Mini cat5 vga transmitter with local port (16 pages)
Summary of Contents for Black Box VX-1002-TX
Page 1
VX-1002-TX VX1000 Series Wallplate Transmitter—HDMI, VGA Extend an HDMI or VGA signal up to 328 feet (100 meters) over a single CATx cable. • Wallplate transmitter design makes installation simple. • Requires a compatible receiver at the other end of the link.
Page 2
FCC and IC RFI Statements/NOM Statement FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufac- turer’s instructions, may cause inter ference to radio communication.
Page 3
NOM Statement 5. El aparato eléctrico no deberá ser usado cerca del agua — por ejemplo, cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca, etc. 6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales que sean recomendados por el fabricante.
Page 4
NOM Statement 17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean derramados sobre la cubierta u orificios de ventilación. 18. Servicio por personal calificado deberá ser provisto cuando: A: El cable de poder o el contacto ha sido dañado; u B: Objectos han caído o líquido ha sido derramado dentro del aparato;...
10. Refer all servicing to qualified service personnel. Disclaimer Black Box Network Services shall not be liable for damages of any kind, includ- ing, but not limited to, punitive, consequential or cost of cover damages, result- ing from any errors in the product information or specifications set forth in this document and Black Box Network Services may revise this document at any time without notice.
Chapter 1: Specifications 1. Specifications Wallplate Transmitter (VX-1002-TX) Video Input (1) HDMI IN, (1) VGA IN, (1) Audio IN Input Signal Type HDMI 1.4 w/HDCP Resolution VGA: 1920 x 1200, 1920 x 1080, 1680 x 1050, Support 1600 x 1200, 1600 x 900, 1400 x 1050, 1440 x 900,...
Page 8
Chapter 1: Specifications Wallplate Transmitter (continued) Audio Input (1) 3.5-mm mini jack, stereo audio binding with VGA input Supported Audio HDMI: Stereo, LPCM 5.1 LPCM 7.1, Dolby True HD, Format DTS-HD Master Audio; VGA: Stereo General Environment Operating 32 to 113° F (0 to 45° C) Temperature Storage -4 to +158°...
Page 9
Chapter 1: Specifications Cable Specifications Cable Type Range Supported Video CAT5e/6 328 ft. (100 m) Up to 1080p @ 60 Hz, 36-bit 230 ft. (70 m) 3840 x 2160 @ 30 Hz, 4:4:4 bit CAT6a/7 328 ft. (100 m) 1080p @ 60 Hz, 48-bit; 1080p @ 60 Hz, 3D;...
2. Overview 2.1 Introduction The VX1000 Series Wallplate Transmitter - HDMI, VGA (VX-1002-TX) is a 2-to-1 wallplate HDBaseT transmitter with one HDMI input, one VGA input, and one HDBaseT output. It enables transmission of an HDMI signal over a single...
Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support at 877-877-2269 or info@blackbox.com. • VX1000 Series Wallplate Transmitter - HDMI, VGA (VX-1002-TX) • (1) 3.81-mm Phoenix male connector (9-pin) • (1) cover with four screws •...
Chapter 2: Overview 2.4 Hardware Description Figures 2-1 and 2-2 illustrate the front and back panels of the transmitter. Table 2-1 describes its components. 4 5 6 7 Figure 2-1. Transmitter front panel. 14 15 16 Figure 2-2. Transmitter back panel. 877-877-2269 | blackbox.com Page 12...
Page 13
Chapter 2: Overview Table 2-1. Transmitter components. Number Component Description VGA IN Connects to VGA source device. Audio Audio input (for use with VGA source) HDMI IN Connects to HDMI source device. HDMI LED ON: HDMI signal transmitted. OFF: No HDMI signal transmitted or unstable. VGA LED ON: VGA signal transmitted.
Chapter 3: Automatic Input Detection 3. Automatic Input Detection • If the current signal is VGA input, the transmitter will not automatically switch to HDMI input. • The button switch will recognize the VGA and HDMI input signals only if they are both valid.
Page 15
Chapter 3: Automatic Input Detection Table 3-3. After power on, change the input signal state. Current Input HDMI IN VGA IN Input Select HDMI IN No—>Yes/ HDMI IN Yes—>No HDMI IN No—>Yes VGA IN HDMI IN Yes—>No HDMI IN HDMI IN Yes—>No VGA IN VGA IN...
Chapter 4: EDiD Presets 4. EDID Presets For VGA input, see the next table. Table 4-1. Set EDID DIP switch for VGA input. DIP Switch Setting VGA Input 1 = OFF (DOWN) Select 1280 x 800 as native video 2 = OFF (DOWN) 3 = OFF (DOWN) 1 = OFF (DOWN) Select 1920 x 1200 as native video.
3. Connect an HDMI display device (LED/LCD display or projector) to the HDMI OUT port on the HDBaseT receiver. 4. Connect the IR emitter cable to the IR OUT port of the VX-1002-TX, connect the IR receiver cable to the IR RX port of the receiver, and connect the IR emitter to the IR TX port of the receiver.
If you encounter any technical difficulties when installing and configuring the matrix, refer to the following troubleshooting checklist. If you cannot resolve your problem, contact Black Box Technical Support at 877-877-2269 or info@blackbox.com. Problem: No picture or poor-quality picture.
Page 19
Chapter 6: Troubleshooting 8. Is the cable wired to 568B standard? Is the cable wired and terminated correctly and are those terminations connected to the correct ports? Incorrect wiring and termination will result in unstable operation or a blank screen. 9.
Page 20
Chapter 6: Troubleshooting Problem: No sound or poor-quality audio. Possible Solutions: Audio is transmitted within the video signal—there is no separate audio track— so a problem with sound will be accompanied by a problem with picture. But you might have technical issues with audio caused by problems communicating between sources, displays, and/or AV receiver settings.