Adjusting Airflow Direction - Carrier 40TSV0131UP Owner's Manual

5

Adjusting airflow direction

For best cooling, adjust the louvers (adjustment plates
of up/down wind direction) appropriately. Cold air
descends, so to, and to cool a room tilt them
horizontally.
For cooling (COOL)
Direct the louvers horizontally.
• When the air conditioner is not working, the louvers
are directed horizontally automatically.
Wireless remote controller
To set the airflow direction
1
1
FIX button
• The louver angle does not change immediately
after the FIX button is pushed. Check the louver
status, and push FIX button after a while.
• In subsequent operations, the vertical airflow is
automatically set in the direction to which you
adjusted the louver using the FIX button.
27-EN
1115350208_EN-TH.indb 14 1115350208_EN-TH.indb 14
To automatically swing the airflow
direction
Perform this function when the air conditioner is in
operation.
1
1
SWING button
Press the SWING button on the remote controller.
• To stop the function, press the SWING button.
CAUTION
• The FIX and SWING buttons will be disabled when the
air conditioner is not in operation (including when the
ON timer is set).
• The louver angle does not change if the FIX button is
pushed during SWING operation. Stop the SWING
operation before changing the louver angle.
• Do not operate the air conditioner for long hours with
the airflow direction set downward during the cooling
or dry operation.
Otherwise, condensation may occur on the surface of
the vertical airflow louver and cause dew dripping.
• Do not move the vertical airflow louver manually.
Always use the FIX button.
If you move the louver manually, it may malfunction
during operation.
If the louver malfunctions, stop the air conditioner
once, and restart.
• When the air conditioner is started immediately after it
was stopped, the vertical airflow louver might not
move for 10 seconds or so.
• Louver operation is limited when performing group
control.
Wired remote controller
How to set up the louver direction
1
Push during operation.
The louver direction changes for every push of the
button.
In COOL / DRY operation
Direct the louver (adjustment plate of up / down wind
direction) horizontally. If directing it downward, the dew
may form on the surface of the air discharge port and
may drop down.
Initial setup
In FAN operation
Select a desired louver direction.
Initial setup
How to start swinging
1
Push , set the louver (adjustment plate
of up / down wind direction) direction to the
lowest position, and then push
SWING is displayed and the up / down louver
direction is automatically selected.
Display during swinging
Repeat
How to stop swinging
1
Push at a desired position while the
louver is swinging.
• When is pushed after that, wind
direction can be set again from the highest
position.
– 14 –
1 Unit select button
* However, even if is pushed while the
louver is swinging, the louver position is
displayed as follows and highest position of the
louver may not be selected.
Display when swinging is stopped
Fan operation
Cool / Dry
operation
In this case, push again two seconds later.
• In Cool / Dry operation, the louver does not stop
as it directs downward. If stopping the louver as
it directs downward during swing operation, it
stops after moving to the third position from the
highest position.
Display when stopping the swing
Cool / Dry
Fan operation
operation
Unit select button
• When multiple indoor units are controlled with one
again.
remote controller, louver direction can be set for
each indoor unit by selecting individually.
• To set louver direction individually, push
button to display an indoor unit number in the control
group. Then set the wind direction of the displayed
indoor unit.
• When no indoor unit number is displayed, all indoor
units in the control group can be controlled
simultaneously.
• Each time button is pushed, the display
changes as follows:
UNIT No. UNIT No. UNIT No.
1-1 1-2 1-3
Not UNIT No.
display 1-4
EN
TH
28-EN
3/29/2559 BE 6:54 PM 3/29/2559 BE 6:54 PM