All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without the prior permission of Philips. Published by EL 0666 BG CD Customer Service...
EN 2 BJ2.4U/BJ2.5U PA Technical Specifications, Connections, and Chassis Overview 1. Technical Specifications, Connections, and Chassis Overview Index of this chapter: 1.1.2 Sound 1.1 Technical Specifications 1.2 Connection Overview Sound systems : AV Stereo 1.3 Chassis Overview : BTSC Maximum power (W...
Page 3
1.2.2 Digital Media Reader with USB2.0 (for BJ2.4 U PA chassis) AV1 Cinch: Video YPbPrHV- In In sets with the BJ2.4U PA chassis, a 6-in-1 card reader unit is Gn - Video Y / 75 ohm available, which is connected via USB to the Small Signal Bu - Video Pb 0.7 V...
Page 4
EN 4 BJ2.4U/BJ2.5U PA Technical Specifications, Connections, and Chassis Overview DIGITAL AUDIO Cinch: S/PDIF - In AV3 Cinch: Video YPbPr - In Bk - Coaxial 0.2 - 0.6V / 75 ohm Rd - Video Pr 0.7 V / 75 ohm Bu - Video Pb 0.7 V...
Safety Instructions, Warnings, and Notes BJ2.4U/BJ2.5U PA EN 5 2. Safety Instructions, Warnings, and Notes Index of this chapter: Service Default Mode (see chapter 5) with a colour bar 2.1 Safety Instructions signal and stereo sound (L: 3 kHz, R: 1 kHz unless stated 2.2 Warnings...
Page 6
2.3.5 Alternative BOM identification Figure 2-1 Serial number example In September 2003, Philips CE introduced a change in the way Regardless of the special lead-free logo (which is not always the serial number (or production number, see Figure 2-1) is indicated), one must treat all sets from this date onwards composed.
Directions for Use BJ2.4U/BJ2.5U PA EN 7 3. Directions for Use You can download this information from the following websites: http://www.philips.com/support http://www.p4c.philips.com...
EN 8 BJ2.4U/BJ2.5U PA Mechanical Instructions 4. Mechanical Instructions Index of this chapter: Notes: 4.1 Cable Dressing • Figures below can deviate slightly from the actual situation, 4.2 Service Positions due to the different set executions. 4.3 Assy/Panel Removal •...
Page 9
Mechanical Instructions BJ2.4U/BJ2.5U PA EN 9 Assy/Panel Removal 1. Remove the cables that are guided by the speaker frame from its clamps [1]. 2. Remove parker T10 screws [2] that hold the frame and pull 4.3.1 Metal Back Plate the frame downwards.
Page 10
EN 10 BJ2.4U/BJ2.5U PA Mechanical Instructions panel removal”. The cable can not be disconnected from the assy at this moment. G_15960_099.eps 070306 Figure 4-8 Control panel removal The assy is packed into two plastic frames. To unpack the G_15960_098.eps 100306 inner frame, lift the two clamps [1] of the outer frame and take the inner frame out.
Page 11
Mechanical Instructions BJ2.4U/BJ2.5U PA EN 11 9. Remove screws [8]. 10. Remove SSB from the set. G_15930_081.eps G_15930_078.eps 190606 190606 Figure 4-12 Rear SSB shield Figure 4-15 SDI PDP Power supply panel 1. Unplug connectors [1]. 2. Remove screws [2].
Page 12
EN 12 BJ2.4U/BJ2.5U PA Mechanical Instructions G_15960_104.eps 070306 Figure 4-17 AmbiLight diffusor frame lift 4.3.12 Now the AmbiLight lamp units can be removed from the frame. Each of them is fixed with four T10 parker screws: two on the inside and two on the outside of the frame.
Page 13
Mechanical Instructions BJ2.4U/BJ2.5U PA EN 13 12. Remove screws [10]. 13. Use brackets [11] to lift the panel from the set and put it at a safe place. 14. Remove screws [12] and the brackets from the panel, and install the brackets on the new panel.
