Intel ulv celeron m 600mhz, 1.8ghz processors compact board with lvds, 10/100 ethernet, 6 channel audio & mini pci (59 pages)
Summary of Contents for Aaeon AEC-6643
Page 1
AEC-6643 Fanless Embedded Box PC User’s Manual 2 Last Updated: September 19, 2016...
Page 2
AAEON assumes no liabilities resulting from errors or omissions in this document, or from the use of the information contained herein. AAEON reserves the right to make changes in the product design without notice to its users.
Page 3
Acknowledgement All other products’ name or trademarks are properties of their respective owners. Microsoft Windows is a registered trademark of Microsoft Corp. Intel, Pentium, Celeron, and Xeon are registered trademarks of Intel Corporation Core, Atom are trademarks of Intel Corporation ...
Page 4
Packing List Before setting up your product, please make sure the following items have been shipped: Item Quantity BOXER-6643 Screw package Wall mount brackets DVD-ROM for manual (in PDF format) and drivers If any of these items are missing or damaged, please contact your distributor or sales representative immediately.
Page 5
(if any), its specifications, dimensions, jumper/connector settings/definitions, and driver installation instructions (if any), to facilitate users in setting up their product. Users may refer to the AAEON.com for the latest version of this document. Preface...
Page 6
All cautions and warnings on the device should be noted. All cables and adapters supplied by AAEON are certified and in accordance with the material safety laws and regulations of the country of sale. Do not use any cables or adapters not supplied by AAEON to prevent system malfunction or fires.
Page 7
As most electronic components are sensitive to static electrical charge, be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and contain all electronic components in any static-shielded containers. If any of the following situations arises, please the contact our service personnel: Damaged power cord or plug Liquid intrusion to the device iii.
Page 8
FCC Statement This device complies with Part 15 FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation. Caution: There is a danger of explosion if the battery is incorrectly replaced.
Page 10
China RoHS Requirement (EN) Poisonous or Hazardous Substances or Elements in Products AAEON Embedded Box PC/ Industrial System Poisonous or Hazardous Substances or Elements Hexavalent Polybrominated Polybrominated Component Lead Mercury Cadmium Chromium Biphenyls Diphenyl Ethers (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) PCB &...
Specifications System ® Intel Atom D2550 B3 Processor Memory DDR3 800/1066 Mhz SODIMM x 1, up to 4 GB Display Interface DB-15 x 1 DVI-D x 1 Ethernet Realtek RTL-8111E, 10/100/1000Base-TX x 2 Storage Device SATA 3.0Gb/s 2.5” HDD bay x 1 ...
Page 15
Mechanical Aluminum Alloy Chassis Construction Dark Gray Color Wall mounted Mounting 11.81" x 3.05" x 7.48" Dimension (W x H x D) (300mm x 77.5mm x 190mm) Gross Weight 12.98 lb (5.9 kg) Net Weight 6.00 lb (2.7 kg) ...
List of Jumpers Please refer to the table below for all of the system’s connectors that you can configure for your application. Label Function ATMODE AT/ATX Mode Selection CLRTC Clear COMS DIGITALREFENCE COM2 External Power Selection LVDS_VDD_SEL LVDS Panel Power Selection L_BRIGHTNESS LVDS Brightness Control Type Selection LVDS_SWITCH...
2.3.3 COM2 External Power Selection (DIGITALREFENCE) DIGITALREFENCE Function Close 15-16 +12V Close 17-18 RI# (Default) Close 19-20 2.3.4 Watchdog Timer Function Switch (WDT) Function Close 1-2 Disable (Default) Close 2-3 Enable Chapter 2 – Hardware Information...
List of Connectors Please refer to the table below for all of the system’s connectors that you can configure for your application. Label Function CON2 +12V AUX Power Connector CHA_FAN System FAN Connector COM2 COM 2 Connector COM3 COM 3 Connector COM4 COM 4 Connector COM5...
2.4.1 COM2 RS-232/422/485 Connector Signal Signal DCD (422TXD-/485DATA-) RXD (422RXD+) TXD(422TXD+/485DATA+) DTR (422RXD-) RI/+12V/+5V N.C. 2.4.2 COM3/COM4/COM5 RS-232 Serial Port PIN HEADER (COM3/COM4/COM5) Signal Signal 2.4.3 Serial ATA Power Connector (SATA_PWR1) Signal Signal +12V Chapter 2 – Hardware Information...
Hard Disk Drive Installation Step 1: Unfasten the four screws of the AEC-6643. Step 2: Get the HDD and HDD Bracket ready. Fasten four shock washers to the HDD Bracket. Step 3: Fasten the four screws to fix the HDD and HDD bracket.
Step 4: Fasten the four screws to install the HDD and HDD Bracket to the chasis, then connect the SATA cable to the HDD. Step 5: Close the cover of the AEC-6643 and fasten the screws and copper cylinders. 2.6 Memory Installation Step 1: Unfasten the four screws of the AEC-6643.
Page 26
Step 3: Line up the pins and firmly (but not roughly) press on the outside of Memory Card to install. Step 4: Snap the DIMM slot tabs shut, locking the Memory Card in place. Chapter 2 – Hardware Information...
Wallmount Kit Installation Get the brackets ready and fasten appropriate four screws on each bracket. After fastening the two brackets on the bottom lid of AEC-6643, the wallmount kit installation has been finished. Chapter 2 – Hardware Information...
