Pioneer PDP-6071PU Service Manual
  1. Manuals
  2. Brands
  3. Pioneer Manuals
  4. Monitor
  5. PDP-6071PU
  6. Service manual

Pioneer PDP-6071PU Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

PLASMA DISPLAY SYSTEM
PDP-6071PU
PDP-6070PU
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
Model
Type
PDP-6071PU
KUC
PDP-6071PU
KUCXC
PDP-6070PU
KUC
PDP-6070PU
KUCXC
This service manual should be used together with the following manual(s).
Model No.
PDP-6071PU, PDP-6070PU
For details, refer to "Important Check Points for good servicing".
PIONEER CORPORATION
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2006
POWER
ON
STANDBY
REC TIMER
Power Requirement
AC 120 V
AC 120 V
AC 120 V
AC 120 V
Order No.
ARP3395
SCHEMATIC DIAGRAM, PCB CONNECTION DIAGRAM
4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PDP-6071PU
Remarks
ORDER NO.
ARP3394
Remarks
T-IZV SEPT. 2006 printed in Japan

Advertisement

Table of Contents
loading

Related Manuals for Pioneer PDP-6071PU

Summary of Contents for Pioneer PDP-6071PU

  • Page 1 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2006 T-IZV SEPT.

  • Page 2: Notes On Service Visit

    Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-6071PU...
  • Page 3 PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
  • Page 4 Charged Section. 607 SCAN B Assy 60 Y DRIVE Assy POWER SUPPLY Unit 60 X DRIVE Assy Conductive plate X 607 SCAN A Assy AC inlet Power switch (S1) Fig. High Voltage Generating Point (Rear view) PDP-6071PU...
  • Page 5 To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-6071PU...

  • Page 6: Quick Reference Upon Service Visit

    "OFF" to "ANA AD YCBCR". 3. You can change Mask patterns by pressing [«] to select {SG PATTERN} then using [|] or [\]. Note: When you switch "SG MODE" routes, some displays become monochrome, as they are in Y-signal only mode. PDP-6071PU...
  • Page 7 2. CMB MASK 01 For use while Combination Mask is displayed. • • • • • Use [»] or [«] to select the type of mask. To "Structure of Layers in Panel Factory Mode 2" 11. CMB MASK 10 PDP-6071PU...

  • Page 8: Table Of Contents

    5.2.1 BLOCK DIAGRAM OF THE POWER-DOWN SIGNAL..............103 5.2.2 POWER DOWN OF FAILURE ANALYSIS ..................104 5.3 SHUT DOWN ............................106 5.3.1 BLOCK DIAGRAM OF THE SHUT-DOWN SIGNAL................ 106 5.3.2 SHUT DOWN OF FAILURE ANALYSIS................... 107 5.4 NON-FAILURE SYMPTOMS........................108 PDP-6071PU...
  • Page 9 10.3 POWER ON/OFF FUNCTION FOR THE LARGE-SIGNAL SYSTEM ..........191 10.4 LED INFORMATION ..........................192 10.5 SPECIFICATION ABOUT THE THERMAL PROTECTION..............193 10.6 PROCESSING IN ABNORMALITY ......................194 10.7 TRAP SW..............................195 11. SPECIFICATIONS ............................196 11.1 MAIN SPECIFICATIONS ........................196 11.2 ACCESSORIES............................197 11.3 PANEL FACILITIES..........................198 12. IC INFORMATION ............................201 PDP-6071PU...

  • Page 10: Exploded Views And Parts List

    (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING SECTION 12, 14, 16, 30 Speed clamp ×3 Noise filter for G-Link cable Binder for noise filter Bead band ×3 PDP-6071PU only PDP-6071PU only PDP-6071PU...
  • Page 11 See Contrast table (2) Cleaning Caution See Contrast table (2) Terminal Position Sheet AAX3330 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description...

  • Page 12: Rear Section

    2.2 REAR SECTION 22 24 MAIN CN7101 MAIN CN4010 TANSHI CN8801 Refer to "2.3 FRONT SECTION". PDP-6071PU...
  • Page 13 Caution Label See Contrast table (2) Terminal Display Label A (U/B) AAX3325 Terminal Display Label B50 (U/B) AAX3414 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No.

  • Page 14: Front Section

    Note : Take care that the size is different between the coil spring ABH1120 at Front Case and ABH1124 at Mechanical Switch Assy. Refer to P16. 18.2 17.5 ABH1120 ABH1124 for Front Case/ for Mechanical Power Button Switch Assy PDP-6071PU...
  • Page 15 FRONT SECTION PARTS LIST Mark No. Description Part No. 42 & 60 LED Assy AWW1134 60 IR Assy AWW1137 Front Case Assy 607 AMB2930 Pioneer Name Plate AAM1109 Coil Spring ABH1120 Blind Cushion AEB1449 Nyron Rivet AEC1671 Power Button AAD4147...

  • Page 16: Chassis Section (1/2)

    -nical Switch Assy and ABH1120 at Front Case . Refer to P14. 18.2 17.5 ABH1120 ABH1124 for Front Case/ for Mechanical Power Button Switch Assy MAIN CN4009 Refer to "2.5 CHASSIS SECTION (2/2)". 49 46 49 31 POWER (*1) PDP-6071PU...
  • Page 17 Wire Saddle AEC1745 Screw ABA1364 Ferrite Core Holder AEC1818 Re-use Wire Saddle AEC1945 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description /KUC /KUCXC...

  • Page 18: Chassis Section (2/2)

    6, 35 6, 35 6, 35 6, 35 6, 35 6, 35 6, 35 S a,b 6, 35 AUDIO CN3752 MAIN MAIN CN4008 CN4002 V a,b Power switch AC inlet T a,b U a,b Refer to "2.6 PANEL CHASSIS SECTION". PDP-6071PU...
  • Page 19 Screw (M3 x 6) ABA1366 10P/5P Housing Wire (J104)(J127) ADX3409 10P/5P Housing Wire (J114)(J128) ADX3410 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description...

  • Page 20: Panel Chassis Section

    2.6 PANEL CHASSIS SECTION PDP-6071PU...
  • Page 21 60 ADDRESS S Assy AWW1189 607 SCAN A Assy AWW1186 607 SCAN B Assy AWW1187 PCB Spacer AEC1372 PCB Spacer AEC1944 PCB Spacer AEC1947 Conductive Plate Holder AMR3446 Address Plate A Assy ANG3036 Address Plate B Assy ANG3037 Screw ABA1367 PDP-6071PU...

  • Page 22: Multibase Section

    2.7 MULTIBASE SECTION 60 DIGITAL CN3001 SIDE KEY CN9501 60 LED CN9801 POWER POWER (side) (Fan) 42 & 60 LED CN9601 POWER POWER SIDE CN9101 PDP-6071PU...
  • Page 23 Binder AEC-093 Locking Card Spacer AEC1429 Screw PMB30P080FNI Wire Saddle AEC1745 (2) CONTRAST TABLE PDP-6071PU/KUC, KUCXC, PDP-6070PU/KUC and KUCXC types are constructed the same except for the following: PDP-6071PU PDP-6071PU PDP-6070PU PDP-6070PU Mark No. Symbol and Description /KUC /KUCXC /KUC...

  • Page 24: Pdp Service Assy 607 (Awu1228)

    Detach it from the product to be repaired and attach it to the Assy for service. ×4 ×2 ×5 ×4 ×5 ×2 ×2 ×2 ×5 ×4 ×5 ×4 ×2 ×4 ×2 ×2 ×4 ×2 ×4 ×7 ×4 ×4 ×5 ×2 ×4 ×2 ×2 (for transport) PDP-6071PU...
  • Page 25 Packing Section ×4, 22, 24 ×4, ×3, ×3, ×8, ×8, ×4 ×21 ×3 ×20 ×2 PDP-6071PU...
  • Page 26 Y Drive Protection Sheet A AMR3640 Gasket MTB ANK1879 Rivet A BEC1158 Caution Label AAX3031 NSP 37 Drive Voltage Label ARW1097 • • • • • Screw (M3 x 6) ABA1366 Screw ABA1367 Screw ABZ30P080FTC Screw AMZ30P060FTB Screw APZ30P100FTB Screw BPZ30P080FTB Screw PMB30P080FTB PDP-6071PU...

  • Page 27: Pcb Parts List

    1730,1740,1750,1760 ACG1137 MISCELLANEOUS 1731,1741,1751,1761 ACG1136 1601 CHIP SOLID INDUCTOR QTL1013 1770,1780 ACG1137 CN 1601 PH CONNECTOR AKM1291 CN 1602 40P CONNECTOR AKM1348 1771,1781 ACG1136 RESISTORS 60 ADDRESS S ASSY 1601–1605 RS1/16SS1000F Other Resistors RS1/16SS###J [60 ADR S LOGIC] SEMICONDUCTORS PDP-6071PU...

