Page 1
052-1196-4 Alabaster 42" (106.7 cm) Ceiling Fan Instruction Manual READ AND SAVE THESE INSTRUCTIONS...
Page 2
Safety Rules–Read and Save These Instructions 1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before installing. 2. All wiring must be in accordance with the national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
Unpacking Your Fan Unpack and inspect fan carefully to be certain all contents are included. 1. Blades (5) 2. Mounting bracket 3. Fan motor assembly 4. Motor housing 5. Blade arms (5) 6. Glass shade 7. Light kit Hardware bag 8.
Hanging the Fan Warning: Turn off the power. Follow the steps below to hang your fan properly. Outlet box 1. Unscrew three mounting bracket screws from the mounting bracket and plate. Safety cable Slot 2. Carefully lift the fan motor assembly (without the blades) and Plate insert the plate of the fan motor assembly into the slot in Motor...
Finishing the Fan Installation 1. Tilt the motor assembly up into position under the mounting plate. Secure the plate to the mounting bracket with the 3 mounting bracket screws provided (see Fig. 7). 2. Unscrew the 4 motor housing screws from the side of the mounting bracket.
Attaching the Fan Blades 1. Attach the blade to the blade arm using the blade screws as shown in Fig. 9. 2. Tighten each screw. Make sure the blade is straight. 3. Fasten one blade assembly to the motor using the two blade arm screws and spring washers supplied (see Fig.
Page 8
Fan Without Light Kit (Optional) 1. Disassemble the switch housing cover from the light kit by removing the nut and washer on the centre of the switch housing cover. Keep the light kit for future use (see Fig. 11). 2. Attach the plastic plug to the switch housing cover. 3.
Operating Your Fan Turn on the power and check the operation of your fan. There are two pull chains available in your fan: 1. 3-speed pull chain. Controls the fan speed as follows: 1 pull: high; 2 pulls: medium; 3 pulls: low; and 4 pulls: off. Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, and so on.
"making the electrical connections." Warranty This Noma® product carries a limited ten (10) year warranty against defects in the motor, and a one (1) year warranty against defects in workmanship and materials. Trileaf Distribution agrees to replace the defective product free of charge within the stated warranty period, when returned by the original purchaser with proof of purchase.
Page 11
052-1196-4 Ventilateur de plafond de 42 po (106,7 cm) Alabaster Guide d’utilisation LISEZ ET CONSERVEZ CES CONSIGNES...
Page 12
Règles de sécurité : lisez et conservez ces consignes. 1. Pour réduire le risque de choc électrique, assurez-vous que le courant est coupé au niveau du disjoncteur ou du coffret à fusibles avant l’installation. 2. Tout câblage doit être installé conformément aux codes électriques nationaux et locaux. L’installation électrique devrait être effectuée par un électricien qualifié...
Unpacking Your Fan Déballez et inspectez soigneusement le ventilateur pour vous assurer qu’il ne manque aucune pièce. 1. Pales (5) 2. Support de montage 3. Bloc moteur 4. Boîtier du moteur 5. Bras de pale (5) 6. Abat-jour en verre 7.
Suspension du ventilateur Avertissement : coupez le courant. Suivez les étapes ci-dessous pour suspendre correctement votre ventilateur. Boîte à prises 1. Dévissez trois vis du support de montage y plaque. Câble de sécurité 2. Soulevez délicatement le bloc moteur (sans les pales) et insérez Fente la plaque du bloc moteur dans la fente située sur la plaque de Plaque...
Page 16
Finir l’installation du ventilateur 1. Inclinez le bloc moteur vers le haut pour le positionner sous la plaque de montage. Fixez la plaque au support de montage en utilisant les 3 vis fournies (voir Fig. 7). 2. Dévissez les 4 vis du boîtier du moteur situées sur le côté du support de montage.
Fixation des pales du ventilateur 1. Fixez la pale au bras de pale en utilisant les vis de pales tel qu’illustré dans la Fig. 9. 2. Serrez chaque vis. Assurez-vous que la pale est droite. 3. Fixez un bloc de pale au moteur à l’aide des deux vis de bras de pale et des rondelles à...
Page 18
Ventilateur sans luminaire (optionnel) 1. Séparez le couvercle du boîtier de l’interrupteur et le luminaire en ôtant l’écrou et la rondelle situés au centre du couvercle du boîtier de l’interrupteur. Conservez le luminaire pour toute utilisation ultérieure (voir Fig. 11). 2.
Page 19
Fonctionnement de votre ventilateur Établissez le courant et vérifiez l’état de marche de votre ventilateur. l y a deux chaînettes sur votre ventilateur : 1. Une chaînette à 3 vitesses. Elle contrôle la vitesse du ventilateur comme suit : tirer 1 fois pour la grande vitesse, tirer 2 fois pour la vitesse moyenne, tirer 3 fois pour la faible vitesse, tirer 4 fois pour arrêter le ventilateur.
Exclusion : usure ou bris causés par un usage abusif ou inapproprié. Noma est une marque déposée de la compagnie Noma et est utilisée sous licence. Fabriqué en Chine Importé par...