Table of Contents
Advertisement
5 . FA C T O R S I N F L U E N C I N G VA P O R I Z AT I O N
The amount of aromas and fragrances
released can be influenced by the fol-
lowing factors:
1. Quality: The amount of aroma or
fragrance contained in the respec-
tive plant material that can be va-
porized.
2. Quantity: The amount of vaporiza-
tion material in the Filling Cham-
ber.
3. Surface: The finer the plant is
ground, the greater the surface
and the more aromas and fra-
grances can be released during
the vaporization cycle.
4. Temperature: The higher the tem-
peratures, the more aromas and
fragrances will be released at
once.
6 . T H E H O T A I R G E N E R AT O R PLENTY
Unpacking
The box contains all components as
well as the Instructions for Use. Keep
the Instructions for Use for future ref-
erence.
Remove the Hot Air Generator and
the accessories from the box. Imme-
diately after unpacking, check wheth-
er the Hot Air Generator, the acces-
sories, the power cord and the power
plug are all included in the delivery
and work properly. If you notice any
defects, inform the seller or the deliv-
ery agent immediately.
Please note: Increasing the tempera-
ture should be the last resort, because
plant material tastes more roasted
when using higher temperature.
Since the plant ingredients are re-
leased in a gentle manner, the vapori-
zation cycle may be repeated with the
same contents in the Filling Chamber.
Depending on the four factors de-
scribed above, the Filling Chamber
contents may be reused multiple times
until the aromas and fragrances are
released completely.
If no more vapor is produced at the
highest temperature, then the vapori-
zation material is completely exhaust-
ed and must be replaced with new
material. However, for the best aroma
results it is advisable to replace the
vaporization material before this point.
The packing material (plas-
tic bags, styrofoam materi-
al, boxes etc.) must be kept
out of the reach of children as it is a
potential source of danger.
Please dispose of the packing ma-
terial in a proper and environmen-
tally friendly manner.
We recommend keeping the origi-
nal packaging in case it is required
later (transport, Storz & Bickel Ser-
vice Center etc.).
12
6 . T H E H O T A I R G E N E R AT O R PLENTY
Power Connection
Before connecting up the Hot Air
Generator, make sure that the infor-
mation given on the device's type la-
bel corresponds to the local power
supply voltage.
All parts of the electrical system must
comply with currently applicable offi-
cial regulations.
It is mandatory to electrically ground
the Hot Air Generator. The manufac-
turer will not bear any responsibility
whatsoever if this accident preven-
tion measure is not taken.
Place the heated Vaporizer only on a
hard, stable surface, and not on any
soft or heat-sensitive material.
Take care that the power cord cannot
be damaged through kinking, crush-
ing or pulling.
Improper
installation
may
lead to personal injury or ma-
terial damages, for which the
manufacturer cannot be held respon-
sible.
Application and Operation
This Vaporizer was devel-
oped for vaporizing the plant
materials listed in the plant
overview. Any other use is inappropri-
ate and potentially dangerous.
The user should always follow the in-
structions listed here for use and
maintenance; the device should only
be used in a sitting position.
If you have any concerns, or if there
are any problems immediately switch
off the Hot Air Generator and pull out
the power plug from the socket. Do
not try to remedy the defect yourself.
Contact our Service Center directly.
After using the device, allow it to cool
down before placing it in storage.
Storage
Store the Hot Air Generator in a dry
place protected against the effects
of weather and out of the reach of
children or unqualified persons.
In Case of Problems
Immediately unplug the power cord
and ensure that no one can connect
the Hot Air Generator to the mains
supply again without this being no-
ticed.
Before any maintenance work is done,
the device has to be switched off and
the power plug unplugged from the
power supply.
Put the Hot Air Generator in the origi-
nal packaging, or pack it properly in
other packing material, and send it to
our Service Center.
Troubleshooting
Please make sure that the current is
on and that the fuse (in the mains fuse
box) is switched on and is not defec-
tive.
13
Advertisement
Table of Contents