  • Page 28: Scan A Assy

    CKSRYB105K6R3 1930,1940,1950,1960 ACG1137 2905–2907,2915–2917 CCSRCH220J50 1931,1941,1951,1961 ACG1136 2908–2910,2918–2920 CCSRCH151J50 1970 ACG1137 2921,2922,2931,2932 ACG1088 1971 ACG1136 2925–2927,2935–2937 CCSRCH220J50 2928–2930,2938–2940 CCSRCH151J50 2941,2942,2951,2952 ACG1088 2943,2953 CKSRYB105K6R3 607 SCAN A ASSY 2945–2947,2955–2957 CCSRCH220J50 SEMICONDUCTORS 2948–2950,2958–2960 CCSRCH151J50 IC 2801–2806 SN755870KPZT-P 2803–2807,2809 1SS302 2810 1SS355 PDP-6071PU...
  • Page 29 4418 2SA1586 4401 1SS355 IC 4108 NJM2846DL3-18 IC 4110 PQ090DNA1ZPH 4402 UDZS30(B) 4101,4110 RN1902 4104 DTC124EUA 4105,4106 UPA1917TE MISCELLANEOUS 4401–4405 BTH1121 4107,4108,4112,4113 2SC4116 4401–4404 VTF1080 4109 2SD2114K 4401,4402 AKX1061 4101–4110 1SS355 > 4401 AXF116 4111,4114,4115 1SS357 > 4402 AXF117 PDP-6071PU...
  • Page 30 IC 5101 UPD64015AGM-UEU 4704 RS1/16S1001F IC 5102 EDS1616AGTA-75-E 4705 RS1/16S2700F 4724,4725 RS1/16S5600F 4728,4731 RS1/16S1800F MISCELLANEOUS 4770,4771 RS1/16S681J 5101–5103 BTX1042 5102 ASS1191 4772,4774,4778,4779 RS1/16S102J 4783,4787,4795,4796 RS1/16S182J 4793,4814,4815 RS1/16S821J RESISTORS 4794,4811,4813 RS1/16S221J 5101–5103,5138 ACN1246 4804,4806,4807,4817 RS1/16S182J 5104,5105 BCN1067 5106-5108 RS1/16S0R0J 4818 RS1/16S182J PDP-6071PU...
  • Page 31 ASS1192 6003 LCTAW1R5J2520 6004 LCYA10NJ2520 6006 LCYAR82J2520 RESISTORS 6001 BTF1130 5401–5403 BCN1071 5415 RS1/10S0R0J 6002–6006 VTF1084 5450 RAB4CQ473J 6007 ATF1219 5451 RAB4CQ100J 6008,6009 VTF1080 > 5452,5455 RAB4CQ103J 6001 AXF116 5454 RAB4CQ470J RESISTORS Other Resistors RS1/16SS###J 6011 RS1/16SS6801F 6023 RS1/16SS2201F PDP-6071PU...
  • Page 32 6110,6112,6114,6121 CKSSYB102K50 MISCELLANEOUS 6111,6113 CCSSCH390J50 6401–6412 VTF1084 6123 CKSSYB102K50 6124–6126 CCSSCH101J50 RESISTORS 6401 RS1/16SS1002F 6402,6404 RS1/16SS1101F [F/E IC BLOCK(U)] 6405–6407,6410–6412 RS1/16SS75R0F SEMICONDUCTORS 6420 RAB4CQ102J IC 6201 BCM3517KQLGB0 6444 BCN1071 6445 BCN1067 MISCELLANEOUS Other Resistors RS1/16SS###J 6201 BTX1042 6202 LCTAW1R8J2520 PDP-6071PU...
  • Page 33 UDZS4R7(B) 7110 RAB4CQ101J 7144,7145,7151,7152 RS1/16SS3302F MISCELLANEOUS 7155,7156,7195,7196 RS1/16SS3302F 6901 LCTAW2R2J2520 Other Resistors RS1/16SS###J 6901-6904 CTF1557 JA 6901 AKN1073 CAPACITORS 6901 BSS1134 CN 6901 BKP1159 7102,7165,7174,7177 DCH1165 7103,7109,7110 DCH1201 RESISTORS 7107,7108 CKSRYB105K10 7111-7114 CCSRCH331J50 6912,6913 RS1/16S3010F 7115,7117,7119,7120 CKSSYB103K16 6952 RAB4CQ472J PDP-6071PU...
  • Page 34 7550,7565 RS1/16SS5602F CAPACITORS 7551,7566 RS1/16SS1202F 7301-7303,7305 CKSSYB102K50 Other Resistors RS1/16SS###J 7304 CCSSCH680J50 7306-7315,7319,7320 CKSSYB104K10 CAPACITORS 7321-7323 CKSSYB102K50 7501,7502 ACH1442 7503 CKSSYB104K10 [POWER_1 BLOCK(U)] 7504,7508,7513 CKSSYB103K16 SEMICONDUCTORS 7506,7507 CKSSYB102K50 IC 7401 NJM2370U09 7509 CKSSYB332K50 IC 7402 NJM2871BF05 IC 7403 MM1563DF PDP-6071PU...
  • Page 35 8312,8313 DCH1201 CAPACITORS 8101 CKSSYB102K50 [MAIN UCOM BLOCK(U)] 8102,8126 DCH1201 SEMICONDUCTORS 8103-8106,8108-8111 CCSSCH221J50 8107,8112-8120 CKSSYB104K10 IC 8401 MB91305PMC-G-BND 8121-8125,8127-8129 CCSSCH221J50 IC 8402 AGC1006 IC 8403 PST3628UR 8134-8147 CKSSYB104K10 IC 8407 PQ200WNA1ZPH IC 8409 BR24L64F-W [MULTI BLOCK(U)] IC 8410,8411 TC74VHC125FTS1 PDP-6071PU...
  • Page 36 VNE1949 CN 8802 AKM1349 CN 8803 AKM1348 RESISTORS All Resistors RS1/16SS###J RESISTORS 8801,8802 RS1/10S151J 8811-8816,8850,8860 RS1/16S75R0F CAPACITORS 8861,8874-8876 RS1/16S75R0F 9105,9106 CKSRYB105K10 8880-8882,8898 RS1/16S75R0F 9114 CKSSYF104Z16 8901 RS1/16S4701F 8911 RS1/16S102J Other Resistors RS1/16SS###J AUDIO ASSY SEMICONDUCTORS CAPACITORS IC 3751 LA4625 PDP-6071PU...
  • Page 37 CN 9801 CONNECTOR AKP1303 3838,3839 CEHAT4R7M50 RESISTORS 9801–9803 RS1/16S0R0J SP TERMINAL ASSY Other Resistors RS1/16SS###J MISCELLANEOUS > 3901,3902 ATF1224 JA 3901 SPEAKER TERMINAL AKE1061 CAPACITORS 9801 CKSSYB102K50 9802 CKSSYF104Z16 RESISTORS 9803 ACG7046 >All Resistors RS1/16S###J All Resistors RS1/16S###J CAPACITORS 3903,3911,3917,3919 CKSRYB682K50 PDP-6071PU...
  • Page 38 AGC1026 Other Resistors RS1/16SS###J IC 3302,3305 PST3628UR IC 3303 SN74AHC08PW IC 3304 PST3610UR CAPACITORS 3301 RN1901 3501–3512,3520–3523 CKSSYB102K50 3302 HN1C01FU [DIGITAL DD CON BLOCK] MISCELLANEOUS MISCELLANEOUS 3302 (102.5 MHz) ASS1188 3601 DD CON UNIT AXY1137 CN 3301 CONNECTOR CKS4835 PDP-6071PU...
  • Page 39 Q 1207 R5009ANJ Q 1251 DTC143EK Q 1252 DTC123TKA CAPACITORS D 1201,1205 UDZS5R6(B) C 1001,1003 CEHAT470M16 D 1202,1203,1206,1210 CRH01 C 1002,1004,1005 CKSRYB104K16 D 1204,1211 1SS355 C 1006,1007 CCSRCH331J50 D 1207 1SS302 D 1208 UDZS5R1(B) D 1209 UDZS16(B) [X RESONANCE BLOCK] PDP-6071PU...
  • Page 40 D 1306,1307,1331 1SS355 D 1321,1322 CRF03 [Y RESONANCE BLOCK] D 1323 U1ZB330 SEMICONDUCTORS D 1332 UDZS6R2(B) D 1333 UDZS12(B) IC 2101,2104 TND307TD IC 2102 PS9117 IC 2103,2151 AXF1159 MISCELLANEOUS IC 2181 BA10393F 2101 2SC2412K T 1301 ATK1162 T 1321 ATK1153 PDP-6071PU...
  • Page 41 IC 2402,2407,2421,2490 TC74AC540FT 2208,2221,2231,2241 UDZS5R6(B) IC 2405,2406,2408,2410 PS9117 2222,2223,2232,2233 CRH01 IC 2481,2482 PST3638UR 2242,2243,2281,2282 CRH01 2251 UDZS5R1(B) 2271 1SS301 MISCELLANEOUS 2272 UDZS16(B) 2401 BTH1136 2283,2289 UDZS9R1(B) 2402,2403 BTH1134 2401,2402 ATX1062 2290 UDZS8R2(B) CN 2401,2402 15P CONNECTOR AKM1200 2351,2380 1SS355 PDP-6071PU...
  • Page 42 CKSRYB104K16 2602,2681,2686 CEHAT101M25 2503 CEHAT470M16 2603,2685 ACG1105 2505,2555 CEHAT101M25 2604 CKSRYB102K50 2506 ACH1450 2605 CEHAT221M10 2508 CEHAT331M16 2606,2607,2653,2684 CKSRYB104K16 2509 CEHAT470M25 2652 ACH1449 2510 ACH1413 2654 CEHAT101M16 2551 ACH1448 2655,2660 CKSRYF104Z50 2552 ACH1451 2656,2657 CEHAT221M35 2554 CEHAT101M16 2658 CKSRYB104K25 PDP-6071PU...

