Installation - Viking E-35 Product Manual

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC
outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.
Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent condensation from accumulating
inside the E-35 always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4" diameter hole in the bottom of the gray plastic box..
(2) Standard flat head dry wall
(sheet rock) screws (not included)
*Plastic Rough-In
Box (included)
|
Important: The E-35 will NOT mount
OR
to a standard double gang box.
|
5.22"
5.14"
Optional VE-5x5 Surface
Mount Box (not included)
2.25"
A. Wiring the E-35 Phone Board
Optional C-2000B Advanced Door
Entry Controller, DOD# 156
(not included)
VIKING
MODEL C-2000B
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
1 2 3 4 5 6 7 8 9 1 0 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
J7- J8- J9- J10- J11-
1 1
1 2 3 2 3 2 3 1 2 3 1 2 3
LED1 LED2
LED3 C LED4 C LED5 C LED6 C LED7 C
C C
* Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a TBB-1B Talk Battery Booster may be
required, see DOD# 632 for more information.
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off bare wire ends prior to terminating.
*** Note: To increase surge protection, loosen the PCB mounting screw labeled
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)

Installation

2.1"
4.0"
Wire
knock out
(4) 0.38" diameter
3.25"
(for gooseneck
pedestal mounting)
(1) 0.74"
diameter
Condensation
Drain Hole
Rear View of VE-5x5
(not included)
Optional C-200 or C-250 Basic
Single Entry Phone Interface,
DOD# 169 or 172 (not included)
VIKING
© MODEL C-500
VIKING
ELECTRONICS
HUDSON, WI 54016
* C.O. Line
ADVANCED 2 DOOR ENTRY PHONE
CONTROLLER WITH CALL FORWARDING
or Analog
PABX/KSU
Station
+
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
or
Peel paper liner and
adhere gasket to back of
panel, centering over
mounting holes.
Caution: For rough
surfaces (ie: brick, stucco,
etc.) additional caulking
may be required.
5.0"
Typical
(2) 0.2 x 0.43 slots for
single gang box
(4) 0.2 x 0.43 slots for
double gang box
The optional VE-5x5 Surface Mount Box (left) is
designed to be surface mounted to a single gang
box, double gang box or VE-GNP Gooseneck
3.0" 3.3"
Pedestal (shown right). For more information on
the VE-5x5 and VE-GNP, see DOD# 424.
3.0"
* Note: The plastic rough-in box (part # 259576)
may be purchased separately in advance. Go to
www.vikingelectronics.com and click "Spare Parts".
Wiring
Rear View of
the E-35
** Gel-Filled
Butt Connectors
Red (Ring)
or
Green (Tip)
(as shown above) and fasten a wire with spade terminal (included)
3
Model E-35-EWP shown
in an optional VE-5x5
Surface Mount Box
mounted to a VE-GNP
Gooseneck Pedestal
Other pedestal options
available, see DOD# 424
5.0"
3.63"
ON ON
1 1 2 2
3.63"
ON
1 2 3
5.0"
Ring
Terminal
(included)
*** Earth
Ground
(optional)