Auto Sense; Infrared Learning; Automatic Software Download - NAD C 338 Owner's Manual

OPERATION
USING THE C 338
Network Mode
• If there is no user interface interaction and no active source input
within 20 minutes, the unit switches to standby mode at reduced
system performance level (less than 2W).
•
Network and Bluetooth connections are maintained at network
standby mode.
•
At network standby mode, the C 338 can be switched back to
operating mode using any of the following methods.
- Activate or play network connected App
-
Play paired Bluetooth source
- Rotate VOLUME knob or press AMP 3 remote control's VOLUME
d/f buttons
- Press any of the a SOURCE s or BASS EQ buttons
-
Press front panel Standby button or AMP 3 remote control's [ON]
button

AUTO SENSE

Auto sense feature enables the C 338 to wake up from standby mode
when triggered by an active (digital/analog) audio source input.
Enable/Disable Auto Sense mode
While in operating mode, press and hold BASS EQ button until "A" (On) is
shown in the front panel display.
Repeat the same to disable Auto Sense mode but this time the display
should show "-" (Off ).
A (On): Unit wakes up from standby mode when triggered by active audio
source input.
- (Off): Unit remains at standby mode even if it is triggered by active audio
source input.
IMPORTANT NOTES
With Auto Sense mode set to "On", the unit cannot go to standby
mode as long as there is an active audio source input. Undertake the
following to enable the unit to go to standby mode with Auto Sense set
to "A" (On).
• Shut down or pause your audio source input(s)
• Set Auto Sense setting to "-" (Off)

INFRARED LEARNING

Infrared (IR) Learning enables any non-NAD remote control learn IR remote
control codes. With the learned codes, the configured non-NAD remote
control can be used to command or operate the C 338. The IR remote
control codes are based from the supplied AMP 3 remote control.
HOW TO LEARN IR REMOTE CONTROL CODES
1 Press and hold at the same time front panel BASS EQ and a SOURCE
buttons until "F1" appears on the front panel display. The display of "F1"
indicates that the unit is at IR learning mode.
2 A total of twelve IR remote control codes can be learned. These codes
are defined as "F1, F2....F12" and are identified by their allocation in the
AMP3 remote control layout below.
F1 F2
F3 F4 F5
F6 F7
➜
F8 BASS F9
DIM
F10 F11 F12
AMP 3
14
3 Use front panel a SOURCE or SOURCE s to toggle through F1, F2...F12.
4 For example, to learn "F5" (Volume Up), toggle a SOURCE or SOURCE s
5 Press BASS EQ and "F5" will begin to flash.
6 While pointing the non-NAD remote control to the front panel display,
7 Repeat the same process above to learn other IR remote control codes.
8 To save the learned IR remote control codes and at the same time exit IR

AUTOMATIC SOFTWARE DOWNLOAD

Upon powering up and configuring the Wi-Fi connection of your C 338,
it will begin an installation process to ensure it has the newest device
software. Do not interrupt the power supply or enter new commands
during this installation process.
The display will initially show in percentage the progress of software
download.
The C 338 will then get automatically updated with the downloaded
software. The update progress is indicated in the display as progressive
"-" (dash) marks. When the display appears like the image below, the
process is completed and the unit will automatically restart.
NOTE
BASS
DIM
AMP 3
until "F5" is shown in the front panel display.
press the corresponding button on the non-NAD remote control where
"F5" will be learned. "F5" will stop flashing, briefly stay solid and then the
next command (F6) is displayed. The solid "F5" indicates that "F5" code is
already learned by the non-NAD remote control.
learning mode, press and hold the front panel BASS EQ and a SOURCE
buttons until the front panel display reverts to volume level display.
This installation process is initiated periodically to keep C 338 updated
with the latest software.