  • Page 43: Power Supply Unit

    Mark No. Description Part No. 2659 CKSRYB105K10 2661 CCG1186 2682 CKSYB105K25 2683 CKSRYB103K50 2687,2688 CKSRYB104K16 POWER SUPPLY UNIT POWER SUPPLY UNIT has no service part. PDP-6071PU...

  • Page 44: Block Diagram And Schematic Diagram

    4. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM 4.1 OVERALL CONNECTION DIAGRAM (1/2) PDP-6071PU...
  • Page 45 ÷ The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. ÷ The encircled numbers denote measuring point in the schematic diagram. Waveforms, refer to service manual (ARP3395). PDP-6071PU...

  • Page 46: Overall Connection Diagram (2/2)

    4.2 OVERALL CONNECTION DIAGRAM (2/2) PDP-6071PU...
  • Page 47 Note 1 : ADD1446- (KUCXC only) ADD1470- (KUC and Regular only) (Note 1) (Note 1) PDP-6071PU...

  • Page 48: Overall Block Diagram

    4.3 OVERALL BLOCK DIAGRAM PDP-6071PU...
  • Page 49 PDP-6071PU...

  • Page 50: Address S And L Assys

    CLK / LE / HBLK / LBLK R/G/B VADR1 VADR1 VADR1 VADR1 VADR1 VDDLS1 VDDLS1 VDDLS1 VDDLS1 VDDLS1 RESONANCE RESONANCE RESONANCE RESONANCE RESONANCE RESONANCE BLOCK BLOCK BLOCK BLOCK BLOCK BLOCK IC1601 LVDS V+60V V+5V Reciever V+8V AN/P BN/P V+3V CN/P DN/P CLKN/P CN1601 CN1602 PDP-6071PU...

  • Page 51: Scan A And B Assys

    Signal Scan IC PSUS IC2801 VH IC5V Scan IC IC2802 VH IC5V Scan IC IC2803 VH IC5V Scan IC IC2804 VH IC5V Scan IC IC2805 VH IC5V Scan Signal Scan IC IC2806 IC5V 50 SCAN A ASSY (LOW SIDE) PDP-6071PU...

  • Page 52: Drive Assy

    4.6 60 X DRIVE ASSY 60 X DRIVE ASSY PDP-6071PU...
  • Page 53 X Drive power supply map from Power supply PDP-6071PU...

  • Page 54: Drive Assy

    4.7 60 Y DRIVE ASSY 60 Y DRIVE ASSY PDP-6071PU...
  • Page 55 Y Drive power supply map • VOFS and VPRST DC/DC converter are electric Vol control. PDP-6071PU...

  • Page 56: Digital Assy

    SUB-FILD CONV. SUB-FILD CONV. & XY DRV SEQUENCE XY DRV SEQUENCE PATTERN GEN. PATTERN GEN. LVDS LVDS PEG122C- K V+3V_D V+3V_D IC3401 IC3401 FlashMemory H DET IC3301 V+3V_D V+3V_D LED_R LED_B V+3V_D MSEL V+3VACT YOBI 60 DIGITAL ASS'Y AWV2365- PDP-6071PU...

  • Page 57: Audio Assy

    PSW_A REGULATOR IC3752 PQ120DNA1ZPH BUFFER +16.5V +12V POWER AMP IC WOW + VOLUME IC IC3751 IC3753 LA4625 NJW1183GK1 +12V BUFFER DC DETECT BLOCK A_Mute A_STBY_B R_Audio L_Audio MAIN Assy A_NG_B AUDIO ASS'Y R OUT L OUT SP TERMINAL ASSY PDP-6071PU...

  • Page 58: Signal Block Diagram

    KEY1/2 CN4006(2/2) LED_REC/MDM LED IR REM_B Assy IC7101 SIDE KEY KEY_AD1/AD2 IC7201 IC7001 Assy PCM1803D PE5436 TVP5160 CN4010 (GA) (VDEC) (ADC) PC Input HNM Assy IC6201 IC6301 BCM3517 (Elite Only) BCM7038 POD Card ETHER OPT Out G-LINK POD Assy PDP-6071PU...
  • Page 59 MB91305PMC TXD_IF/RXD_IF (MAIN UCOM) IC5401 CN4007 SII9023CTU (HDMI) RST_DT AUDIO_L/R TXD_AU RXD_AU TXD_DT RXD_DT AUDIO Assy IC8407 PQ200WNA1ZPH A0 to19 (FAN CONTROL) DQ0 to15 CN4006 CN4009 IC8402 Input5 Input6 (1/2) AGC1006 HDMI HDMI (FLASH) 42 & 60 LED Assy PDP-6071PU...

  • Page 60: Dtv Block Diagram

    CIMaX OOB_Data Logic Circuit [IC7302] I2C1 EBI BUS FLASH 32MBytes [IC6902] SPDIF out HSX_0 I2C0 SDRAM [IC6602] 256Mbit SDRAM BCM7038KPB1G-B2-K [IC6603] [IC6301] 256Mbit SDRAM [IC6604] 256Mbit SDRAM [IC6605] 256Mbit [12bit] Digital Video UARTA Gata ARRY [IC7201] From/To Main uCom PDP-6071PU...
  • Page 61 Audio L/R in Audio A/D [IC7101] From AV_SW ITU-R656 CVBS in VDEC [IC7001] I2C2 SDRAM [IC7002] 16Mbit Video out for monitor (Y, C) Audio L/R for monitor To AV_SW Audio L/R for PANEL (16bit) Digital Video out To Digital Selecter PDP-6071PU...

  • Page 62: Fukugo Block Power Line Block Diagram

    4.12 FUKUGO BLOCK POWER LINE BLOCK DIAGRAM AUDIO Assy POWER AMP +16_5V IC3751 LA4625 16.5V → 12V WOW+VOL IC +12V IC3752 IC3753 PQ120DNA1ZPH NJW1183GK1 60 IR Assy V+5.1V_STB IC9801 SBX3050-01 SIDE KEY Assy KEY Block V+3.3V_STB S9501 to S9507 PDP-6071PU...

