fadini junior 633 Instruction Manual
230 v
Hide thumbs
Also See for junior 633:
- Instruction manual (21 pages) ,
- Instruction manual (17 pages) ,
- Instruction manual (56 pages)
Related Manuals for fadini junior 633
Summary of Contents for fadini junior 633
- Page 1 GB - Instructions Manual pag. 17-32 Junior 633 - Junior 650 230 V EN 13241 EN 12453 EN 12445 the gate opener...
-
Page 2: Before Installation
□ Meccanica Fadini is technician (on -call). □ Any maintenance operation must be done by not liable for damages caused by the incorrect use of the equipment, or qualified technicians. -
Page 3: Declaration Of Conformity
IS IN COMPLIANCE WITH THE NORMS..2006/42/CE Junior 633 is to be sold and installed as a comprehensive “Automatic System”, including the accessories and components as recommended by the Manufacturing Company. In observance of the current directives, any automation is to be regarded as a “machine”. Therefore it is required that all the applicable safety norms are strictly complied with by installation agents, who are also required to issue a Declaration of Conformity. - Page 4 N - Encoder S - Programmer cover O - Electrical Motor 230V - 0.33 HP T - 230V - 24V - 20VA Transformer for Junior 633 and Junior 650 Pic. 2 U - Electrical motor 230V - 0.5 HP P - Electrical power disconnection microswitch for the unlocking handle...
-
Page 5: Anchor Plate
CASING OPENING ANCHOR PLATE ATTENTION: once the two side screws have ATTENTION: the nut under the plate must be been removed, lift the casing and vertically pull it out, without tearing off the “led” card 47 mm from the end of the bolt cable connector. - Page 6 The first operation to be performed is to identify the Junior installation with respect to the opening of the gate, moving Dip-Switch n°11 on the Elpro 63 programmer (already installed on the Junior 633/Junior 650), depending on the position of Junior as seen inside the gate to be opened.
- Page 7 FASTENING THE LIMIT SWITCH BRACKETS TO THE GEAR RACK ATTENTION: do not open and invert the single magnets inside the limit switch plastic brackets. These have already been properly installed to be identified by programmer logic Right bracket Dx of the magnetic limit switch Sx Left bracket of the magnetic limit switch NOTE WELL: IT IS MOST IMPORTANT THAT THE GATE DOES NOT RUN INTO THE GATE STOPS IN OPENING AND CLOSING CYCLES.
- Page 8 3. jumper inserted and safety edges activated, reversing in opening and closing for twice as much the travel bit 2. jumper inserted and safety edges activated, ATTENTION: USING ACCESSORIES THAT ARE NOT FADINI automatic re-closing after dwell time MAY RESULT INTO DAMAGES TO THE BOARD.
- Page 9 It is furthermore recommended that the “Safety Regulations” made available by Meccanica Fadini be examined throughly. General description: The Elpro 63 is a PCB card with microprocessor for the command and management of the Junior 633 and Junior 650 sliding gate opener with programming for self-learning of the different movement phases of the gate.
- Page 10 Elpro 63 ELECTRICAL CONNECTIONS TO THE TERMINALS AND THEIR FUNCTIONS Accessory Electrical connections Dip-switches and LED indication of their functions Photocells in closing: DIP-SWITCH 1 ON: stops gate on opening and reverses it on All of the NC contacts on the Photocells closing once obstacle is removed in closing phase must be connected in OFF: no stop on opening, gate is reversed on...
- Page 11 Dip-switches and LED indication of their functions DIP-SWITCH 12 Connections for n°2 It is important to determine which Elpro 63 MASTER will Junior 633 or Junior 650 command and control the Elpro 63 SLAVE. ON: Elpro 63 SLAVE (2 Junior 633/Junior 650)
- Page 12 Elpro 63 ELECTRICAL CONNECTIONS TO THE TERMINALS AND THEIR FUNCTIONS SAFETY EDGES The two inputs, that are tted to control the safety edges, are separated for the opening and closing phases and are recognized by the Elpro 63 board during the programming phase.
- Page 13 Elpro 63 FUNCTIONS: DESCRIPTION OF THE FUNCTIONS OF THE JUNIOR 633 AND JUNIOR 650 SLIDING GATE OPERATORS NOTE WELL: any variation on the DIP-SWITCH setting, to achieve the required functions, will be performed on the subsequent command to open or close, with the exception of DIP-SWITCH No.11 that is learnt and memorized only in the programming phase.
- Page 14 Elpro 63 PROGRAMMING AND SELF-LEARNING OF THE GATE RUN IMPORTANT: programming Junior is performed at first installation. Even in absence of mains power, programming is retained in the memory. In case any time position of the limit switch brackets is changed, functions setting by mean of dip-switches or accessories connections are modified, the gate run setting is to be re-programmed accordingly, following the same procedure.
- Page 15 OPENING OF THE UNLOCKING HANDLE FOR THE MANUAL OPERATION OF THE GATE By opening the unlocking handle with the coded key, the electrical power supply is always disconnected from the system. For unlocking action and subsequent manual movement of the gate, it is necessary that the handle be opened until it stops beyond 90°.
-
Page 16: Maintenance Record
NOTE WELL: this document must record any ordinary and extraordinary services including installation, maintenance, repairs and replacements to be made only by using Fadini original spare parts. This document, for the data included in it, must be made available to authorized inspectors/o cers, and a copy of it must be handed over the end user/s. -
Page 17: Dati Tecnici
DATI TECNICI TECHNICAL SPECIFICATIONS Dati tecnici JUNIOR 633 JUNIOR 650 Technical specifications JUNIOR 633 JUNIOR 650 Tensione di alimentazione 230 V - 50 Hz 230 V - 50 Hz Electrical power supply voltage 230 V - 50 Hz 230 V - 50 Hz... - Page 18 296 mm Ø10,2 Piastra di fondazione Base plate Plaque de fondation Timbro dell’Installatore Installer’s Stamp Cachet de l’installateur Via Mantova, 177/A - 37053 Cerea (VR) Italy - Ph. +39 0442 330422 - Fax +39 0442 331054 info@fadini.net - www.fadini.net...
Need help?
Do you have a question about the junior 633 and is the answer not in the manual?
Questions and answers