page 19...
  • Page 20 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance.

Table of Contents