  • Page 63: Power Supply Unit

    4.13 POWER SUPPLY UNIT PDP-6071PU...

  • Page 64: Voltages

    INPUT4_PLUG INPUT1_SC INPUT1_SC INPUT1_S2 INPUT1_S2 INPUT4_Y INPUT4_Y INPUT1_SPLUG INPUT1_SPLUG INPUT1_SY INPUT1_SY INPUT4_PB INPUT4_PB INPUT2_V INPUT2_V INPUT4_PR INPUT4_PR INPUT2_SC INPUT2_SC INPUT4_V INPUT4_V INPUT2_S2 INPUT2_S2 INPUT2_SPLUG INPUT2_SPLUG INPUT4_L INPUT4_L INPUT2_SY INPUT2_SY INPUT4_R INPUT4_R TEMP_2 TEMP_2 V+9V_A V+9V_A V+9V_A V+9V_A V+3.3V_UCOM V+3.3V_UCOM PDP-6071PU...
  • Page 65 V+3.3V_UCOM TEMP2_P TEMP2_P POD Assy MTB MAIN Assy CN9003(CKS3826-) (C3) CN4013(AKM1233- -TBB)(M10) Voltage Name Name PC_H PC_H PC_V PC_V PC_B 2.4* PC_B PC_G 2.4* PC_G PC_R 2.4* PC_R V+5V_A V+5V_A V+9V_A V+9V_A * When PC signal is not inputted. PDP-6071PU...
  • Page 66 LED_OFF LED_REC LED_REC MTB MAIN Assy LED_MDM LED_MDM CN4009(AKM1274- -TBB)(M4) Voltage LED- LED- Name Name 7.7/11 FAN_VCC FAN_NG1 TRAP-SW MTB MAIN Assy CN4018(AKM1213- -TFB)(M13) Voltage Name Name TRAP_SW V+3_3V_UCOM MTB MAIN Assy CN7101(AKM1276- -TBB)(M16) Voltage Name Name VBUS SHILD PDP-6071PU...
  • Page 67 AC state input TP3020 TXD_MD UART communication with MAIN u-com 0 to 3.3 TP3166 RXD_MD UART communication with MAIN u-com 0 to 3.3 TP3163 REQ_MD Communication demand to main system 0 to 3.3 TP3016 MODE Detection of MAIN Assy connection – PDP-6071PU...
  • Page 68 EXT_PD VSUS power supply adjustment signal TP3633 VSUS_ADJ Power supply PD signal TP3634 PS_PD Relay control TP3626 RELAY Large power supply ON/OFF control signal TP3616 DRF_B AC power supply state input TP3635 AC_DET Power down trigger signal TP3636 PD_TRG_B PDP-6071PU...
  • Page 69 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 70 – GND_LVDS – – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 71 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 72 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 73 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 74 – GND_LVDS – – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 75 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 76 – – GND_LVDS – – – – – V+3V_D +3.3 V power supply output – V+3V_D +3.3 V power supply output – – – – DIV_1 Data output timing control – DIV_0 Data output timing control – – – PDP-6071PU...
  • Page 77 Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial Non-connection termial DRF_SW DRF_SW DRIVE OFF signal input TP3623 Non-connection termial XSUS_PD XSUS_PD X DRIVE PD signal input TP3515 PDP-6071PU...
  • Page 78 Function standby control signal TP3516 SCAN_PD SCAN_PD Y DRIVE PD signal input TP3509 YDD_PD YDD_PD Y DRIVE PD signlal input TP3510 YSUS_PD YSUS_PD Y DRIVE PD signlal input TP3511 Non-connection termial YDRV_PD YDRV_PD Y DRIVE PD signal input TP3512 PDP-6071PU...
  • Page 79 Power supply for VH Non-connection termial Non-connection termial Non-connection termial GNDH GNDH GND(PSUS) SI_H SI_H SI_H signal CLR signal OC2 signal OC1 signal CLK1 CLK1 CLK1 signal LE signal GNDH GNDH GND(PSUS) GNDH_R GNDH_R GND(PSUS). Connector detection IC5V IC5V IC5V power supply PDP-6071PU...
  • Page 80 P2: (B8B-EH) Pin No. Name Voltage [V] Name Pin No. Function +16_5V 16.5 +16_5V 16.5V power supply +6_5V +6_5V 6.5V power supply GND_D GND_D GND_SUS GND_SUS GND_SUS GND_SUS Non-connection termial VSUS VSUS VSUS power supply VSUS VSUS VSUS power supply PDP-6071PU...
  • Page 81 Woofer output R+ (Speaker output R+) – RH– Tweeter output R– – RL– Woofer output R– (Speaker output R–) – Woofer output L+ (Speaker output L+) – Tweeter output L+ – LL– Woofer output L– (Speaker output L–) – LH– Tweeter output L– – PDP-6071PU...
  • Page 82 60 IR ASSY CN9801 (RE1) ↔ MAIN ASSY CN4010 (M8) Pin No. Pin Name Function Remarks V+5.1V_STB – Standby 5.1 V power supply – Remote control signal – – – – – – – – – – – – PDP-6071PU...

  • Page 83: Waveforms

    : Checkered pattern of Black- White (MKSS13) signal : Checkered pattern of Black- White(MKSS13) : L1730(V+ADR1)(side-A through hole) : L1730(V+ADR1)(side-A through hole) V: 10V/div H: 2ms/div V: 10V/div H: 500ns/div • VADR ( 2 SF) • VADR ( 1 Field) PDP-6071PU...

  • Page 84: Address Assy

    : Checkered pattern of Black- White (MKSS13) signal : Checkered pattern of Black- White(MKSS13) : L1730(V+ADR1)(side-A through hole) : L1730(V+ADR1)(side-A through hole) V: 10V/div H: 2ms/div V: 10V/div H: 500ns/div • VADR ( 2 SF) • VADR ( 1 Field) PDP-6071PU...
  • Page 85 (60 X DRIVE Ass'y) H : 2ms/div ch2 K2912(ScanOUT) - K2301(SUSGND) (60 Y DRIVE Ass'y) V : 50V/div H : 5us/div (607 SCAN A Ass'y LOWSIDE) ch3 F2301(YPSUS) - K2301(SUSGND) V : 50V/div H : 5us/div (60 Y DRIVE Ass'y) PDP-6071PU...

  • Page 86: Diagnosis Information

    Is there any local abnormality Is the abnormality associated Replace the panel chassis. with a single scan line? on the screen? with one address or one TCP? Failure analysis for the Failure analysis for the drive system ⇒ DR3 drive system ⇒ DR4 PDP-6071PU...
  • Page 87 Is an external video signal MAIN Assy ⇒ MA3 displayed properly? Problems concerning the audio output No Failure analysis for the Is the audio signal output? audio system ⇒ AU1 Specific failure whose cause is difficult to identify in the initial stage PDP-6071PU...

  • Page 88: Flowchart Of Failure Analysis For The Power Supply Unit

    Replace the POWER SUPPLY 200 and 210 V (VSU: 125/35°C). specified range? Unit. The ripple must be within 10 V. Replace the POWER SUPPLY Is there a fluctuation in the VSUS voltage? Unit. The POWER SUPPLY Unit is normal. PDP-6071PU...

  • Page 89: Flowchart Of Failure Analysis For The Digital Assy

    Replace the MAIN Assy. Replace the MAIN Assy. Is the indication position correct? It is most likely that the sync signal is abnormal. Is the tone correct? It is most likely that the video signal data are missing. Replace the MAIN Assy. PDP-6071PU...

  • Page 90: Flowchart Of Failure Analysis For The Drive Assy

    Is the input signal normal? Replace the FFC cables. Replace the DIGITAL Assy. (See the oscilloscope photos.) Is the waveform of the control signal from the SCAN Assy Replace the Y DRIVE Assy. normal? (See the oscilloscope photos.) Replace the SCAN Assy. PDP-6071PU...
  • Page 91 Assy normal? Is the cable connected properly Connect the cable properly. Care must be taken that no dirt or dust is attached or gets in. to the 90-pin connector? (The SCAN IC may be damaged.) Replace the SCAN Assy. PDP-6071PU...

  • Page 92: Flowchart Of Failure Analysis For The Main Assy

    If the voltage at Pin 129 (RST3 port) on the main microcomputer is high, it is judged that the AC power Replace the MAIN Assy. cord is not plugged in, and operation of the unit will stop there. PDP-6071PU...

  • Page 93: Flowchart Of Failure Analysis For The Video System

    Is the selected input signal an ⇒ COMP / S2 analog TV signal? Is the selected input signal a ⇒ DTV digital TV signal? Is the selected input signal a ⇒ USB USB signal? No problem with the MAIN Assy PDP-6071PU...
  • Page 94 IC5101 - pin 148 (s-video) IC5101 - pin 158 (s-video) V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div PDP-6071PU...
  • Page 95 IC5101 - pin 148 (s-video) IC5101 - pin 158 (s-video) V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div PDP-6071PU...
  • Page 96 IC5301 - pin 48 (PC) IC5301 - pin 54 (component) IC5301 - pin 54 (PC) V: 500 mV/div H: 10 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div PDP-6071PU...
  • Page 97 IC5301 - pin 54 (component) IC5301 - pin 54 (PC) V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 10 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div V: 500 mV/div H: 20 µsec/div PDP-6071PU...
  • Page 98 CN4005. If there is no ploblem, check the Flexible cable between CN4005 and CN8803. Check the communication between Is a signal output from jack? the CN8803 and Jack. If there was no ploblem replace IO Assy. Finishing troubleshooting. PDP-6071PU...

  • Page 99: Flowchart Of Failure Analysis For The Audio System

    IC4704 - pin 1, 7 (DC-SUBWOO) V: 200 mV/div H: 4 msec/div V: 1 V/div H: 10 msec/div V: 200 mV/div H: 4 msec/div V: 500 mV/div H: 4 msec/div Input signal: 100 Hz Sound volume is fixed to 25. PDP-6071PU...
  • Page 100 Is a signal come to IC6301? IC6301and IC7101. If there is no problem, replace IC7101. Is a signal output from IC6301 and Check the communication between come to CN4007? (pin 3, 5) CN4007 and IC6301. If there is no problem, replace IC6301. PDP-6071PU...
  • Page 101 Home Menu? Media Gallery. Replace or reconnect flexible Check the Flexible cable between HNM Assy and CN4017. cable. Check the communication between Is a signal input to IC4701? CN4005 and IC4701and replace broken parts. Finishing troubleshooting. PDP-6071PU...
  • Page 102 Is the signal input from IC7201 to Check between IC7201 and IC8001? IC8001. Exchange IC6301 if there is no problem. Has the symptom been settled The panel is defective. when the MAIN Assy is replaced? Finishing troubleshooting. PDP-6071PU...

  • Page 103: Power Down

    5.2 POWER DOWN 5.2.1 BLOCK DIAGRAM OF THE POWER-DOWN SIGNAL Block Diagram of the Power-Down Signal PDP-6071PU...

  • Page 104: Power Down Of Failure Analysis

    60 ADDRESS Assy 8 (ADR) CN2401, CN2402 60 SCAN Assy 4 (SCN-5V) 60 SCAN CN2901, CN2801 60 Y DRIVE Assy 4 (SCN-5V) CN1602, CN1802 60 DIGITAL Assy 8 (ADRS) 60 ADDRESS CN1601, CN1801 60 X/Y DRIVE Assy 8 (ADRS) PDP-6071PU...
  • Page 105 SCAN bridge (lower) connector disconnection detection Increase or decrease VOFS voltage detection Y_DD_PD (red: 6 times) Overvoltage VCPRST detection Overvoltage VC_15V detection Increase or decrease SCAN_PD (red: 3 times) voltage detection Overcurrent YDRV_PD (red: 5 times) 16.5V detection PDP-6071PU...