EN 14 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding 5. Service Modes, Error Codes, and Fault Finding Index of this chapter: in the channel map and could be different from the one 5.1 Test Points corresponding to the physical channel 3.
Page 15
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 15 5.2.2 Service Alignment Mode (SAM) Note: When you have a corrupted NVM, or you have replaced the NVM, there is a high possibility that you will not have picture any more because your display option is not correct.
Page 16
EN 16 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding Clarification Resolution Nr of bits Year Code nr Dimming Displays Size Clear Ver Output Hor Output Div.Displays Display Type Brand Full HD (Inch) analog Full Baby 768p 1024 V3_SA42AX-****-Rev,2...
Page 17
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 17 5.2.3 Customer Service Mode (CSM) • Digital Processing. Indicates the selected digital mode. Possible values are “STANDARD” and “PIXEL PLUS”. Change via “MENU”, “TV”, “PICTURE”, “DIGITAL Purpose PROCESSING”. When a customer is having problems with his TV-set, he can •...
Page 18
EN 18 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding • POD key validity. Indicates the key’s validity, this will only • Switches the Ambi Light board to protection if needed (in work with an authentic POD card. case of protection only the lamps switch off, no set •...
Page 19
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 19 Repair Tips when the TV is in a protection state detected via the Stand-by In case only one or no lamp unit at all works, probably the Processor (and thus blinking an error) and SDM is activated via +12Vb (12 - 13 V) is not available or the fuse is broken.
Page 20
EN 20 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding Stand-by or action holder: MIPS Protection action holder: St-by Mains is applied autonomous action Standby Supply starts running. +5V2, 1V2Stb, 3V3Stb and +2V5D become present. In case of PDP 3V3 Vpr to CPU PDP becomes present.
Page 21
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 21 From part A From part B action holder: MIPS action holder: St-by autonomous action detect-1V2 received within +1.2V error 250ms? Enable the supply for +2.5V and +3.3V (ENABLE-3V3) No separate enable and detect is present for the +2V5 supply in the Baby Jaguar.
Page 22
EN 22 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding From part B From part B From part B action holder: MIPS Wait 10ms action holder: St-by Enable Alive check mechanism autonomous action Switch the NVM reset line HIGH.
Page 23
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 23 42" FHP A1 Semi Standby action holder: MIPS action holder: St-by Assert RGB video blanking and audio mute autonomous action Initialize audio and video processing IC's and functions according needed use case.
Page 24
EN 24 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding 42" / 50" SDI V4 action holder: MIPS action holder: St-by autonomous action Semi Standby Assert RGB video blanking and audio mute Initialize audio and video processing IC's and functions according needed use case.
Page 25
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 25 42" FHP A1 action holder: MIPS Active action holder: St-by autonomous action Mute all sound outputs. Switch reset-audio and sound-enable lines high Blank by sending ADEN = 0 to PDP display...
Page 26
EN 26 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding 42" / 50" SDI V4 action holder: MIPS Active action holder: St-by autonomous action Mute all sound outputs. Switch RESET_AUDIO and SOUND_ENABLE lines “high” Blank PDP display. Mute all video outputs.
Page 27
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 27 Semi Stand by action holder: MIPS action holder: St-by Delay transition until ramping down of ambient light is finished. *) autonomous action *) If this is not performed and the set is...
Page 28
EN 28 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding Semi Stand by This state transition is entered when standby is requested action holder: MIPS and an authenticated POD is present. When in semi- action holder: St-by standby, the CEservices will set the POD standby NVM bit and ask infra to reboot.
Page 29
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 29 POD stand by action holder: MIPS action holder: St-by Switch “on” all supplies by switching “low” the ON-MODE I/O line. autonomous action Full SSB power and the display related supplies...
Page 30
EN 30 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding Semi Stand by action holder: MIPS action holder: St-by Delay transition until ramping down of ambient light is finished. *) autonomous action *) If this is not performed and the set is...
Page 31
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 31 Semi Stand by This state transition is entered when standby is requested action holder: MIPS and an authenticated POD is present. When in semi- action holder: St-by standby, the CEservices will set the POD standby NVM bit and ask infra to reboot.
