Eiki EIP-HDT30 Service Manual page 50

Electrical Adjustment
Grp / No. Item
22 Measured Blue - Luma
30 Measured Cyan - X
31 Measured Cyan - Y
32 Measured Cyan - Luma
40 Measured Magenta - X
41 Measured Magenta - Y
42 Measured Magenta - Luma
50 Measured Yellow - X
51 Measured Yellow - Y
52 Measured Yellow - Luma
60 Measured Half White - X
61 Measured Half White - Y
62 Measured Half White - Luma
70 Measured Full White - X
71 Measured Full White - Y
72 Measured Full White - Luma
100 Measured Data Update
160 VIDI
0 Brightness (Wheel)-Dynamic
1 Brightness (Wheel)-Not Dynamic Brightness Wheel (Color)
2 Color (Wheel)-Dynamic
3 Color (Wheel)-Not Dynamic
161 Lamp Sync
0 Brightness (Wheel)-x2 Mode
1 Brightness (Wheel)-x3 Mode
2 Color (Wheel)-x2 Mode
3 Color (Wheel)-x3 Mode
200 Option
0 Logo Display Prohibition
1 RS232C Baud rate
4 CABLE SW
5 PW Debug Command Enable
6 Device Refresh Disable
11 HDCP EDID Data Setting
15 Lens Shift Centering Setting *
21 Lamp Warning Time (NORMAL)
22 Lamp Warning Time (ECO)
23 Lamp Warning Time (HIGH)
24 Projector Time REset Times
50 Lamp Replacement Display
51 Filter Warning Display
53 Filter Counter Reset Times
54 Factory Default Executed Times
55 Motor Stop
56 Menu Position (X)
57 Menu Position (Y)
58 Lamp Go Out
59 LENS LOCK Warning Display
62 Color Wheel Warning
65 Peltier PWM Enable
66 Peltier PWM High Term
67 Peltier PWM Low Term
70 ADC Device Select for Analog PC 0 = ISL51002, 1 = PW392 AFE
71 ADC Device Select for Component 0 = ISL51002, 1 = PW392 AFE
72 Component/RGB Auto Switch
80 Destination
100 Disable Auto Picture Control
140 Offset Add Setting Status
141 Offset Add Setting Change
142 Offset Value
143 Offset Add Execute Times
144 Offset Add Cancel Times
201 Option (Signal)
0 FrameLock Option
Function
Execute the update when the value is set to 10.
Brightness Wheel (Brightness)
Brightness Wheel (Brightness)
Brightness Wheel (Color)
0:Menu 1:Forced
0: 19200bps 1: 9600bps
Long Cable 0: Disable 1: Enable
0: Disable (Serial Command Enable)
1: Enable (PW Debug Mode)
0: Enable 1: Disable
0: DVI EDID Data, 1: HDCP EDID Data
Reset Centering position when the value is set to 10.
1:On 0:Off
1:On 0:Off
Read only
Read only
Motor Operation 0: Enable 1: Disable
X Offset
Y Offset
Lamp goes out
0: Enable 1: Disable
0: Enable 1: Disable
Peltier Drive PWM 0: Auto, 1: Manual, 2: Disable
0: Disable 1: Enable
Language Set at Shipping 0:English 1:Japanese
0 : Normal operation 1 : Auto Picture Control Off
0: Not use Offset Add, 1: Use Offset Add (Read only)
Change the Offset Add Setting when the value is set to 10.
Offset Add Value at Shutdwon Temp(Read only)
(Read only)
(Read only)
Frame Lock Setting 1: Normal(PC) 0: OFF
Range
0 - 32767
0 - 1000
0 - 1000
0 - 32767
0 - 1000
0 - 1000
0 - 32767
0 - 1000
0 - 1000
0 - 32767
0 - 1000
0 - 1000
0 - 32767
0 - 1000
0 - 1000
0 - 32767
0 - 10
0 - 10
0 - 10
0 - 10
0 - 10
0 - 65535
0 - 65535
0 - 65535
0 - 65535
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 1
0 - 10
1-16
1-16
1-16
0 - 255
0 - 1
0 - 1
0 - 255
0 - 255
0 - 1
0 - 1024
0 - 1024
0 - 1
0 - 1
0 - 1
0 - 2
0 - 600
0 - 600
0 - 1
0 - 1
0 - 1
0 - 1
0-1
-
0 - 10
-
0 - 255
0 - 255
0 - 1
-50-
Initial Note
405/184/323/347
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
0/0/0/0
310/315/0/0
335/336/0/0
3953/2948/0/0
315/320/307/307
343/350/336/340
11860/7462/10160/11420
-
4
2
5
3
1130
900
429
352
0
0
0
0
0
1
0
4
6
4
0
1
1
0
0
0
0
0
0
0
0
0
600
600
0
0
1
0
Initial: 1 Shipping 0
0
0
0
0
0
1