  • Page 106: Shut Down

    5.3 SHUT DOWN 5.3.1 BLOCK DIAGRAM OF THE SHUT-DOWN SIGNAL Block Diagram of the Shutdown Signal PDP-6071PU...

  • Page 107: Shut Down Of Failure Analysis

    5.3.2 SHUT DOWN OF FAILURE ANALYSIS PDP-6071PU...

  • Page 108: Non-Failure Symptoms

    8 bits each. In a case of color difference 4:2:2, Y, Cb, and Cr use 12 bits each, but Cb and Cr are transmitted at a half sampling rate of Y. This unit is capable of processing the upper 10 bits out of 12 bits of video data. Recent high-end DVD players, such as Pioneer DV-79AVi, are capable of outputting 10-bit color- difference signals.

  • Page 109: Disassembly

    MAIN Assy Assy Assy 60 ADDRESS L 60 ADDRESS S 60 ADDRESS S 60 ADDRESS L Assy Assy Assy Assy TANSHI SP TERMINAL 60 IR Assy 42 & 60 LED Assy Assy Assy Front view Front view Rear view PDP-6071PU...

  • Page 110: Flowchart Of The Main Parts And Pc Boards Exchange

    Side input Under cover (60) Tuner stay U POD stay A shield panel (U) shield 60 Y 60 X SIDE MAIN DRIVE DRIVE Terminal panel A TERMINAL Front chassis VL Assy 60 TANSHI 607 SCAN A 607 SCAN B PDP-6071PU...
  • Page 111 Remove the 22 screws. (APZ30P100FTB) Rear case (607) 1 1 1 1 1 1 Pull the lower part of the Front case Assy 607 Front case Assy 607 toward you and out. Remove the Front case Assy 607, by pulling it upward. PDP-6071PU...
  • Page 112 Remove the two handles. Rear case (607) ×3 ×3 Remove the 40 screws. (AMZ30P060FTB) ×11 Remove the six screws. (APZ40P100FTB) Remove the one screw. (ABA1341) Remove the rear case (607). Handle Sub frame cover L Sub frame cover R Handle PDP-6071PU...
  • Page 113 Disconnect cables, connectors, as required. POD Assy POD stay A Remove the POD cover. Remove the two hex. head screws. Remove the two screws. Remove the two screws. Remove the POD stay A with PCB. POD cover ×2 MAIN Assy PDP-6071PU...
  • Page 114 Remove the under cover (60). ×16 TANSHI Assy SP TERMINAL Assy Exchange of 607 SCAN A and B Assys Loosen the jumper wire. Remove the two screws. Remove the function button shield with PCB. Function button shield SIDE KEY Assy PDP-6071PU...
  • Page 115 607 SCAN A Assy 60 Y DRIVE Remove the 10 screws. Assy Disconnect the two pin connectors. Disconnect the 8 spacers. ×10 Remove the 607 SCAN A and B Assys. ×2 607 SCAN B Assy 607 SCAN A Assy Exchange PDP-6071PU...

  • Page 116: Adjustment

    Select “Channel Setup”. ( then ENTER) Select “POD ID”. ( • The Host ID and Cable Card ID appear. 5. Press HOME MENU to exit the menu. (*) : When replacing the MAIN Assy, be sure to do the FINAL SETUP. PDP-6071PU...

  • Page 117: Adjustment Required When Part Is Replaced

    60 ADDRESS Assy No adjustment required No adjustment is required after replacement of parts SENSOR Assy other than those mentioned above. No adjustment required TANSHI Assy (*) : When replacing the MAIN Assy, be sure to do the FINAL SETUP. PDP-6071PU...

  • Page 118: Backup When The Panel Unit Is Adjusted

    2 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 3 Issue the BCP command to transfer the data stored in the EEPROM for backup. 4 Turn the power off. PDP-6071PU...
  • Page 119 2 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 3 Issue the UAJ command to delete data stored in the EEPROM on the DIGITAL Assy. 4 Issue the BCP command to transfer the data stored in the EEPROM for backup. 5 Turn the power off. PDP-6071PU...
  • Page 120 When a DIGITAL Assy with an EEPROM in which adjustment data are stored is mounted, this step is not required after manual adjustment. ("DIGITAL EEPROM: REPAIR" is not indicated.) (2) Method using the RS-232C commands Issue the FAJ command. PDP-6071PU...

  • Page 121: Adjustments When The Service Panel Assy Is Replaced

    WBI S01 : Used to temporarily set the adjustment value of the Panel WB to default. (To return the value to its original value, use WBI S00.) PGM S00 : Used to set the gamma setting to Factory. Note: If the power is shut off in the process of the adjustment procedures, send the above commands again. PDP-6071PU...
  • Page 122 After the voltage adjustment is finished, make the following settings: Mask: OFF, Factory: OUT CA check Confirmation of setting data Check that the picture is properly displayed. Check that the each voltage is properly set. Use DVD, LD, and broadcast signals for checking. PDP-6071PU...
  • Page 123 10 minutes to raise the panel temperature to a certain extent. This ensures the accuracy of inspection and adjustment. (To 2 ) PDP-6071PU...
  • Page 124 Vofs_min2. Replace the panel Is Vofs_min2 144 (38 [V]) again or abnormality or smaller? in circuits Note: Return the Vofs value to the tentative This is for checking the lower limit of Vofs accurately. voltage setting. (To 3 ) PDP-6071PU...
  • Page 125 This is for checking the lower limit of Vofs accurately. voltage setting. Vofs_min Set the highest voltage among Vofs_min1, Vofs_ [STEP] min2 and Vofs_min3 as Vofs_min. Note: Take note of the lower limit color of Vofs (To 4 ) (pale purple or sky color or yellow egg color). PDP-6071PU...
  • Page 126 Vofs_max2. Replace the panel Is Vofs_max2 113 (32 [V]) again or abnormality or greater? in circuits Note: Return the Vofs value to the tentative This is for checking the lower limit of Vofs accurately. voltage setting. (To 5 ) PDP-6071PU...
  • Page 127 Value for Vofs = Vofs_max - 41 (8 [V]) 116 (23 [V]) or greater? Value for Vofs = Vofs_max - 61 (12 [V]) Set the Vofs as value for Vofs . (To 6 ) Vofs margin = Vofs_max - Vofs_min * Vofs= * Vofs Margin = determined PDP-6071PU...
  • Page 128 Turn the Mask off: Return to initial settings. Exit Factory mode: CA check Turn the unit off then back on again: POF, PON Use input signals from a DVD or PC for CA checking. Check that no bright cells or dark cells. PDP-6071PU...
  • Page 129 Conversion charts for electronic VRs (Vprst/Vofs) Vprst Setting value Vofs Setting value [STEP] [STEP] PDP-6071PU...

  • Page 130: Adjustments When The Drive Assys Are Replaced

    DIGITAL Assy XSUS-B SUS-G ADJUSTMENT 1 Measure the SUS-D input delay time (∆ Tsus-d). from DIGITAL Assy XSUS-D 2 Adjust the SUS-G input delay time so that it becomes "∆ Tsus-d + β ± 5 nsec." from DIGITAL Assy XSUS-G PDP-6071PU...
  • Page 131 DIGITAL Assy YSUS-B SUS-G ADJUSTMENT 1 Measure the SUS-D input delay time (∆ Tsus-d). from DIGITAL Assy YSUS-D 2 Adjust the SUS-G input delay time so that it becomes "∆ Tsus-d + β ± 5 nsec." from DIGITAL Assy YSUS-G PDP-6071PU...
  • Page 132 Assy Time SUS-G delay time: ∆ Tsus-g Adjust so that "∆ Tsus-g = ∆ Tsus-d + β ± 5 nsec," using the variable X DRIVE VR1001 120 nsec controls shown in the table below: Y DRIVE VR2011 100 nsec PDP-6071PU...

  • Page 133: How To Clear History Data

    P COUNT INFO. < = > : NO OPRT P COUNT INFO. < = > : CLEAR Right SET (5 sec) MAX TEMP. < = > : NO OPRT Right MAX TEMP. < = > : CLEAR SET (5 sec) 3 Turn the power off. PDP-6071PU...

  • Page 134: Procedure When Replacing The Power Supply Unit

    Location of the jumper connector 2. Remove the jumper connector from connector 1. As for service parts, the Jumper connector is P10 and connect it to connector P11. connected at connector P10. 3. Connect the cable connector from power SW to P10. PDP-6071PU...

  • Page 135: Service Factory Mode

    How to come off Service Factory Mode. Case operated by remote control) • Service remote control : press [ FACTORY1 ] key. • Remote control : press [ HOME MENU ] key. Case to RS-232C transmit command) • Send [FAN] . PDP-6071PU...

  • Page 136: Operation Of Service Factory Mode

    (screenize switching, etc). • Data on screen (i.e.,screen position; meaning clock dividers, and not including data on screen size) Are reset to the default values (data stored in memory will be retained). Screen size will be retained. PDP-6071PU...

