Subscribe to Our Youtube Channel
Related Manuals for TESTO Testostor 171
Summary of Contents for TESTO Testostor 171
- Page 1 testostor 1 1 7 7 1 1 Data logger and software module Instruction Manual and Software Description...
-
Page 2: Table Of Contents
PENING THE PROGRAM Humidity calibration ..........17 .............29 TART Adjustment ............. 19 Warranty...............30 Changing batteries - Battery life ......20 Ordering data...............31 Description of the “Testo 171 V.3.1” dialog box and S ......22 OGGER TYPE ERIAL NUMBER testo worldwide ............22 AIN INFORMATION ..........23... -
Page 3: Description
Safety information Description - The testostor 171-1, 171-2, 1722, 171-3, 171-4 and The data loggers from the testostor 171 series measure 171-6 logger housings come under protection class IP and save up to 55,000 readings with a battery life 65, the testostor 171-0 logger housing comes under... -
Page 4: Connection Instructions
The testostor 171 software module can only be operated together with Testo Comfort software. The enclosed instrument driver sets up communication between the testostor 171 series and your PC. -
Page 5: Technical Data
Technical data Technical data testostor 171 data logger series testostor 171 data logger series testostor type: testostor, type: Temperature: Measuring rate: Measuring sensor: 2 s to 24 h (freely selectable) Measuring range Memory capacity: -35 to +70 °C 20,000 readings -35 to +70 °C... - Page 6 ±0.2 °C Alarm output in testostor 1722 The relay switches if the programmed limit values are exceeded or not reached. Pin The following applies if you use a non-Testo plug: assignment in the Lemo socket: 11 mm Limit value not exceeded...
-
Page 7: Requirements
- Windows 2000 or newer (if compatible). system and its workings. • CD Rom drive • Pentium 100 MHz Activate the instrument driver for the testostor 171 data • 32 MB RAM logger series in INSTRUMENT / “NEW DEVICE” and • 15 MB hard disk click on the “Next”... - Page 8 Activate the instrument driver by clicking with the right Activate the instrument driver by clicking with the right mouse button on the testostor 171 icon and select mouse key on the testostor 171 icon and select OPEN. INSTRUMENT SELECTION. If communication between the PC and the data...
-
Page 9: Error Messages
On the job... Error messages Humidity calibration Error message Cause Remedy The humidity sensors in the testostor 171 series (Type • The last command was Communication fault Check connection cable and 171-2/1722/171-3 with integrated Testo humidity sensor not processed try again. -
Page 10: Adjustment
On the job... On the job... Humidity calibration Adjustment External humidity probes (connected to socket 1) should be configured in the P The second window (activate by setting the button to ROBE CONFIGURATION mask prior to calibration Adjustment) in H is not an UMIDITY CALIBRATION alternative for adjustment. -
Page 11: Changing Batteries - Battery Life
Battery life To protect the lithium battery, the maximum permissible storage and transport The testostor 171 series is equipped with long-life Li temperature in the instruments is + 85 °C. batteries which guarantee operation for several years. Battery life is reduced by above-average PC If your measurement program exceeds the remaining communication e.g. -
Page 12: Logger Type And Serial Number
Description of the “testostor 171 V1.” dialog box Description of the “testostor 171 V1.” dialog box Once the data logger has been set up in INSTRUMENT, ROBE CONFIGURATION NEW DEVICE, open the menu for the instrument icon Carry out the probe configuration shown in the table. -
Page 13: Name
TART window. Measuring rate, are shown here. Battery life The testostor 171 series is equipped with long-life Li batteries which guarantee operation for up to several years. Battery life is reduced by an above-average PC communication e.g. by extended online measurements. -
Page 14: Read Out Memory
Description of the “testostor 171 V1.” dialog box Description of the “testostor 171 V1.” dialog box OK/C ANCEL NLINE MEASUREMENT You can OK confirms your inputs while Cancel discards your - install the logger with an attached display module and input. -
Page 15: Ate And Ime
Description of the “testostor 171 V1.” dialog box Description of the “testostor 171 V1.” dialog box The D and T are adapted to the date and time of ASSWORD your PC via the Synchronisation button. You can create a password, which will be saved in the logger, via this button. -
Page 16: Warranty
Ordering data Warranty from Testo Dear Customer Data logger incl. battery and magnet with internal external Thank you for your confidence in Testo which you have testostor 171-0 °C 0577.1719 shown by buying this measuring instrument. You have testostor 171-1 °C °... -
Page 17: Testo Worldwide
Fax (33) 44 40 00 Tel. (2) 57 29 02 05 Fax 237 17 48 Fax (2) 33 14 34 DKD calibration certificate (for testostor 171-1, 171-4, 171-6) Fax (2) 57 29 04 10 testo@testo.hu farmahem@mt.net.mk (Measuring points, freely selectable in the range from -40 to +120 °C) 0520.0201... - Page 18 Fax (1) 58 49 20 testline@customers.digiro.net afri.sta@gnet.tn SINGAPORE / MALAYSIA / TURKEY INDONESIA Testo Elektronik ve Test Ölcüm Futron Electronics PTE LTD Cihazlari Dis Ticaret Ltd. STi Singapore 329 714 80280 Esentepe-Istanbul Tel. (65) 62 50 24 56 Tel. (212) 2 75 77 99...
- Page 19 Testo AG Postfach 11 40, D-79849 Lenzkirch Testo-Straße 1, D-79853 Lenzkirch Tel. (0 76 53) 6 81 - 0 (0 76 53) 6 81 - 1 00 E-Mail: info@testo.de http://www.testo.de 0971.2530/T/Ni/PC_qxd/08.02...
Need help?
Do you have a question about the Testostor 171 and is the answer not in the manual?
Questions and answers