System Test and Initialization The system uses certain routines to perform testing and initialization. If an error, fatal or non-fatal, is encountered, a few short beeps or an error message will be outputted. The board can usually continue the boot up sequence with non-fatal errors. The system configuration verification routines check the current system configuration against the values stored in the CMOS memory.
AMI BIOS Setup The AMI BIOS ROM has a pre-installed Setup program that allows users to modify basic system configurations, which is stored in the battery-backed CMOS RAM and BIOS NVRAM so that the information is retained when the power is turned off. To enter BIOS Setup, press <Del>...
3.3.1 Main: Security Change User/Administrator Password You can set a User Password once an Administrator Password is set. The password will be required during boot up, or when the user enters the Setup utility. Please Note that a User Password does not provide access to many of the features in the Setup utility. Select the password you wish to set, press Enter to open a dialog box to enter your password (you can enter no more than six letters or numbers).
3.4.1 Advanced: ACPI Setting Options summary: Show Turn Off String Disabled Default Enabled Enable or disable ‘It is now safe to turn off your computer. ” String Chapter 3 – AMI BIOS Setup...
3.4.2 Advanced: CPU Configuration Options summary: Hyper-Threading Disabled Enabled Optimal Default, Failsafe Default En/Disable CPU Hyper-Threading function Execute Disable Bit Disabled Enabled Optimal Default, Failsafe Default XD can prevent certain classes of malicious buffer overflow attacks when combined with a supporting OS (Windows Server 2003 SP1, Windows XP SP2, SuSE Linux 9.2, RedHat Enterprise 3 Update 3.) Limit CPUID Disabled...
3.4.4 Advanced: Intel IGD Configuration Options summary: IGFX – Boot Type VBIOS Default Optimal Default, Failsafe Default Select the video Device which will be activated during POST. This has no effect if external graphics present. Chapter 3 – AMI BIOS Setup...
3.4.6 Advanced: SATA Configuration Options summary: SATA Controllers Disabled Enabled Default SATA Ports (0-1) Device Names if Present and Enabled. SATA Mode Default AHCI (1) IDE Mode. (2) AHCI Mode. Chapter 3 – AMI BIOS Setup...
3.4.7 Advanced: USB Configuration Options summary: Legacy USB Support Enabled Optimal Default, Failsafe Default Auto Enables Legacy USB support. AUTO option disables legacy support if no USB device are connected. DISABLE option will keep USB devices available only for EFI applications. EHCI Hand-off Disabled Optimal Default, Failsafe Default...
3.4.8 Advanced: Onboard Devices Configuration Options summary: HD Audio Controller Enabled Optimal Default, Failsafe Default Disabled Enabled/Disabled Azalia HD Audio. Serial Port 1 Enabled Optimal Default, Failsafe Default Disabled Enable or Disable Serial Port Serial Port 2 Enabled Optimal Default, Failsafe Default Disabled Enable or Disable Serial Port Serial Port 2 Mode...
Serial Port 4 Enabled Optimal Default, Failsafe Default Disabled Enable or Disable Serial Port 3.4.9 Advanced: APM Options summary: Restore AC Power Loss Power Off Optimal Default, Failsafe Default Power On Last State Specify what state to go when power is re-applied after a power failure (G3 state). Power On By PCIE Disabled Optimal Default, Failsafe Default...
Setup submenu: Boot Options summary: Bootup NumLock State Optimal Default, Failsafe Default Select the key board NumLock state Full Screen Logo Disabled Optimal Default, Failsafe Default Enabled Enables/Disables Full Screen Logo Option ROM Messages Force BIOS Set display mode for Option ROM Keep Current Set display mode for option ROM Chapter 3 –...
Product CD/DVD The AEC-6643 comes with a product DVD that contains all the drivers and utilities you need to setup your product. Insert the DVD and follow the steps in the autorun program to install the drivers. In case the program does not start, follow the sequence below to install the drivers.
Page 49
Drivers will be installed automatically Step 4 – Install Audio Driver Open the STEP4 - Audio folder and select your OS Open the Setup.exe file in the folder Follow the instructions Drivers will be installed automatically Step 5 – Install AHCI Driver Please refer to Appendix C AHCI Settings Chapter 4 –...
Setting AHCI OS installation to setup AHCI mode Step 1: Copy below files from “Driver CD -> Step7-RAID&AHCI\ WinXP_32” to Disk. Step 2: Connect the USB Floppy drive to the board and insert the diskette from previous step. Step 3: Configure SATA Controller to AHCI mode in BIOS SETUP Menu: Advanced -> SATA Configuration ->...
Page 67
Step 4: Configure DVD/CD-ROM drive as the first boot device. Step 5: Save changes and exit BIOS SETUP Appendix C – AHCI Settings...
Page 68
Step 6 – Boot to DVD/CD-ROM device to install OS Step 7 – Press “F6” to install AHCI driver Step 8 – Press “S” to install AHCI driver Appendix C – AHCI Settings...
Page 69
Step 9 – Choose “Intel(R) NM10 Express Chipset”. Step 10 – The following messages will appear on the screen. Press “S” to specify additional SCSI adapters. Press “ENTER” and Windows Setup will continue to install OS. Appendix C – AHCI Settings...