  • Page 137: Remote Control Code

    : When ten seconds have passed since the [ DRIVE ON/OFF ] key was pressed at the standby, it becomes invalid. Please press [ POWER ] key from the [ DRIVE ON/OFF ] key pressing within ten seconds when you do power supply ON while driven OFF. Remote Control Unit for Servicing PDP-6071PU...

  • Page 138: Configuration Of Factory Mode

    INTR-POS1(0x75) ⇔ 8.2.4.8 HDMI INTR POSITION (+) 000 to 255 for technical analysis INTR-POS2(0x76) ⇔ 000 to 255 for technical analysis INTR-POS3(0x77) ⇔ for technical analysis 000 to 255 INTR-POS4(0x78) ⇔ 000 to 255 for technical analysis PDP-6071PU...

  • Page 139: Indication (Osd) Of Service Factory Mode

    Note: See SIG-Mode Tables.(See next page.) Color system and Signal type Color system and signal type NTSC Composite input S-connector input Y/CB/CR Y/PB/PR Digital video signal Option(Destination, Panel Generation, etc) Options SX System in North America(Regular) ATB7 SX system in North America(ELITE) AHB7 PDP-6071PU...
  • Page 140 46.875 1024x768 60.004 48.363 70.069 56.476 75.029 60.023 1360x768 60.015 47.712 Selection of the screen size by the user is displayed. GUI Notation VIDEO Remark Character DOT BY DOT FULL (FULL1) ZOOM CINEMA WIDE FULL2 : supported, : unsupported PDP-6071PU...

  • Page 141: Factory Menu

    In the 29-32 rows, ROM version information on each device is displayed. In the 19-24 rows, Version information on a common treatment is displayed. At the position "14x35", The Past/Highly effective panel distinction information is displayed. " P " : The past panel, "F" : The highly effective panel PDP-6071PU...
  • Page 142 CFE Version HHHHHHHH KERNEL Version KERNEL HHHHHHHH ROOTFS Version ROOTFS HHHHHHHH FLAGS FLAGS (Y) FONTS(Y) DFTS (Y) PLOG (Y) 8.2.1.3 VERSION(3) Flash Device Item Name Elite Regular CCD-UCOM Version MSKB HMG/HG module Version HMG/HG 0123456789 User Password PASSWORD 1234 PDP-6071PU...
  • Page 143 - TV-Guide Error HOME-G - Failure at Home Gallary MA-PWR M-DCDC -Abnormally in RST2 of MAIN Assy (power decrease of DC-DC converter) RELAY -Abnormally in RST4 of MAIN Assy (power decrease of Relay power) Failure at Home Media Gallary START PDP-6071PU...
  • Page 144 Even if [ ← ] key or [ → ] key is pushed, "CLEAR ⇔ YES" ⇔ "CLEAR ⇔ NO" is repeated. If the [ ENTER ] key is kept on pressing for 5 second when the status of this menu is <YES>, clear process will begin. PDP-6071PU...

  • Page 145: Hour Meter

    In HOUR METER screen on Factory Menu, press the [ENTER] key, and then it moves to the screen to clear MTB HOUR METER. Display/Meaning: Meaning Item Name RS-232C command HOUR METER(PANEL) PANEL 00151H 21M HOUR METER(MTB) 00151H 21M – POWER ON COUNTER P-COUNT 00000095 TIMES SYSTEM SERIAL SERIAL PDP-6071PU...
  • Page 146 Video information: valid horizontal pixel numbers (low order bit) - 3B: Video information: valid horizontal pixel numbers (high order bit) - 3C: Video information: valid vertical line numbers (low order bit) - 3D: Video information: valid vertical line numbers (high order bit) PDP-6071PU...
  • Page 147 H RES V RES H DE V DE V FMT 480i (525i) 262 or 263 720x480i @ 60 480p (525p) 720x480p @ 60 1080i (1125i) 2200 562 or 563 1920 1920x1080i @ 60 720p (750p) 1650 1280 1280x720p @ 60 PDP-6071PU...
  • Page 148 Displays input signal status of MVDEC terminal. Device Context MVDEC Signal distinct result 1 Signal distinct result 2 Flag detection output Noise level distinction 1 Noise level distinction 2 Non-standard signal detection Sub carrier signal detection ACC data output ACC information output Input signal mode PDP-6071PU...
  • Page 149 Displays digital broadcast signal information and status upon receiving digital signal. 8.2.1.13 DTV TV-GUIDE BER Exclusively used for production line. TV-Guide error bit ratio information is displayed. 8.2.1.14 DEBUG INFO Exclusively used for technical analsyis. Debug information for development use is displayed. PDP-6071PU...

  • Page 150: Panel Factory Mode

    8.2.2.9 RASTER MASK SETUP (+) The mask indication (RASTER) can be set and indicated. 8.2.2.10 PATTEN MASK SETUP (+) The mask indication (PATTERN) can be set and indicated. 8.2.2.11 COMBI MASK SETUP (+) The mask indication (COMBI) can be set and indicated. PDP-6071PU...

  • Page 151: Panel Information

    • P-COUNT: The accumulated power-on count is indicated. • TEMP1: The current panel temperature and the historical maximum temperature recorded in memory are indicated. The range of temperature indication is from -50.0 to +99.9. (The temperature unit is " °C (Centigrade) ".) PDP-6071PU...
  • Page 152 Drive Sequence Processing IC SQ-IC Drive Sequence Stop SQNO Communication Busy BUSY Version Mismatching VER-HS MAIN EEPROM Communication Error EEPROM MDU-IIC MD-IIC BACKUP EEPROM Communication Error BACKUP DAC Communication Error High temperature of the panel TMP-NG Temperature NG TEMP PDP-6071PU...
  • Page 153 : Subtracting by one from the adjustment/setting value <VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
  • Page 154 : Subtracting by one from the adjustment/setting value <VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
  • Page 155 <DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
  • Page 156 <DOWN> : Shifting to the next item <UP> : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6071PU...
  • Page 157 Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...
  • Page 158 Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...
  • Page 159 Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. • 48 V and 60 P are deleted from the sequence, and represented by 50 V and 60 V, respectively. The ABL/WB table is changed to the PC table. PDP-6071PU...

  • Page 160: Option Mode

    If the signal is changed to cable, then the cable’s broadcast map is configured, and air’s broadcast map is destroyed. OSD display Funcrion Control device CABLE Change the antenna setting to cable Change the antenna setting to air 8.2.3.3 AFT Exclusively used for production line. PDP-6071PU...

  • Page 161: Initialize Mode

    DIG MVDEC YCBCR MAIN VDEC: YCbCr (Digital output mode) ANA MVDEC YCBCR MAIN VDEC: YCbCr (Analog output mode) ANA MVDEC Y MAIN VDEC: Y (Analog output mode: SG VDEC return setting) ANA AD YCBCR AD: YCbCr ANA AD RGB AD: RGB PDP-6071PU...
  • Page 162 For this account the latter part from MVDEC does not have set values, resulting in having funny colors in colorbar, the brightness changes after switching, etc. This is not a damage result nor error. • Depending on MVDEC’s part version, ANA_MVDEC_YCBCR may not display colors. PDP-6071PU...
  • Page 163 When the configuration is set to <YES> and the [SET] key is pressed for 5 seconds, the reset action executes. Be sure to disconnect and connect the Power cord after the FINAL SETUP. When replacing the MAIN ASSY, the FINAL SETUP is required. PDP-6071PU...
  • Page 164 For ELITE model Be sure to do above procedure at input fuction except HMG. 2nd FACTORY MODE [ Home Gallery ] (Regular Model) 1. Home Gallery Screen (1) When the device is connected (2) When the device is not connected PDP-6071PU...
  • Page 165 0 E (Endpoint descriptor info) - E (Endpoint descriptor info) Endpoint Address (I=In, O=Out) Hexadecimal(String) Attributes Hexadecimal(String) MxPS Endpoint Max Packet Size Decimal Interval (max) between transfers Decimal 2. End method It is the same as the case that Home Gallery displays. PDP-6071PU...

  • Page 166: List Of Rs-232C Commands

    During standby mode, press the [Home Menu] key, and then press the [POWER] key within 3 seconds. Or during Factory mode, hold the [INTEGRATOR] key. #In INTEGRATOR MENU, there is a OSD where SR+(or RS-232C) is turned on/off, and it switches on the screen. PDP-6071PU...

  • Page 167: Command Protocol

    ETX, the character string sandwiched between STX and ETX is recognized as a command. If the prepared character string storage buffer (24 bytes including STX, ID and ETX) is exceeded, a reply will not be sent out. PDP-6071PU...

  • Page 168: Definition Of Command

    The data length will be subject to each individual specification as the content of a reply will be different depending on the type of QUEST command. Data transmitted from PC Reply data Command Command Parameter ∗∗ 0x02 0x03 0x02 • • • • • • • • • 0x03 PDP-6071PU...