Page 32
EN 32 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding action holder: MIPS transfer Wake up reasons to the Stand by µP. action holder: St-by autonomous action Images are re-transferred to DDR-RAM from Flash RAM (verification through checksum) MIPS image completes the application reload, stops DDR-RAM access, puts itself in a sleepmode and signals the standby µP when the...
Page 33
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 33 Log the appropriate error and action holder: MIPS set stand-by flag in NVM action holder: St-by Redefine wake up reasons for protection autonomous action state and transfer to stand-by µP.
Page 34
CONNECTOR 5.4.1 ComPair Introduction ComPair (Computer Aided Repair) is a service tool for Philips Consumer Electronics products. ComPair is a further development on the European DST (service remote control), I 2 C which allows faster and more accurate diagnostics. ComPair...
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 35 Error Codes – 00 00 00 00 00: No errors detected – 06 00 00 00 00: Error code 6 is the last and only detected error 5.5.1 Introduction –...
Page 36
EN 36 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding Extra Info communication between channel decoder and tuner. See • Rebooting. When a TV is constantly rebooting due to schematic B2B. internal problems, most of the time no errors will be logged •...
Page 37
Service Modes, Error Codes, and Fault Finding BJ2.4U/BJ2.5U PA EN 37 5.6.2 How to Activate Fault Finding and Repair Tips Use one of the following methods: Read also paragraph "Error Codes" - "Extra Info". • Activate the SDM. The blinking front LED will show the entire contents of the error buffer (this works in “normal...
Page 38
EN 38 BJ2.4U/BJ2.5U PA Service Modes, Error Codes, and Fault Finding • Then, after this voltage becomes present and is detected Note 1: If fuse 1U01 is broken, this usually means a pair of OK (about 100 ms), the other two voltages (+2V5 and defective power MOSFETs (7U01 or 7U03).
Page 39
TV into the software upgrade application. To do so: • Disconnect the TV from the Mains/AC Power. • Press the “OK” button on a Philips DVD RC-6 remote control (it is also possible to use the TV remote in "DVD" mode). •...
Block Diagrams, Test Point Overviews, and Waveforms BJ2.4U/BJ2.5U PA Wiring Diagram 42” & 50” SDI WIRING 42” / 50” SDI TOP TOP AMBI LIGHT TOP AMBI LIGHT 8508 (OPTIONAL) (OPTIONAL) 8539 AMBI AMBI LIGHT LIGHT SDI PDP POWER SUPPLY 8900...
Block Diagrams, Test Point Overviews, and Waveforms BJ2.4U/BJ2.5U PA Block Diagram Video VIDEO MAIN TUNER + OOB TUNER MPIF MAIN: PNX2015: VIPER: VIPER: MAIN MEMORY 7C00 7J00 7V00 PNX3000HL 7V01 PNX2015E PNX8550 K4D551638F 1T04 1C52 TUNNELBUS VIFINP TD1336O SOUND GROUP...
Block Diagrams, Test Point Overviews, and Waveforms BJ2.4U/BJ2.5U PA Block Diagram Audio AUDIO PDP MAIN TUNER + OOB TUNER MPIF MAIN: AUDIO SOURCE SELECTION PNX2015 MPIF MAIN: MPIF MAIN: AUDIO LEFT RIGHT PROTECTION / AUDIO AMPLIFIER CONNECTIONS B MUTE CONTROL...
Block Diagrams, Test Point Overviews, and Waveforms BJ2.4U/BJ2.5U PA Block Diagram Control CONTROL VIPER: CONTROL USB 2.0: HOST VIPER: A/V + TUNNELBUS AMBI LIGHT 1M11 7001 7018 P87LPC760 7015 5014 7009 1M59 7V00 7N00 ISP1561BM PNX8550EH TO 1M59 MICRO 3H14...
