Factors Influencing Vaporization; The Crafty Vaporizer - Storz & Bickel GMBH Crafty Instructions For Use Manual

5 . FA C T O R S I N F L U E N C I N G VA P O R I Z AT I O N
The amount of aromas and fragrances
released can be influenced by the fol-
lowing factors:
1. Quality: The amount of aroma or
fragrance contained in the respec-
tive plant material that can be va-
porized.
2. Quantity: The amount of vaporiza-
tion material in the Filling Cham-
ber.
3. Surface: The finer the plant is
ground, the greater the surface
and the more aromas and fra-
grances can be released during
the vaporization cycle.
4. Temperature: The higher the tem-
peratures, the more aromas and
fragrances will be released at
once.
6 . T H E C R A F T Y VA P O R I Z E R
Unpacking
The box contains all components as
well as the Instructions for Use. Keep
the Instructions for Use for future ref-
erence.
Remove the Vaporizer and the ac-
cessories from the box. Immediately
after unpacking, check whether the
Vaporizer, the accessories, the power
adapter and the device plug are all in-
cluded in the delivery and work prop-
erly. If you notice any defects, inform
the seller or the delivery agent imme-
diately.
Please note: Increasing the tempera-
ture should be the last resort, because
plant material tastes more roasted
when using higher temperature.
Since the plant ingredients are re-
leased in a gentle manner, the vapori-
zation cycle may be repeated with the
same contents in the Filling Chamber.
Depending on the four factors de-
scribed above, the Filling Chamber
contents may be reused multiple
times until the aromas and fragrances
are released completely.
If no more vapor is produced at the
highest temperature, then the vapori-
zation material is completely exhaust-
ed and must be replaced with new
material. However, for the best aroma
results it is advisable to replace the
vaporization material before
point.
The packing material (plastic
bags, boxes etc.) must be
kept out of the reach of chil-
dren as it is a potential source of dan-
ger.
Please dispose of the packing mate-
rial in a proper and environmentally
friendly manner.
We recommend keeping the original
packaging in case it is required later
(transport, Storz & Bickel Service
Center etc.).
12
Power Connection
Before connecting up the Vaporizer,
make sure that the information given
on the power adapter type label cor-
responds to the local power supply
voltage.
All parts of the electrical system must
comply with currently applicable offi-
cial regulations.
Place the heated Vaporizer only on a
hard, stable surface, and not on any
soft or heat-sensitive material.
Take care that the power adapter USB
cable cannot be damaged through
kinking, crushing or pulling.
Improper
lead to personal injury or ma-
terial damages, for which the
this manufacturer cannot be held respon-
sible.
Application and Operation
This Vaporizer was developed
for vaporizing the plant mate-
rials listed in the plant over-
view. Any other use is inappropriate
and potentially dangerous.
The user should always follow the
instructions listed here for use and
maintenance.
If you have any concerns, or if there
are any problems immediately switch
off the Vaporizer and pull the power
adapter cord, if used, from the sock-
et. Do not try to remedy the defect
6 . T H E C R A F T Y VA P O R I Z E R
yourself. Contact our Service Center
directly.
After using the Vaporizer and power
adapter, allow them to cool down be-
fore placing them in storage.
Storage
Store the Vaporizer and the power
adapter in a dry place protected
against the effects of weather and out
of the reach of children or unqualified
persons.
In Case of Problems
If the power adapter has been in use,
unplug it at the socket and ensure that
installation may
no one can connect the Vaporizer to
the mains supply again without this
being noticed.
Before any maintenance work is done,
the Vaporizer has to be switched off
and the power adapter unplugged
from the power supply.
Put the Vaporizer in the original pack-
aging, or pack it properly in other pack-
ing material, and send it to our Service
Center.
13