  • Page 169: List Of Rs-232C Commands

    Factory mode on ¶ Set each memory setting of MTB side to the shipment state. MDU MTB ∗∗∗ ¶ User white balance : GREEN highlight ∗∗∗ ¶ User white balance : GREEN lowlight ¶ ¶ Green side mask level adjustment PDP-6071PU...
  • Page 170 Window (Hi= 1023) 4 % ¶ ¶ Window (Hi= 1023) 1.25 % ¶ ¶ Window (1/7 LINE) ¶ ¶ STRIPE (MGT/GRN) ¶ ¶ STRIPE (GRN/MGT) ¶ ¶ B & W, checker (1 line) ¶ ¶ B & W, checker (2 lines) PDP-6071PU...
  • Page 171 ¶ RASTER17: Pale purple ¶ ¶ RASTER18: Magenta 53 ¶ ¶ RASTER19: Red 1023+ ¶ ¶ RASTER20: Green 1023+ ¶ ¶ RASTER21: Blue 1023+ ¶ ¶ RASTER22: Red 588+ ¶ ¶ RASTER23: Green 588+ ¶ ¶ RASTER24: Blue 588+ PDP-6071PU...
  • Page 172 ¶ Acquiring data on the status of the unit, such as temperature Acquiring unit data, such as the software version common ¶ to all models, regardless of destination ¶ Acquiring data on shutdown PDP-6071PU...
  • Page 173 Setting the screen size to WIDE – – MDU MTB ¶ Determining the flag for the DIGITAL Assy adjustment in "not adjusted" To add ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, ¶ UP∗ designated by a function command) PDP-6071PU...
  • Page 174 Y-SUS-B ADJ ∗∗∗ ¶ ¶ Y-SUSTAIL T2 ADJ ¶ ∗∗∗ ¶ Y-SUSTAIL T1 ADJ ¶ ∗∗∗ ¶ Y-SUSTAIL W ADJ ¶ ¶ Initializing the video EEPROM data ¶ ¶ Initializing the setting data to which no adjustment command is provided PDP-6071PU...

  • Page 175: Outline Of Commands

    TXC / Re gula r (US) J Japan (reserved) S System model B Not used.( For Future) B All-in-one design TV Regular D Panal Type Regular A M Monitor P the past D Standard module F High-effective E Simple module PDP-6071PU...

  • Page 176: Qs2

    Adjustment not completed 11: Operation status 13: MASK indication X-DRV induced by SD X-DCDC MASK-OFF Normal X-SUS MASK-ON 3: Adjustment-data Relay-off completed backup Not used During warning Not used With backup data indication Not used No data (default) UNKNOWN PDP-6071PU...

  • Page 177: Qip

    RYW adjustment value 3 Byte R-REVICE setting value 1 Byte G-REVICE setting value 1 Byte B-REVICE setting value 1 Byte 2 Byte • For each REVICE setting value, the level set for RRL, RGL, or RBL is transmitted as one character. PDP-6071PU...

  • Page 178: Qpw

    To acquire data on operations of the panel Return data: 3 (ECO)+40(DATA)+2(CS)= 45 Byte Data Data Arrangement Output Example Length 3Byte Pulse meter B 1 8Byte 00000000 Pulse meter B 2 8Byte 00000000 Pulse meter B 3 8Byte 00000000 Pulse meter B 4 8Byte 00000000 Pulse meter B 5 8Byte 00000000 2Byte PDP-6071PU...

  • Page 179: Qpd

    Data from the hour meter for the seventh latest PD 8 Byte 00000213 Eighth latest "1st PD" data 1 Byte Eighth latest "2nd PD" data 1 Byte Data from the hour meter for the eighth latest PD 8 Byte 000001A7 2 Byte PDP-6071PU...

  • Page 180: Qsd

    Data from the hour meter for the seventh latest SD 8byte 00000000 BACKUP Eighth latest SD data 1byte Eighth latest SD subcategory data 1byte Data from the hour meter for the eighth latest SD 8byte 00000000 ¶ SD subcategory (TEMP) 2Byte No SD-Sub data TEMP1 Reserved PDP-6071PU...

  • Page 181: Qs6

    1 byte FLAGS Information 3 1 byte FLAGS Information 4 1 byte FLAGS Information 5 1 byte FLAGS Information 6 1 byte Version of CCD-UCOM 4 byte HMG/HG MODELE Version 10byte User Password 4 byte Check Sum 2 byte PDP-6071PU...

  • Page 182: Qsi

    1 Byte Result of detection of cracking in the panel 1 Byte Result of detection for scanning protection 1 Byte Result of detection for external protection 1 Byte Transition of protection operation 1 Byte ∗∗∗∗ Reserved 4 Byte 2 Byte PDP-6071PU...

  • Page 183: Qmt

    <No.1 Subcategory Information on "failure in 3-wire serial communication of Main microcomputer"> Data Cause of shutdown Remarks Non subcategory IF microcomputer communication failure IF (immediately Power Supply OFF) MANTA communication failure (MULTI1) MULTI1 (immediately Power Supply OFF) MANTA communication failure (I/P) MANTA communication failure (D-SEL) D-SEL PDP-6071PU...

  • Page 184: Drv

    9.3.13 DRV 7 DRV Drive ON/OFF : ON/OFF control for only the large-power system Remarks Effective Condition Function Format [DRV+S00] Every time DRIVE OFF At standby mode, when 10 seconds passed after issuing [DRV+S00], command becomes invalid. [DRV+S01] DRIVE ON PDP-6071PU...

  • Page 185: Commands For Prohibition/Permission Of Dtv/Homenet Communication

    • While ZACS01 is established, the LED for ZAC flashes. The priority of LED indications is as follows: PD > Trap-SW > DTV_STB > SD > ZAC >DTN > no backup copy > Standalone operation of the Assy > Normal ON/OFF • Even if DTNS00 is established, if ZACS01 is established, DTV/HomeNet communication must be prohibited. PDP-6071PU...

  • Page 186: Other Commands

    To make the flag setting that [CBU] Writing F0 to the 2 k byte ROM The backup ROM is indicating that backup data initialized. have not been copied To copy Digital backup data [BCP] Copying backup data to EEPROM PDP-6071PU...

  • Page 187: General Information

    4 : The MOD microcomputer controls the relay of the power MOD of the PDP to startup the power of the PDP. 5 : The main microcomputer controls the ASIC power within the MTB to startup the power of the MTB. PDP-6071PU...

  • Page 188: Power Supply Transition Status

    10.2 POWER SUPPLY TRANSITION STATUS PDP-6071PU...
  • Page 189 RST4 A_STBY RST2 From A V+35V PSW1 V+16.5V PSW1 V+12V V+6.5V DCDC DCDC DCDC V+5.1V Vsus Vadr Audio MVDEC F.E. A/B Volume SVDEC RGB-SW SQ ASIC block HDMI AV-SW DSEL Drive Address Address Drive Drive MULTI X&Y-Drive/Scan/Address Power supply PDP-6071PU...
  • Page 190 RST4 A_STBY RST2 From A V+35V PSW1 V+16.5V PSW1 V+12V V+6.5V DCDC DCDC DCDC V+5.1V Vsus Vadr Audio MVDEC F.E. A/B Volume SVDEC RGB-SW SQ ASIC block HDMI AV-SW DSEL Drive Address Address Drive Drive MULTI X&Y-Drive/Scan/Address Power supply PDP-6071PU...

  • Page 191: Power On/Off Function For The Large-Signal System

    Command [DRVS00/S01] is effective even during standby. When the main power is turned OFF, however, [DRVS01] (release) will be effective. Short the two adjacent electrodes on the surface by a method which assures continuity, such as using a crocodile clip. 60 DIGITAL Assy PDP-6071PU...

  • Page 192: Led Information

    10.4 LED INFORMATION LED Pattern PDP-6071PU...

  • Page 193: Specification About The Thermal Protection

    Fan Operation According to the reading value of above table sensor. HIGH or LO FAN_CONT: "L" [ Outline Circuit ] FAN_vcc Vref = 2.64V H : Vo = 11V L : Vo = 7.6V U-COM FAN_CONT H: On L: Off PDP-6071PU...

  • Page 194: Processing In Abnormality

    Specifications for port monitoring Port Name SD/PD Indication Assigned Pin Active FAN_NG 1 Shutdown with H Abnormally high Shutdown when the TEMP2 temperature in the value exceeds the predetermined value TRAP_SW Circuit diagram TRAP_SW MTB MAIN Assy V_3.3V_UCOM TRAP_SW MAIN_UCOM PULL_D PDP-6071PU...

  • Page 195: Trap Sw

    TRAP SW on ahead, carry out following procedure from this state. Cancelling by the remote control • Enter to the Factory mode. • Then, proceed to INITIALIZE layer inside the Factory mode, and then press "DISPLAY" key for more than 5 seconds. PDP-6071PU...

  • Page 196: Specifications

    HDCP (High-bandwidth Digital Content Protection) is a technology used to protect copyrighted digital contents that use the Digital Visual Interface (DVI). ** This conforms to USB 1.1 and 2.0 . Design and specifications are subject to change without notice. PDP-6071PU...

  • Page 197: Accessories

    (for PDP-6071HD only) Terminal position sheet (for use when mounting the Plasma Display on the wall) (AAX3330) Buttons used for only basic operations are provided on the simplified remote control unit. You can use it as necessary. PDP-6071PU...