Block Diagrams, Test Point Overviews, and Waveforms BJ2.4U/BJ2.5U PA Supply Lines Overview SUPPLY LINES OVERVIEW PDP B10B POD: OUT OF BAND MAIN TUNET + OOB TUNER PNX 2015: TUNNELBUS VIPER: DISPLAY DIVERSITY + AMBILIGHT SUPPLY DC/DC CONNECTIONS +3V3 +3V3 +8V6-SW...
Alignments BJ2.4U/BJ2.5U PA EN 115 8. Alignments Index of this chapter: With the software alignments of the Service Alignment Mode 8.1 General Alignment Conditions (SAM), “Tuner AGC” and the “Whitepoint” settings can be 8.2 Hardware Alignments aligned. 8.3 Software Alignments To store the data: 8.4 Option Settings...
Page 116
EN 116 BJ2.4U/BJ2.5U PA Alignments 1. Select a COLOUR TEMPERATURE (e.g. COOL, NORMAL, or WARM). 2. Set the RED, GREEN and BLUE default values according to the values in the "Tint settings" table. 3. When finished press STORE (in the SAM root menu) to store the aligned values to the NVM.
Page 117
Alignments BJ2.4U/BJ2.5U PA EN 117 8.4.2 Dealer Options Table 8-3 Dealer options Menu item Subjects Options Description Personal Options Picture Mute Picture mute active in case no picture detected Noise in case of no picture detected Virgin Mode TV starts up (once) with a language selection menu after the Mains switch is turned "on" for...
Page 118
3 (8) Interconnect China IF 0= Off, 8= On 4 (16) Alternative Tuner 0= Philips, 16= Alps Tuner make. 5 (32) Tuner Type 0= TD1336s (B-Chassis US), 32= TD1331(J-Chassis US), Tuner type 64= UV1318 (Analogue EU), 96= TD1316 (Hybrid EU) (B-chassis US is e.g "BP2.3U").
Page 119
Alignments BJ2.4U/BJ2.5U PA EN 119 Byte Bit (dec. value) Subject Options Settings (in decimal values) Remarks 0 (1) Display Screen 000 (0000)= 42-inch PDP (SDI) HD V3, 001 (0256)= 50-inch PDP (SDI) HD V3, Screen size, type, and resolution. 002 (0512)= 42-inch PDP (FHP) ALiS, 003 (0768)= 30-inch LCD (LPL),...
EN 120 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: Local Area Network support (future) and all kinds of 9.1 Introduction streaming applications (future). 9.2 Power Supply •...
Page 121
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 121 SSB Cell Layout LVDS DISPLAY INTERFACE DC / DC & CONV SOURCE SELECTION SIGNAL PROCESSING MPIF RS232 TUNER UART HDMI 1 HDMI 2 G_15930_085.eps 200606 Figure 9-1 SSB top view...
Page 122
EN 122 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Power Supply 9.2.5 +12V Switch • The +12V switch is activated when the POD-MODE signal 9.2.1 Introduction is "low". • The rise time of the output voltage is set by components The Main Power Supply is a buy-in module (it belongs to the 2U42, 3U43, and 3U95 at about 30 ms.
Page 123
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 123 PWM Generator and MOSFET Drivers 9.2.10 Useful Data This circuit is a one-chip solution (item 7U00). It contains all the circuitry for two independent buck regulators (3V3 and 1V2).
Page 124
EN 124 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Main Supply SUPPLY DISTRIBUTION IN STANDBY MODE d.c. power: 0.24 a.c. power: 0.94 STDBY POD STDBY +12VS +8V6 +5V2 power 0.00 0.00 0.24 0.00 DC-DC DC-DC 12V/3.3V 12V/1.2V (mA) 1.2V...
Page 125
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 125 Main Supply SUPPLY DISTRIBUTION IN POD MODE d.c. power: 10.78 a.c. power: 15.40 STDBY POD STDBY +12VS +8V6 +5V2 power 8.48 0.00 0.35 1.91 DC-DC DC-DC 12V/3.3V 12V/1.2V (mA) 1.2V...
