Precautions For Safety; Indoor Unit Display; Remote Control; Preparation Before Use - Carrier 42TSR010 series Owner's Manual

PRECAUTIONS FOR SAFETY

• Do not install, repair, open or remove the cover. It may expose you to dangerous voltages. Ask the dealer or the specialist to do this.
• Turning off the power supply will not prevent potential electric shock.
DANGER • The appliance shall be installed in accordance with national wiring regulation.
• Means for disconnection from the supply having a contact separation of at least 3 mm in all poles must be incorporated in the fi xed
wiring.
• Do not expose your body directly to cool air for a long time.
• Do not insert your fi nger or any article into the air inlet/outlet.
• When an abnormality (burning smell, etc.) occurs, stop the air conditioner and disconnect the power supply or turn off the breaker.
WARNING • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not wash the unit with water. It may cause an electric shock.
• Do not use this air conditioner for other purposes such as preserving food, breeding animal, etc.
• Do not step or put anything on the indoor/outdoor unit. It may cause an injury or damage the unit.
• Do not touch aluminium fi n because it may cause an injury.
CAUTION
• Before cleaning the unit, turn off the main switch or the circuit breaker.
• When the unit won't be used for a long time, turn off the main switch or the circuit breaker.
• It is recommended that maintenance be performed by a specialist when the unit has been operated for a long time.
1

INDOOR UNIT DISPLAY

2

PREPARATION BEFORE USE

Preparing Filters
1. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1. Push by tip of the pencil.
ON OFF
2. Press or
3. Press : Set the time.
Remote Control Reset
1. Remove the battery.
2. Press .
3. Insert the battery.
3

AIRFLOW DIRECTION

1 Press : Move the louver in
the desired vertical direction.
Press : Swing the air
2
automatically and press again to
stop.
For horizontal direction, adjust
3
manually.
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by come operation mode.
1110250174.indd 2 1110250174.indd 2
1 Hi POWER (Green)
2 FILTER (Orange)
3 FAN-ONLY (Orange)
4 TIMER (Yellow)
5 OPERATION (Green)
6 RESET button
: adjust the time.
4

REMOTE CONTROL

1 Infrared signal emitter
2 Start/Stop button (
)
3 Mode select button (
)
4 Temperature button (
)
5 Fan speed button (
)
6 Swing louver button (
)
7 Set louver button (
)
8 On timer button ( ON
)
9 Off timer button (
)
OFF
! Sleep timer button (
)
" Setup button (
)
# Clear button (
)
$ Memory and Preset button (
)
% High power button (
)
& Economy button (
)
( Filter reset button (
)
) Clock Reset button (
)
~ Check button (
)
Note: Some models, remote will have text above the buttons.
5

AUTOMATIC OPERATION

To automatically select cooling, or fan only operation
1. Press : Select A.
2. Press : Set the desired temperature.
6 COOLING / FAN ONLY OPERATION
1. Press : Select Cool , or Fan only
2. Press : Set the desired temperature.
Cooling: Min. 17°C, Fan Only: No temperature indication
3. Press : Select AUTO, LOW , LOW+
MED+ , or HIGH .
7

DRY OPERATION

For dehumidifi cation, a moderate cooling performance is controlled
automatically.
1. Press : Select Dry .
2. Press : Set the desired temperature.
ON OFF
.
, MED ,
1/28/10 3:46:23 PM 1/28/10 3:46:23 PM