  • Page 198: Panel Facilities

    For details, refer to the operation manual that 7 INPUT button (ENTER button*) came with the stand or speaker. 8 VOLUME UP/DOWN buttons (UP/DOWN buttons*) The buttons with asterisks (*) can operate the TV Guide On Screen™ system. 9 CHANNEL UP/DOWN buttons (LEFT/ RIGHT buttons*) PDP-6071PU...
  • Page 199 PDK-TS15U for the PDP-6071HD/ 13 INPUT 3 terminals (AUDIO) PDP-6070HD 14 INPUT 3 terminals (COMPONENT VIDEO: Y, 28 Speaker: PDP-S41 For details, refer to the operation manual that 15 INPUT 2 terminals (COMPONENT VIDEO: Y, came with the stand or speaker. PDP-6071PU...

  • Page 200: Remote Control Unit

    All buttons on the main remote control unit are luminous and gather and store light. This enables quick access to the desired function when performing operations in dark places. NOTE When using the remote control unit, point it at the Plasma Display. PDP-6071PU...

  • Page 201: Ic Information

    OUT47 OUT19 OUT46 OUT20 OUT45 OUT21 OUT44 OUT22 OUT43 OUT23 OUT42 OUT24 OUT41 OUT25 OUT40 OUT26 OUT39 OUT27 OUT38 BLOCK DIAGRAM Level Shift OUT1 Circuit Data Level 1-30, Shift 46-76, OUT2 - OUT63 Circuit Level Shift OUT64 Circuit Data PDP-6071PU...
  • Page 202 All output reset CLR terminal : L → normal operation, CLR terminal : H→ All output "H" − 93 - 94 GND1 − N.C. Not used − 96 - 97 Power for High-voltage circuit − N.C. Not used 99 - 100 OUT1 - OUT2 High-voltage push-pull output PDP-6071PU...
  • Page 203 USB 2.0 Digital Dual Audio 2x I S Ports Channel USB 1.1 1x SPDIF Audio Processor Analog Ethernet Audio 2x Dual Audio DDR-DRAM Controller DACs EJTAG Peripherals (200 MHz) Dual SATA S-ATA 64-bit wide DDR DRAM Test IR/LED/Key/UART SPI/BSC/GPIO/PWM SmartCard PDP-6071PU...
  • Page 204 R5520H001B (MAIN ASSY : IC7105) • USB HIGH-SIDE SW IC BLOCK DIAGRAM GATE CURRENT CONTROL LIMIT FLAG DELAY UVLO THERMAL SHUTDOWN PIN LAYOUT PIN FUNCTION Function Pin No. Name Enable terminal GND terminal FLAG terminal (Open-drain output) Power input terminal Output terminal PDP-6071PU...
  • Page 205 R2S11002AFT (MAIN ASSY: IC4701) • AV SW Block Diagram PDP-6071PU...
  • Page 206 R2S11001FT (MAIN ASSY: IC4901 • Component SW IC Block Diagram PDP-6071PU...
  • Page 207 UPD64015AGM-UEM (MAIN ASSY : IC5101) • Video decoder (for main screen) Block Diagram PDP-6071PU...
  • Page 208 AVDDA AVDD3 AGNDA AVDD3 IOCB VRT2 AVDDA ASCI AGNDA VRB2 IOYG AVDDA VCOM2 RSET ACBI VRT3 AGNDA DVDD1 VRB3 DGND VCOM3 AVDD3 DVDD3 AVDD3 VCOM4 SDRDQ15 SDRDQ0 ACRI VLPF2 SDRDQ14 SDRDQ1 VRB4 DVDD1 VRT4 SDRDQ13 AGND SDRDQ2 AGND DGND PDP-6071PU...
  • Page 209 Digital 3.3V power supply Connect to the 3.3V power supply. 109,120,132 DGND 17,24,33,38,45,56, – – Digital ground – 80,89,93,104,114, 2.2 System reset terminal Acronyms Terminal number Level Buffer type Functions PU/PD [kΩ] RSTB Schmitt – System reset input (Active-Low) PDP-6071PU...
  • Page 210 Connect to GND normally. VLPF1 Analog – Analog test output Connect to GND via a 0.1µF capacitor. VLPF2 Analog – Analog test output Connect to GND via a 0.1µF capacitor. Caution: Connect these terminals for test to GND unless otherwise instructed. PDP-6071PU...
  • Page 211 Digital RGB/B signal input DCRI LVTTL – Digital RGB/R signal input FCSI LVTTL 3 mA Sync separation signal input/timing output (HD) for RGB input. 3-state It will become Hi-Z when FCSIS[2:0] (SA22h, D2-D0)=000b. Normally, set to FCSIS[2:0]=0 and leave it open. PDP-6071PU...
  • Page 212 ADC2 top reference voltage Connect to GND via a 0.1µF capacitor. VRB2 Analog – ADC2 bottom reference voltage Connect to GND via a 0.1µF capacitor. VCOM2 Analog – ADC2 in-phase reference voltage Connect to GND via a 0.1µF capacitor. PDP-6071PU...
  • Page 213 Color difference component Cb/RGB component B output signal. Connect to AGNDA via a 200Ω load resistance. Analog – External reference input pin. Supply 1.0V. And, connect to AGNDA via a 0.1µF capacitor. RSET Analog – Connect to AGNDA via a 620Ω resistor for external adjustment. PDP-6071PU...
  • Page 214 3 mA Horizontal sync signal output 3-state LVTTL 3 mA Vertical sync signal output 3-state VBLK LVTTL 3 mA V blanking output 3-state FILD LVTTL 3 mA Field output 3-state RDEO LVTTL 3 mA Effective pixel range output 3-state PDP-6071PU...
  • Page 215 3 mA Address output for external memory -SDRA11 3-state Insert a damping resistor of approximately 100Ω, 13,12,10,9,8, and connect to the SDRAM address terminal. 7,6,5 SDRDQ0 51,49,46,42, LVTTL 6 mA Data input/output for external memory. 3-state -SDRDQ15 40,36,34,30, 31,35,37,41, 43,47,50,52 PDP-6071PU...
  • Page 216 (Not to Scale) BLUE <7> SOGIN BLUE <6> BLUE <5> BLUE <4> BLUE <3> BLUE <2> BLUE <1> BLUE <0> 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 PDP-6071PU...
  • Page 217 1, 10, 20, 21, 24, 25, 28, 32, 36, 40, 41, 44, 47, 50, 53, 60, 61, 63, 68, 80 Control Serial Port Data I/O 3.3 V CMOS Serial Port Data Clock (100 kHz Maximum) 3.3 V CMOS Serial Port Address Input 1 3.3 V CMOS PDP-6071PU...
  • Page 218 Hsync is active; the trailing edge is ignored. When Hsync Polarity = 0, the falling edge of Hsync is used. When Hsync Polarity = 1, the rising edge is active. The input includes a Schmitt trigger for noise immunity, with a nominal input threshold of 1.5 V. VSYNC Vertical Sync Input The input for vertical sync. PDP-6071PU...
  • Page 219 The designer should provide quiet, noise-free power to these pins. Ground The ground return for all circuitry on-chip. It is recommended that the AD9985 be assembled on a single solid ground plane, with careful attention given to ground current paths. PDP-6071PU...
  • Page 220 Control Signals EVNODD Video Color HS,VS, HSYNC Space Converter VSYNC R0XC ± PanelLink 24-Bit Up/Down ODCK Data TMDS Sampling R0X0 ± Q[23:0] Digital R0X1 ± CLK48B Core R0X2 ± Auto A/V Port Exception MUTEOUT Handling Detect SCDT R0PWR5V R1PWR5V PDP-6071PU...
  • Page 221 CGND DSDA1 CSCL CSDA IOVCC IOGND CGND CVCC18 CVCC18 SiI 9023 MCLKOUT CGND IOVCC 144-Pin IOGND CGND TQFP CVCC18 IOVCC IOGND AUDPVCC18 AUDPGND XTALOUT XTALIN XTALVCC REGVCC EVNODD RSVDL RESET# SCDT IOVCC CVCC18 IOGND VSYNC CGND CLK48B HSYNC IOGND PDP-6071PU...
  • Page 222 Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output LVTTL Output Data enable. HSYNC LVTTL Output Horizontal Sync Output control signal. VSYNC LVTTL Output Vertical Sync Output control signal. ODCK 12 mA LVTTL Output Output Data Clock. PDP-6071PU...
  • Page 223 2. CLK48B is used to clock external 24-to-48 bit latches. CLK48B is also latched on the rising edge of RESET# to set the I2C device addresses for CSCL/CSDA. Refer to Table 10. CLK48B has a weak internal pull-down, and so will be latched as a LOW if not otherwise connected. PDP-6071PU...
  • Page 224 PVCC1 Power TMDS Port 1 PLL VCC 3.3V TMDSPGND Ground TMDS PLL GND AUDPVCC18 Power ACR PLL VCC 1.8V AUDPGND Ground ACR PLL GND XTALVCC Power ACR PLL Crystal Input VCC 3.3V REGVCC Power ACR PLL Regulator VCC 3.3V PDP-6071PU...

This manual is also suitable for:

Pdp-6070pu

Table of Contents