Page 126
EN 126 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Main Supply SUPPLY DISTRIBUTION IN ON MODE d.c. power: 23.66 a.c. power: 47.38 STDBY POD STDBY +12VS +8V6 +5V2 power 20.62 2.18 0.35 12.11 DC-DC DC-DC 12V/3.3V 12V/1.2V (mA) 1.2V...
Page 127
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 127 Inputs drawn from the USB ports, the protection becomes active (= "high"). During stand-by, when there is no +5V available (and VIPER is 9.3.1 not active), the USB port does not work. This is controlled by...
Page 128
EN 128 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets – HDMI connectors (Video, Audio, HDCP, Control). HDMI Source HDMI Sink – Analogue (YPbPr, RGB, and H/V). • Control signals: – C coming from TDA9975 (MM-BUS1). Video Video –...
Page 129
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 129 – Contains manufacturer name, product name, type, etc. FRONT-END VIPER (replaced by CEC). • MPEG Source: TUNER DEMOD DEMUX – Contains flags that permit optimized display of de-...
Page 130
EN 130 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets POD Stand-by Mode – Control and Access messages. • POD stack still alive: – Application code download. – Active Front-End. – Only from cable operator towards user. –...
Page 131
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 131 • AGC at vision IF level to give fixed CVBS output level, and cntv cnta AGC at RF level (tuner AGC) to limit output level of the SCART2 out / Ext2 out Jaguar system tuner.
Page 132
EN 132 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets allow selection of the output out of five L+R inputs, two mono In the normal mode the data links can handle up to three video signals (AM internal or AM external) and two externally signals: CVBS or YC signal from the primary video selector, connected DSND streams.
Page 133
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 133 PNX2015: AVIP The receiver block gets the serial data stream and converts it to a parallel stream. This parallel data is fed to the "de- multiplexer and formatter " block where the selected audio/ 9.8.1...
Page 134
EN 134 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets DCU (Data Capturing Unit) DEMDEC (Demodulator and Decoder) Data Capture Unit DEMDEC DSP pilot demod. I2d Data_1 (cvbs) Packet DEC L/A VBI data SAP / EIAJ Decimator Data Slicer SERPAR demod.
Page 135
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 135 PNX2015: Columbus (Comb Filter) the banks via I C, by programming bits [2:0] of the SYSTEM_SELECT register. The bits [6:4] of the SYSTEM_SELECT register select, which register bank is used 9.9.1...
Page 136
EN 136 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 5. All I/O lines will be set in default state, as “told” by the software. - Lower Voltage Swing (only 350 mV vs. 3 V) - Allows faster Clocking –...
Page 137
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 137 9.13.2 Block Diagram de-interlacing and scaling tasks. It reads images from memory, performs a transformation, and writes the result back in memory. 2x225 MHz, 32-bit wide DDR Optional external coprocessors...
Page 138
EN 138 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets The primary and secondary QVCP each contain a series of Light Sensor layers and mixers. The QVCP creates a series of display data The light sensor influences the Brightness: when the room is layers (pixel streams) and mixes them logically from back to darker, the ambient light is reduced.
Page 139
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 139 SOFTWARE Picture Profiles content SetHue (H) EPLD Inverter board CCFL Profiles SetSaturation (S) personal RED left inverter RED right SetLightState GREEN left GREEN inverter GREEN right RampUp Down...
EN 140 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.15 Abbreviation List CVBS Composite Video Blanking and Synchronization Digital to Analogue Converter 0/6/12 SCART switch control signal on A/V Dynamic Bass Enhancement: extra board. 0 = loop through (AUX to TV), 6...
Page 141
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 141 Monochrome TV system. Sound On screen display Teletext and carrier distance is 6.0 MHz Control; also called Artistic (SAA5800) Integrated IC bus Project 50: communication protocol Integrated IC Data bus...
Page 142
EN 142 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets Sync On Green SOPS Self Oscillating Power Supply S/PDIF Sony Philips Digital InterFace SRAM Static RAM Small Signal Board STBY STandBY Sync On Green SVGA 800x600 (4:3) SVHS...
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 143 9.16 IC Data Sheets electrical diagrams (with the exception of "memory" and "logic" ICs). This section shows the internal block diagrams and pin configurations of ICs that are drawn as "black boxes" in the 9.16.1 Diagram B1A, NCP5422AD (IC 7U00)
Page 144
EN 144 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.2 Diagram B2A, NXT2003 (IC 7TG0) Block Diagram FAT VSB/QAM MPEG IF In text text text Demodulator Transport Sense 32K x 8 text RF Gain SRAM BERT text...
Page 145
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 145 9.16.3 Diagram B2B, UPC3220GR (IC 7T43) Block Diagram and Pin Configuration (Top View) AGC AMP. MIXER AGC IN1 MIX OUT2 AGC IN2 MIX OUT1 OSC OUT BUFFER AMP.
Page 146
EN 146 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.4 Diagram B3x, PNX3000HL (IC 7C00) Block Diagram CVBSOUTA 1× CVBSOUTB 2NDSIFEXT (FMRAD) CVBSOUTIF SIFAGC MIXER SIFIN 2nd SIF internal & AM SND DEMOD DTV 1st IF DTVOUT...
Page 147
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 147 9.16.5 Diagram B4x, PNX2015E (IC 7J00) Block Diagram 16-BIT 225 MHz DDR PNX2015 MEMORY CONTROLLER video NORTH TUNNEL SOUTH TUNNEL PNX8550 coprocessor HD input (TDA9975) MEMORY VO-1 BASED SCALER...
Page 148
EN 148 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.6 Diagram B4A, CY2305SC-1 (IC 7J08) Block Diagram Pin Configuration CY2305SC-1 CLKOUT CLKA1 SOIC Top View CLKA2 CLKOUT CLK4 CLK2 CLKA3 CLK1 CLK3 CLKA4 CLKB1 Select Input CLKB2...
Page 149
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 149 9.16.8 Diagram B5x, PNX8550EH (IC 7V00) Block Diagram Streaming Interface Optional External 32-Bit 225 MHz DDR from Tunnel Video Improvement Processing PNX8550 Memory 30 (dig) DVD-CSS 5-Layer Controller...
Page 150
EN 150 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.9 Diagram B5A, LM3526MX (IC 7Q01) Block Diagram Pin Configu Figure 9-37 Internal block diagram and pin configuration...
Page 151
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 151 9.16.10 Diagram B7B & B7C, TDA9975EL (IC 7B11) Block Diagram τ ORR/V τ I²C ORB/U τ ORG/Y G/Pb B/Pb1 B/Pb2 B/Pb3 I²C 10/12 I²C I²C CLAMP BIAS I²C I²C...
Page 152
EN 152 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.11 Diagram B8, ISP1561BM (IC 7N00) Block Diagram SMI# SEL48M PME# ISP1561BM GLOBAL CONTROL IRQ1 IRQ12 legacy keyboard and mouse support AD[31:0] PCI CORE KBIRQ1 C/BE#[3:0] REQ# MUIRQ12...
Page 153
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 153 9.16.12 Diagram B10A, TPS2211AIDB (IC 7P00) Block Diagram TPS2211A Card B V CC1 3.3 V V CC2 3.3 V V pp1 12 V V pp2 See Note A...
Page 154
EN 154 BJ2.4U/BJ2.5U PA Circuit Descriptions, Abbreviation List, and IC Data Sheets 9.16.13 Diagram B10A, STV0701 (IC 7P03) Block Diagram Pin Configuration F_15400_138.eps 240505 Figure 9-41 Internal block diagram and pin configuration...
Page 155
Circuit Descriptions, Abbreviation List, and IC Data Sheets BJ2.4U/BJ2.5U PA EN 155 9.16.14 Diagram C, TDA8925ST (IC 7701) Block Diagram V DD2 V DD1 TDA8925ST/J TDA8926J BOOT1 DRIVER HIGH CONTROL OUT1 HANDSHAKE DRIVER REL1 STAB temp V SS1 TEMPERATURE SENSOR...
Need help?
Do you have a question about the BJ2.4U and is the answer not in the manual?
Questions and answers